Products in Oil, Gas & Mining: Good Abrasion Resistance

VESTAMID® NRG 2901 BK is a high-viscosity, heat-stabilized compound with exceptional mold release properties. It is nucleated to reduce cycle time and shrinkage of molded parts. It is commonly used for gas pipes and fittings, with a proven record of safe and reliable performance in demanding applications, including fuel lines in passenger cars, air brake tubing in trucks, and offshore applications.

Pure very high molecular weight high density polyethylene homopolymer polymer in finely sized rounded powder form. Avg. = ~75 micron. Molecular weight of approximately 500,000.

SP Series™ SHP1200-1 is a ultra high molecular weight polyethylene (UHMWPE) polymer in powder form. These unique materials exhibit very high toughness. SP Series™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. SP Series™ powders are well suited for use in water, chemical and gas filter applications. SHP1200-1 can be independently sintered into a filter or used as a binder for activated carbon filter.

HNBR has excellent resistance to sour oil and gas, steam, hot water and ozonePhysical properties such as tensile and tear strength, elongation, abrasion resistance and compression set are excellent, while compounds exhibit good dynamic behavior at elevated temperaturesHNBR has excellent resistance to sour oil and gas, steam, hot water and ozoneLike EPDM, hydrogenated nitrile rubber can either be cured with sulfur or peroxide, depending upon which properties are the most importantComponents in HNBR offer an excellent range of performance at a cost between nitrile rubber and fluoroelastomers (FKM).

Pure ULTRA high molecular weight high density polyethylene homopolymer polymer in finely sized rounded powder form. Avg. = ~70- micron. Molecular weight in excess of 2,000,000.

Pure ULTRA high molecular weight high density polyethylene homopolymer polymer in finely sized rounded powder form. Avg. = ~130- micron. Molecular weight in excess of 2,000,000.

RE-FLEX® 885AJL is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

RE-FLEX® 790A is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

Hypalon® CSM Chlorosulfunated Polyethylene Rubber is to develop rubber solutions that will optimize your components performance in your applications.

Duro-Bond ETFE is a laminated sheet lining consisting of a layer of Ethylenetetrafluoroethylene (ETFE) resin laminated to a fabric backing that is readily bonded to steel, concrete, or FRP substrates.

Petroz™ 595 durometer FFKM specifically compounded for rapid gas decompression (RGD) resistance that consistently outperforms competitors’ RGD compounds.

Duro-Bond E-CTFE is a laminated sheet lining consisting of a layer of Ethylene Chlorotetrafluoroethylene (E-CTFE) resin laminated to a fabric or vulcanized soft rubber backing that is readily bonded to steel, concrete, or FRP substrates.

RE-FLEX® 785A is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

RE-FLEX® 585A is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

GAR-DUR® UHMW-PE plastic parts are made from ultra high molecular weight (UHMW) polymer having a molecular weight of 4.2 million and greater. Garland Manufacturing Company has been processing UHMW resin for over 45 years. This true UHMW polymer is excellent for resisting abrasion and corrosion while contributing a low coefficient of friction. Fabricated Gar-Dur® parts have helped companies improve performance, reduce downtime, eliminate the need for lubrication, replace steel parts and lower their operating costs.

VITON® VI70 is a commercial grade black VITON® sheet with Excellent resistance to many concentrated acids and Excellent resistance to many concentrated acids.

HY60 is a csm rubber sheet.

Kestlub® is one of the most important developments in the Kestamid® product range. Kestlub® is a special type of cast polyamide ideal for bearings. It is produced by adding lubricants to cast polyamide through special processes. It performs extremely well in bearing applications as it is self-lubricated.

RE-FLEX® 470A is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

Nylacast Nylube was introduced into the Nylacast product rangein 1989 as a logical progression to Oilon with already outstanding performance as a bearing material. Since that time, it has proved to be Nylacast’s supreme wear resisting grade and one of the most important developments from Nylacast in new materials. Nylube contains a combined liquid/solid lubricant system which allows for a coefficient of friction as low as 0.08. This is below that of almost any other polymer available at present.

Nylacast Oilon was a break through of the first magnitude in the world of cast nylons, developed in the early 70s by Nylacast and introduced to the market in 1974. Oilon was the very first authentic lubricated Nylon, havinga blended liquid lubricant system built in during the processstages, which obviously resulted in a substantial increase inbearing life, 5 times that of Natural cast nylon and 25 timesthat of phosphor bronze! The lubricant contained within thematerial will not drain, machine, spin, leech or dry out andnever needs replenishment.

RE-FLEX® 780AJLM is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

RE-FLEX® 1592AJL is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

PAR Group Peek Carbon Filled Sheet maintains all the significant benefits of standard PEEK material such as excellent chemical and radiation resistance, high dimensional stability and high resistance to creep. The carbon fiber reinforcement helps to improve the wear properties of the material as they are typically less abrasive than the fibers used in the glass filled alternative. Carbon filled PEEK sheet is also flame retardant, self-extinguishing and electrically conductive, making for an extremely versatile material.

Petroz™ 390 durometer FFKM with unsurpassed compression set properties while maintaining excellent chemical resistance.

PEEK is a polyetheretherketone materials are suitable for the production of components that are intended for continuous use under the toughest conditions. In addition to a very high continuous service temperature (up to +260°C), PEEK also has extremely high strength and rigidity with good toughness at the same time. In addition, PEEK is characterized by excellent abrasion resistance, excellent sliding properties and a low linear thermal expansion coefficient.

RE-FLEX® 580AXL is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

RE-FLEX® 1588AJL is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

Petroz™ 375 durometer general purpose FFKM with exceptional compression set properties and excellent chemical resistance.

RE-FLEX® 795AS is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

Nylacast H.S Blue is heat stabilized cast nylon, easily distinguished by its blue color. Additives in the form of high temperature resistant colorants, heat stabilizers and UV stabilizers allow HS Blue to better retain its mechanical properties in applications operating at higher temperatures.

Polikim Kestamid®(PA6G-Cast Nylon) is one of the most commonly used engineering plastics.

FLUORONOID® FL 381 is a Acetal – POM Copolymer

RE-FLEX® 790AJL is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

RE-FLEX® 570A is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.