Power & Utilities

Sika

Epolam 2020

EPOLAM 2020 is a Variable reactivity by addition of an accelerator Tg ~80°C

Polynt Group

ENYDYNE® H 68377 TAE

ENYDYNE® H 68377 TAE - Unsaturated polyester resin in styrene,DCPD. It is used as general purpose in hand lay up and spray up method.

Polynt Group

EPOVIA RF-9000(P)

EPOVIA RF-9000(P) is Bisphenol-A epoxy based vinyl ester resin for primer and it is generally used in Chemical Industry,Industrial sector applicatons

FIBERTEC INC.

MICROGLASS 3004

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Polynt Group

ARMORFLEX® 953

Polynt Composites’ ArmorFlex® 953 Series gel coats are high performance products formulated for the fiberglass industry. They are primarily formulated for marine and sanitary applications,but should be used in any application where water and chemical resistance are needed. ArmorFlex® 953 Series also have exceptional gloss and buffing characteristics. While offering these benefits,the ArmorFlex® 953 Series gel coats have retained the important construction application qualities expected from Polynt Composites gel coats,such as resistance to porosity,tearing,and color separation; sag resistance; consistent liquid properties; excellent patchability; and more. These all add up to higher quality appeal in FRP parts made from Polynt’s ArmorFlex® HIGH GLOSS BUFFBACK® gel coats. ArmorFlex® 953 Series gel coats have enabled customers to meet and surpass all requirements of the American National Standard for plastic bathtubs,shower receptors and shower stalls,ANSI Z124.1,.2 and .3 –1995,Sec. 6.1.1. Gel coats in the 953 Series require only the addition of the proper amount of the appropriate methyl ethyl ketone peroxide to cure. ArmorFlex® HIGH GLOSS BUFFBACK® gel coats are available in the same wide range of colors as other POLYCOR® gel coats. Refer to Polynt’s POLYCOR® Color Card for color selection. Standard base white ArmorFlex® is 953WJ340.

Polynt Group

Polynt Group SMC LS 3800 R25 RF C NERO

Polynt Group SMC LS 3800 R25 RF C NERO is a sheet molding compound based on an unsaturated polyester resin, fire retardant grade, reinforced with glass fibers. SMC LS 3800 R25 RF C NERO has been developed for application where is requested anti-static protection SMC LS 3800 R25 RF C NERO joint good mechanical properties mainly for impact resistance. SMC LS 3800 R25 RF C NERO is formulated according to RoHS, REAC regulation SVHC and WEEE European legislation.

Polynt Group

EPOVIA OPTIMUM® KRF 1001 TAS

EPOVIA OPTIMUM® KRF 1001 TAS - Bisphenol-A Epoxy Resin based vinyl ester in styrene. It is used to produce pipes and tanks through hand lay up and spray up method.

Hexcel

HexTow® AS4

HexTow® AS4 carbon fiber is a continuous, high strength, high strain, PAN based fiber available in 3,000 (3K), 6,000 (6K) and 12,000 (12K) filament count tows. This fiber has been surface treated and can be sized to improve its interlaminar shear properties, handling characteristics, and structural properties, and is suggested for use in weaving, prepregging, filament winding, braiding, and pultrusion. AS4-GP 3k (1%), AS4-GP 12k (0.9%), and AS4 12k carbon fibers have been qualified to NMS 818 Carbon Fiber Specification (NCAMP). This allows customers to call out an industry standard, aerospace grade carbon fiber without the need to write and maintain their own specification.

Sika

Biresin® CR131

Biresin® CR131 is an epoxy resin system suitable for the production of high performance fiber reinforced composites parts and molds with thermal properties up to 130°C.

FIBERTEC INC.

MICROGLASS 7204

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

FIBERTEC INC.

MICROGLASS 3016

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Hexcel

HexTow® IM2A

HexTow® IM2A carbon fiber is a continuous, high performance, intermediate modulus, PAN based fiber available in 12,000 (12K) filament count tows. This fiber has been surface treated and can be sized to improve its interlaminar shear properties, handling characteristics, and structural properties. It is suggested for use in prepregging, filament winding, braiding, and pultrusion. The unique properties of HexTow® IM2A fiber, such as higher tensile strength and modulus, as well as good shear strength, allow structural designers to achieve both higher safety margins for both stiffness and strength critical applications. HexTow® IM2A is International Monohull Open Class Association (IMOCA) certified/qualified.

Sika

Biresin® CR201

Biresin® CR201 is a three component, anhydride cured, low viscosity epoxy resin system suitable for the production of high performance fi bre reinforced composites with outstanding heat resistance.

Munzing

FOAM BAN® 149

FOAM BAN® 149 is a defoamer formulated with silicone compounds dispersed in synthetic hydrocarbons for use in non-aqueous industrial lubricants. The main areas of applications are hydraulic oils and gear oils.

Polynt Group

DISTITRON® 5119 ESX20Q

DISTITRON® 5119 ESX20Q - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce reinforced plastics,general purpose through hand lay up and spray up method.

Sika

Biresin® CR144

Biresin® CR144 is a three component, anhydride cured, low viscosity epoxy resin system suitable for the production of high performance fi bre reinforced composites.

Polynt Group

NORSODYNE® H 84233 L

NORSODYNE® H 84233 L - Unsaturated polyester resin in styrene,halogenated. It is used to produce building panels,parts with high resistance to fire through hand lay up and spray up,continuous laminating method.

Polynt Group

NORSODYNE® T 16372

NORSODYNE® T 16372 - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce building panels,isothermal sandwich panels through continuos laminating method.

Polynt Group

NORSODYNE® O 12335 AL

NORSODYNE® O 12335 AL - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce inclusion through casting method.

FIBERTEC INC.

MICA 20S

Mica Is A Generic Term Applicable To The Group Of Complex Aluminosilicate Minerals That Occur Naturally In Plate Or Sheet-Like Form.

FIBERTEC INC.

MICROGLASS 7216

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

FIBERTEC INC.

MICROGLASS 7232

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Polyumac

Polyumac Air-Cell T-60

Polyumac Air-Cell T-60 is a hybrid, closed cell cross-linked polyester foam core that is an economical alternative to other cores used in the production of sandwich composite structures. In addition to its excellent strength to weight ratio, it offers good dimensional stability at elevated temperatures.

Polynt Group

DISTITRON® 510 V5

DISTITRON® 510 V5 - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce flat sheets,laminates,transparent and corrugated sheets through continuous laminating method.

Polynt Group

DISTITRON® 3519 A

DISTITRON® 3519 A - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce production of gelcoat through mix with fillers and/or additives.

Zoltek

ZOLTEK™ PX35 UD200

ZOLTEK PX35 Stitch-Bonded Uni-Directional Carbon Fabrics are produced from our ZOLTEK PX35 50K Continuous Tow Carbon Fiber. Unique fiber spreading techniques are utilized to obtain a wide range of UD fabric weights for a varied set of composite part applications. Quick composite part build-up is cost effectively achieved with our diverse weight range of low-cost carbon fabric products.

3B Fibreglass

3B Fibreglass MF 01 ER

3B Fiberglass MF 01 ER are E-CR glass filaments ground to a specified density. MF 01 ER is designed to reinforce products like thermoplastics, thermoset resins, glues, coatings, and adhesives within a large range of applications and markets.MF 01 ER represents a main improvement compared to minerals when aiming for a higher stiffness and/or better impact properties in combination with specific properties, such as flow enhancement, flame retardancy, uniform isotropic shrinkage, resistance to acid environment, coating stability, etc. MF 01 ER can be collocated in between mineral fillers and most com-monly available milled fibers as it dis-plays an intermediate length/diameter aspect ratio. The product comes in a powdery form that provides both improved flowability/handling and low density.

Hexcel

HexTow® IM2C

HexTow® IM2C carbon fiber is a continuous, high performance, intermediate modulus, PAN based fiber available in 12,000 (12K) filament count tows. This fiber has been surface treated and can be sized to improve its interlaminar shear properties, handling characteristics, and structural properties. It is suggested for use in prepregging, filament winding, braiding, and pultrusion. The unique properties of HexTow® IM2C fiber, such as higher tensile strength and modulus, as well as good shear strength, allow structural designers to achieve both higher safety margins for both stiffness and strength critical applications. HexTow® IM2C is International Monohull Open Class Association (IMOCA) certified/qualified.

Polynt Group

NORSODYNE® S-9211CT

Norsodyne® S-9211CT is filled resin, NF P92-507 and NFF 16-101 standard approved: M2 F2 and it is generally used in industrial sector, marine, mass transports, railway sector applicatons.

Polynt Group

NORSODYNE® O 13155 AL

NORSODYNE® O 13155 AL - Unsaturated polyester resin in styrene,Orthophthalic. It is used in hand lay up and spray up method.

Hexcel

HexTow® IM7

HexTow® IM7 carbon fiber is a continuous, high performance, intermediate modulus, PAN based fiber available in 12,000 (12K) filament count tows. This fiber has been surface treated and can be sized to improve its interlaminar shear properties, handling characteristics, and structural properties. It is suggested for use in weaving, prepregging, filament winding, braiding, and pultrusion. The unique properties of HexTow® IM7 fiber, such as higher tensile strength and modulus, as well as good shear strength, allow structural designers to achieve both higher safety margins for both stiffness and strength critical applications. IM7-G 12K (0.25%) carbon fiber has been qualified to NMS 818 Carbon Fiber Specification (NCAMP). This allows customers to call out an industry standard, aerospace grade carbon fiber without the need to write and maintain their own specification.

Polynt Group

ARMORFLEX® 99F

ArmorFlex® 99F gel coats are advanced technology polyesters that have been formulated for the fiberglass industry. ArmorFlex® 99F gel coats have lower volatile organic compounds (VOC’s) than standard gel coats.

Polynt Group

NORSODYNE® H 36338 TA

NORSODYNE® H 36338 TA - Unsaturated polyester resin in styrene,Isophthalic. It is used to produce pipes and tanks,pools through hand lay up and spray up method.

Polynt Group

NORSODYNE® VUP-1510

Norsodyne® VUP-1510 - for low profile systems, class a. It is generally used in industrial sector applicatons.

Polynt Group

RECarbon® 90CFP40-400gr

RECarbon® 90CFP40-400gr - Recycled molding compound based on epoxy resin and reinforced with reinforced with pyrolized carbon fleece designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Polynt Group

OPTIMOLD ll MONOCOMPOSANT

OPTIMOLD ll MONOCOMPOSANT - Mold construction. 24 hr turnaround,allows better rigidity and tool life. Use with Polycor Tooling gelcoat and skin coat. Main Applications areas are Building and Construction,Electronic and Electrical,Home and Domestic Applications,Industrial sector,Mass Transports,Railway Sector etc.