Products in Consumer Goods: Prepreg

HexPly® 996 is a 350ºF (177ºC) curing cyanate siloxane resin with a 330ºF (165ºC) glass transition temperature. Standard cure is two hours at 350ºF (177ºC). HexPly® 996 can be autoclave and press cured. HexPly® 996 can be impregnated on all available fibers and fabrics. The recommended lay-up procedure for HexPly® 996 is HSP-L3. The recommended cure procedure is HSP-C1 or HSP-C6. Typical applications for HexPly® 996 are primary and secondary space structures where the optimum dimensional stability and lowest moisture absorption are required.

Toray Toray AmberTool® HX56 is a low temperature curing epoxy composite tooling prepreg. After a suitable post cure, an end use temperature of 180°C (356°F) is achieved. Toray AmberTool® HX56 achieves an excellent surface finish for small to medium sized autoclave tooling.

Resinoid 1365 is a glass reinforced, two-step phenolic molding compound offering excellent mechanical strength as well as good electrical and thermal characteristics. This material is offered as a moderate size pellet suitable for compression and transfer molding. It can be used in injection molding systems with deep flight screws.

HexPly® 1454 is a self-extinguishing epoxy resin system with very high self adhesion properties. It has good handling and is tolerant of a wide range of processing conditions. HexPly® 1454 is ideal for the fabrication of honeycomb sandwich structures when high peel strength and good impact properties are required. HexPly® 1454 prepregs are only available with fabric reinforcements.

CEM100 is a cyanate ester prepreg designed to cure at medium temperatures, whilst producing durable components with excellent high temperature performance. It can be supplied on a variety of fabrics to meet your cost and manufacturing requirements.

HexPly® 6268 is a modified epoxy resin which provides good adhesion to honeycomb core. It is a selfextinguishing matrix system offering good toughness, which is used for aircraft primary and secondary structures. HexPly® 6268 is available in UD carbon and woven aramid, glass and carbon.

THINPREG™ TP 135 is a breakthrough product combining high strength and high toughness in a thin ply format. The PES-toughened epoxy system shows compression after impact properties typical of 3rd generation aerospace matrices. Thin ply materials achieve higher usable properties from the fiber through spreading load more consistently though the laminate and delaying first ply failure. Negligible ply drop-off effects and greater degrees of freedom in design are now combined with a PES-toughened system for high resolution, highly optimized, super-strong composite structures.

HTC400 is an epoxy resin system designed to cure at 180°C. It is a toughened epoxy resin system designed for demanding, high temperature applications. It can be supplied on a variety of fabrics and in UD format to meet your cost and manufacturing requirements.

7119 PTFE-Glass Fabric is a Premium Grade PTFE-Glass Fabric offers optimum release and durability in harsh environments. Applications include reusable pan liners for cooking and baking, laminate separator sheets, tortilla and pizza crust belts, heat sealing and applications where fabric weave impression is undesirable.

HexPly® 914 is a highly successful modified epoxy matrix which is used extensively in high temperature resistant primary aircraft structures. The controlled melt viscosity and excellent matrix rheology of HexPly® 914 permits a wide range of processing conditions for high quality components.

Toray 8020-FR is a modified epoxy resin system suitable for curing between 70°C (158°F) and 120°C (248°F). The medium viscosity resin is pre impregnated into high performance fibers such as carbon, glass and aramid. Toray 8020-FR offers excellent structural properties, flame retardance and toughness. Toray 8020-FR is designed for structural Applicationss in the motor racing, general industrial fabrications and marine industries and is suitable for a wide range of engineering Applicationss.

IM Carbon Fiber UD125 H60-T1000 GRADE is a E3 Matrix System with a precursor as PAN.

Resinoid 1505 is a milled glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for electrical applications where very low post-molded shrinkage is desired. This material comes in granular form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

LTC102 Prepreg is designed to cure at low temperatures whilst giving the potential for high temperature tooling. It can be supplied on a variety of fabrics to meet your cost and manufacturing requirements.

HexPly® M49 is a 120°C curing toughened epoxy matrix with good impact resistance suitable for use in performance cars. The matrix is highly tolerant to a wide variety of production techniques and equipment making it easy to process. HexPly® M49 is especially suitable for carbon look applications (eg car interiors).

GMS Composites EP – 270 is a formulated epoxy resin matrix prepreg with long out life. The product has a versatile curing cycle from as low as 70°C or as high as 130°C, thus enabling the product to be used to produce a wide range of composite items, from large structures to numerous small components. EP-270 is available in a range of substrates such as carbon, glass or aramid. EP-270 allows faster cycle times at elevated temperatures. The product also has good dynamic strength properties. The prepreg has good flow and the tack of EP-270 can be varied.

HS Carbon Fiber UD300H60 is a E3 Matrix System with a precursor as PAN.

Toray E650 is a low temperature curing toughened resin system pre-impregnated into high performance fibers such as carbon, glass and aramid. It is designed for the production of composite structures in the leisure and sporting industries and also for a range of engineering Applicationss. Toray E650 is compatible for co-cure with Toray’s low temperature cure resin film, Toray EF44, and Toray’s low temperature cure syntactic core, Toray MicroPly™ LT64.

Evopreg® EPT120 tooling prepregs are designed to help composite tooling manufacturers improve the flexibility and efficiency of their tooling manufacturing operations, by providing a combination of extended out-life and flexible curing cycles. With an out-life of 21 days, Evopreg® EPT120 prepregs are ideally suited to the production of larger, more complex tools, or to the batch production of multiple tools, ahead of a single (e.g. Weekly) scheduled cure. For applications where rapid turnaround is critical, Evopreg® EPT120 prepregs can be fully cured in a single-shot ramped cure. The prepregs can be supplied with a range of reinforcement fibers and fabric constructions. They require low pressure autoclave processing for optimum surface finish and are suitable for a range of applications including automotive, motorsport, sporting goods and general industrial.

HexPly® M9.6H is a hotmelt, thermosetting, low tack epoxy resin matrix, specifically designed for prepreg applications at which short cure cycles of 100°C and above are required. M9.6H can be used for manufacture of large industrial components, suitable for cure of thin and thick sections. M9.6H exhibits a long out-life at ambient conditions.

HexPly® M91 is a high performance, very tough epoxy matrix for use in aerospace primary structures and engines. HexPly® M91 is a toughened, controlled flow, epoxy resin system supplied with unidirectional fibers.

HexPly® M36 is a high performance 180 °C cure matrix developed for aerospace and industrial markets. It can be used in a variety of production techniques (Resin Film Infusion (RFI), prepreg and semipreg) making it easy to process. When cured, HexPly® M36 becomes a tough composite with excellent hot/wet performance. Its low density contributes to increased weight savings, and the flexibility in curing gives potential for composite part cost savings.

HexPly® EH25 is a high performance, tough 180°C curing matrix for use in Aerospace primary structures. HexPly® EH25 is a self-extinguishing epoxy resin with controlled flow. HexPly® EH25 prepregs are available with fabric and UD tape.

HS Carbon Fiber UD100H60 is a E3 Matrix System with a precursor as PAN.

HS Carbon Fiber UD150H60 is a E3 Matrix System with a precursor as PAN.

Deltapreg DT197 is a Automotive with heat managment Application.

HexPly® M79/M79-LT is a hotmelt, thermosetting, low-exothermic epoxy resin matrix, specifically designed for prepreg applications at which short cure cycles below 100°C are required. M79/M79-LT can be used for manufacture of large industrial components, suitable for cure of thin and thick sections. M79/M79-LT exhibits a long out-life of 8 weeks at ambient conditions. M79 is supplied as moderate tack and M79-LT as low tack resin matrix.

IM Carbon Fiber UD150H60-MR60H is a E3 Matrix System with a precursor as PAN.

Deltapreg TR43 is a Automotive with tooling Application.

PREGNIT TP-PP is resistant to non-oxidizing Acids and alkalis.

M74 is a high flow, 350°F (177°C) curing epoxy resin with extensive space structural heritage*. M74 is formulated for autoclave processing, but it has been successfully processed by press molding. Unidirectional tape and woven fabric impregnated with M74 resin will retain good tack and drape for at least 10 days at 70°F (21°C). Standard cure is for two hours at 350°F (177°C). Hexcel recommended lay-up procedure is HSP-L1 or HSP-L2. Recommended cure procedure is HSP-C1 or HSP-C2.

Natex P-Preg PLA P1/1 950 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

HexPly® 6376 is a high performance tough matrix formulated for the fabrication of primary aircraft structures. It offers high impact resistance and damage tolerance for a wide range of high temperature applications.

PREGNIT TP-PE has high resistance to acids, Alkalis and chemicals.

I-Speed® laminate and prepreg products are manufactured with Isolas' patentable high performance multi-functional resin system, reinforced with electrical grade (E-glass) glass fabric. This system delivers a 15% improvement in Z-axis expansion and offers 25% more electrical bandwidth (lower loss) than competitive products in this space. These properties coupled with superior moisture resistance at reflow, result in a product that bridges the gap from both a thermal and electrical perspective. The I-Speed® resin system is laser fluorescing and UV blocking for maximum compatibility with Automated Optical Inspection (AOI) systems, optical positioning systems and photo imageable solder mask imaging.

HS Carbon Fiber UD200H60 is a E3 Matrix System with a precursor as PAN.