products in Medical

Kettlitz-Chemie

Kettlitz Chemie Antitack NP-97

Antitack NP-97 is a Pure zinc stearate dispersion of small particles, developed especially for dip tank equipment. The stearate particles are only partially hydrophobic due to the special production process. Therefore the antitack agent within the dilution shows the tendency to rise to the upper third of the dip tank. While the compound leaves the dip tank, it passes through the region of highest concentration and gets the optimum coverage of an-titack agent.

Kraton

Kraton™ D1165 P

Kraton D1165 P is a clear, linear triblock copolymer based on styrene and isoprene with a polystyrene content of 30%. It is supplied from North America in the physical form identified below. Kraton D1165 PT - supplied as a dusted dense pellet Kraton D1165 P is used in compound formulations and as a modifier of thermoplastics. It may also find use in formulating adhesives, sealants, coatings and modified bitumens.

Fainplast Compounds

Hax™ HF 239/3

Quantum Composites

Lytex® 9063-E

Lytex® 9063-E is an epoxy high performance, fiberglass reinforced ESC® molding compound designed for military and aerospace structural applications requiring excellent mechanical properties, retention of properties at elevated temperatures, good chemical resistance and excellent electrical properties. It meets the requirements of MIL-M-46069 and MIL-M-46892.

Kuraray

Kuraray Poval™ 4-88

KURARAY POVAL™ 4-88 by Kuraray is polyvinyl alcohol manufactured by alcoholysis of polyvinyl acetate. It is a water-soluble, partially saponified, odorless polymer. Its aqueous solution can be added to polymer emulsions already stabilized with polyvinyl alcohol which affects the extension of the open time, setting speed and rheology. Applicable for use in remoistenable adhesives. KURARAY POVAL™ 4-88 conforms to EU Directive 67/548/EC.

Elastocon TPE Technologies

Elastocon® 2880L

Elastocon® 2880L thermoplastic elastomer has been developed for applications that require rubber-like properties and a reduced coefficient of friction. Elastocon® 2880L is FDA compliant and well suited for consumer goods and industrial applications. Elastocon® 2880L can be overmolded onto polypropylene.Elastocon® 2880L is supplied as ready to use pellets in 50 lb. bag quantities.

Sanyo Chemical America Incorporated

PELECTRON PVL

PELECTRON PVL is a polymer-alloy type permanent antistatic agent for polyolefin resins (e. g. polyethylene, and polypropylene) which was developed by using an original Sanyo Chemical compatibilization technique. This product imparts a long-lasting antistatic property to polyolefin resins while causing practically no lowering of their physical properties and moldability. This product dry-blended with polyolefin can be directly molded without a kneading process because this product exhibits excellent dispersibility in polyolefin. In addition, compared to conventional permanent antistatic agents, PELECTRON PVL exhibits an excellent antistatic property even when used in small amounts because this product substantially decreases surface resistivity of polyolefin.

United-Guardian, Inc.

Lubrajel® MG

Lubrajel MG is a proprietary hydrojel formulation that was developed in the early 1970's as a non-drying, water-soluble lubricant for the medical industry. Lubrajel MG has been marketed since its development in 1973 as a medical lubricant. It has been used as a general and instrument lubricant for use during physical exams, and applied to catheters, thermometers and a host of other instruments to aid in use and patient comfort.

Dynasol Elastomers

Paracril™ 3335

Paracril 3335 is a copolymer of butadiene and acrylonitrile, cold polymerized with a non-staining stabilizer.

DAK Americas

Array™ 9921M

Array™ 9921M is a Polyethylene Terephthalate (PET) material. It is available in Latin America or North America for stretch blow molding.Important attributes of Array™ 9921M are: Clarity Copolymer Eco-Friendly/Green Food Contact Acceptable Good Processability Typical applications include: Medical/Healthcare Engineering/Industrial Parts Food Contact Applications

NuSil Technology

NuSil™ MED-1511

NuSil™ NuSil™ MED-1511 is a RTV silicone adhesive.

Teijin Limited

Panlite® L-1250Y

Teijin Limited Panlite® L-1250Y is a Polycarbonate (PC) material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for extrusion or injection molding.Important attributes of Panlite® L-1250Y are: Flame Rated Good Mold Release Medium Viscosity

NuSil Technology

NuSil™ MED-361

NuSil™ MED-361 is a NuSil Technology's restricted materials may be considered for use in short-term implant applications, 29 days or less, or for external applications.Fluids are non-curing, stable silicone polymers typically used as lubricants. Fluids are available in a variety of viscosities. Depending on the viscosity, fluids can be applied by spraying, dipping, wiping, or brushing. For optimal performance, the chEMIstry of the fluid should not match the chEMIstry of the substrate being lubricated. If unsure of the compatibility of the substrate and lubricant, contact the supplier of each material for assistance.Because they are so dynamic, fluids can be adapted to perform well in a wide array of projects.Comments: DIMETHYL POLYMER.

NuSil Technology

NuSil™ MED-1037

NuSil™ NuSil™ MED-1037 is a RTV silicone adhesive.

Pinnacle Polymers

Pinnacle™ PP 1635AF

35 MELT FLOW HOMOPOLYMER Pinnacle Polymers Polypropylene 1635AF is made via UNIPOL™ PP technology, which utilizes gas-phase fluidized bed reactors with a high activity catalyst system to ensure uniform physical properties and lot-to-lot consistency.This product is intended for injection molding; the flow properties should be of particular benefit in the production of thin-walled articles. It contains no nucleators, antistats or animal derivatives.Potential applications include: healthcare/medical packaging, labware, containers and thin-wall articles in general.The 1635AF highlights: Heat Sterilizable (autoclavable) Contains no animal derivatives Excellent color and processing stability Low Extractables Pinnacle's polypropylene, as marketed by Pinnacle Polymers Company, in natural, uncolored pellet form complies with appropriate requirements of CFR Title 21, Part 177, Subpart B, Section 177.1520 (c) 1.1a entitled "Olefin Polymers" of the Food Additives Amendment of 1958 to the United States Food, Drug and Cosmetic Act of 1938.

Kraton

Kraton™ D1192 E

Kraton D1192 E is a clear linear block copolymer based on styrene and butadiene with bound styrene of 30% mass. It is supplied from Europe in the physical forms described below: Kraton D1192 ET- supplied as porous pellets dusted with talc Kraton D1192 ES - supplied as porous pellets dusted with amorphous silica Kraton D1192 ESM - supplied as powder dusted with amorphous silica Kraton D1192 ETM - supplied as powder dusted with talc for the North American market Kraton D1192 ETF - supplied as fluffy crumbs dusted with talc Kraton D1192 E is used for modification of industrial and paving bitumen. It may also be suitable for use in formulating adhesives, sealants and coatings, and in the modification of polymers.

VYNOVA

VYNOVA™ S6030

VYNOVA™ S6030 is a low molecular weight, low porosity vinyl chloride homopolymer. It is a general purpose resin suitable for extrusion and calendering of PVC: rigid films for medical, food or consumer goods packaging, compact and foamed sheets, compact and foamed profiles, foam core pipes and fittings, and flooring.

United-Guardian, Inc.

Lubrajel® RR

Lubrajel RR is clear and colorless, and virtually odorless and remains so after sterilization by gamma radiation. An initial apparent viscosity of about 25,000 cps (Brookfield RVT or equivalent, spindle #7, 50 rpm, 22º C) exhibits practically no change upon irradiation. Temperature stressed stability studies indicate that pH, viscosity, color, clarity and lubricating qualities are not sacrificed.

Okamoto Glass Co. Ltd.

Okamoto Glass Co. Ltd. OG461

OG461 is a curing agent which find its applications in screenprinting where a good thermal resistance is required.

Momentive Performance Materials

Tufel™ III 92506

Tufel™ III rubber series are biocompatible(1), two component silicone rubber compounds. 92506 and 92656 are 50 and 65 durometer addition curable silicone elastomers that offer low compression set and high resilience with no post bake required for most applications. The combination of these properties may lead to longer service life in highly mechanical applications. The 92506 and 92656 elastomers can be used to produce extruded and calendered parts with excellent permanent set resistance and should be considered for applications such as peristaltic pump tubing, gaskets and seals.Key Features and Benefits Low compression set Excellent elastic memory Biocompatible(1) No post baking required for most applications Low volatile bases minimize porosity Peroxide-free cure system Broad processing window High output rates Tight surface cure Non-blooming Translucency Low hysteresis Potential Applications Healthcare Consumer Goods General Industrial.

NuSil Technology

NuSil™ MED3-4213

NuSil™ MED3-4213 is a fast-cure silicone adhesive.

Momentive Performance Materials

LIM™ 6050-D2

LIM™ 6050-D2 liquid silicone rubber is a 2-component product formulated for use in liquid injection molding to high performance elastomeric parts. It is clear, but easily pigmentable with Momentive Performance Materials masterbatch colors. LIM6050-D2 offers convenient 1:1 mix ratio, high tear strength, and easy release from molds. Cure time is rapid, generally 10 to 40 seconds (@ 150-205°C) depending upon part size, configuration, and molding temperature.Key Features and BenefitsLIM6050-D2 liquid silicone rubber is distinguished by the following properties: High clarity for excellent visibility Excellent tear strength Convenient 1:1 mix ratio for use with automatic equipment Rapid cure time: 10 to 40 seconds depending upon part size, configuration, and molding temperature Wide range of molding temperatures: 150°C (302°F) to 205°C (400°F) Excellent release from metal molds Potential ApplicationsThe combination of excellent clarity, tear strength and very high tensile strength makes this product suitable for a wide variety of applications. Baby bottle nipples Connector inserts Seals Flexible mounts Valves Sports goggles Masks Health care equipment Camera parts Coating metal rolls.

NuSil Technology

NuSil™ MED-4044

NuSil™ MED-4044 is a low viscosity silicone elastomer.

Elastocon TPE Technologies

Elastocon® STK40

NuSil Technology

NuSil™ MED-6755

NuSil™ MED-6755 is a NuSil Technology's restricted materials may be considered for use in short-term implant applications, 29 days or less, or for external applications.Low consistency elastomers (LCEs) are useful alternatives to liquid silicone rubber (LSR) and high consistency rubber (HCR) for end users who need a low viscosity elastomer which provides other unique properties.LCEs lend themselves to applications that require a pourable, self-leveling silicone. Applications include: encapsulating a device, backfilling a void, potting an electronic component that cannot withstand exposure to high heat, or prototyping a mold.Comments: 1.46 R.I., OPTICALLY CLEAR.

Versalis - A subsidiary of Eni S.p.A

Clearflex® CL D0

Clearflex® CL D0 is a linear low density polyethylene, with antioxidants, characterized by a very low density (VLDPE).This resin is produced with a proprietary technology. Stretch films manufactured with Clearflex CL D0 have high stretchability, outstanding clarity and very high constancy in cling effect.Main ApplicationClearflex CL D0 is recommended as cling agent in stretch film but it is also used for applications in which soft touch and flexibility are required, for the improvement of impact resistance when used as additive in blend with other polyolefins formulated with or without mineral fillers.

Kraton

Kraton™ D1161 J

Kraton D1161 J is a clear linear block copolymer based on styrene and isoprene with bound styrene of 15% mass. It is supplied from Japan in the physical form(s) identified below in the grade nomenclature. Kraton D1161 JSP - supplied as dusted dense pellets Kraton D1161 JS - supplied as dusted crumb Kraton D1161 JU - supplied as undusted crumb Kraton D1161 J is used as an ingredient in formulating adhesives, sealants and coatings. It may also find use as a modifier of bitumen and polymers.

3D Systems

VisiJet® M3 Crystal

An engineered plastic performance for durability and stability ideal for functional testing and rapid tooling applications. This material also provides true plastic look and feel for a vast array of prototyping and end use applications. VisiJet Crystal is USP Class VI certified for approved medical applications.

Momentive Performance Materials

Silopren™ LSR 2670

Silopren™ LSR 2670 is a two-component liquid silicone rubber for injection molding processes. In comparison to Silopren™ LSR 2070, Silopren™ LSR 2670 shows a lower viscosity, improved tear resistance and a higher reactivity. Therefore, it is also possible to reduce the vulcanization temperature while maintaining a standard crosslinking rate. The increased reactivity does not affect the properties of the vulcanizate.Key Features and BenefitsVulcanizates of Silopren™ LSR 2670 are typically distinguished by the following properties: High reactivity, lower viscosity, shorter cycle time Excellent thermal stability Biocompatible Sterilizable with ethylene oxide, steam and gamma radiation High stability and flexibility at low temperatures Good rubber-like properties, high tear resistance Long service life at dynamic stress High stability to ozone and ultraviolet light Outstanding resistance to aging Excellent dielectric behavior over a wide range of temperatures Not readily combustible, does not melt or drip Easily pigmentable with LSR color pastes KTW approved Potential ApplicationsBecause of its outstanding properties, Silopren™ LSR 2670 is an excellent candidate to consider for the following elastomeric articles: Sealing elements O-rings Stoppers Keypads Vibration dampers Pressure cookers parts Spark plug boots, catheters, parts of medical technical equipment s.o.

BARLOG plastics GmbH

Keballoy® 3D FE 170302 PP

Special compound for 3D effect painting based on PP, e.g. B. For decorative applications in the automotive exterior.

NuSil Technology

NuSil™ MED-6607

NuSil™ MED-6607 is a NuSil Technology's unrestricted materials may be considered for long-term implant applications (greater than 29 days)."Dispersion" is a term used to describe a silicone elastomer system that is suspended or dispersed in a solvent carrier. It is a complex solution that contains silicone polymers of various molecular weights and reinforcing fi llers. The substituent groups comprising the polymer back bone structure may consist of the following: Polydimethylsiloxane, Dimethyl Diphenyl copolymer, and Fluoro homo polymer or copolymer. Silicone dispersions typically have low viscosities, which is benefi cial for applications wherein a thin fi lm coating is needed, and they can easily be used in dipping and spraying processes. NuSil uses a variety of solvents to disperse silicones, such as xylene, tert butyl acetate, heptane, hexane, acetone and naphtha.Comments: ONE PART, IN NAPHTHA.

AB Specialty Silicones

Andisil® VS 100

Andisil® Vinyl Polymers are vinyl-terminated dimethylpolysiloxanes that are available in a variety of viscosities. They can be used as base polymers or as blend polymers in order to create the desired hardness. These polymers can be cured with silicon-hydride crosslinkers and a platinum catalyst.

Elastocon TPE Technologies

Elastocon® STK56PA

Elastocon® STK56PA a colorable thermoplastic elastomer that has been developed for applications that require soft rubber-like properties and a good surface finish. Elastocon® STK56PA is well suited for consumer goods and industrial applications requiring non-slip/soft touch ergonomics, sound and vibration dampening, improved impact resistance, and U.V. stability. Elastocon® STK56PA can be overmolded to polyamide/nylon.Elastocon® STK56PA is supplied as ready to use pellets in 50 lb. bag quantities.

Kettlitz-Chemie

Kettlitz Chemie Actigran 70

Mediaplast PM is a synthetic aromatic plasticizer based on polyalkylbenzene (bi- and trialkylated aro-matics), which is mainly recommended for the use in elastomers with low to medium polarity, i. e. NR, IIR, BR, SBR, EP(D)M for example, but also CR, CM/CSM, EVA and PNR. Especially in polychloro-prene the often used, expensive ester plasticizers can be replaced completely.

Quantum Composites

AMC® 8592

AMC® 8592 is a chopped carbon fiber reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 12K tow.

Greene Tweed

Fluoraz™ 890

Fluoraz 890 is formulated for use in sanitary gaskets where both USP and FDA compliance is required, making it an excellent compound for both pharmaceutical and other hygienic fluid handling applications such as seals for brewery applications. Fluoraz 890 metal and TOC extractable are an orde of magnitude lower than premium competitive FKM formulations, ensuring little or no contamination into the process stream. Fluoraz 890 also meets the extrative requirements of both 21 CFR 177.2600 (e), (f) and 21 CFR 177.240 (d) extraction testing for perfluoroelastomers. Fluoraz 890 sanitary gaskets by Greene, Tweed are designed for minimal intrusion.Fluoraz 784 is also available in O-rings and custom shapes where a low durometer hardness is desired.