Paints & Coatings

INVISTA

Dytek® A

DYTEK® A amine (2-methylpentamine-1,5-diamine) is a methyl branched diamine with differential reactivity of each amine group that allows for crystallinity disruption in various applications such as high temperature nylon and polyamides, polyurethane chain extenders, and epoxy hardeners. It is also used in applications such as water treatment, corrosion inhibition, and metalworking fluids where amine functionality and pH control are important. DYTEK®A has 93% recycle content. It is also used in applications such as water treatment, corrosion inhibition,and metalworking fluids where amine functionality and pH control are important.DYTEK®A has 93% recycle content.

INVISTA

Dytek® BHMT

DYTEK® BHMT (bis-hexamethylene triamine) is a long chain triamine that is used as a binder in asphalt, as a phosphonate scavenger and flocculant in oil & gas applications, and as a hardener in epoxy coating and adhesive applications.

DKSH

Luna-cure PACM-20

Luna-cure PACM is a cycloaliphatic diamine. Luna-cure PACM is mainly used as a hardener for epoxies. The curing of epoxy resins at high temperatures leads to excellent mechanical properties and good resistance against alkalis, acids, hydrocarbon solvents and water. This product is available in Europe, Asia and North America.

INVISTA

Dytek® BHMT-HP

DYTEK® BHMT HP (bis-hexamethylene triamine) is a high purity (>95%) triamine that is used in applications where purity is critical such as phosphonate scavenger and flocculant in oil & gas applications and as a hardener in epoxy coating and adhesive applications.

INVISTA

Dytek® HMD

DYTEK® HMD (hexamethylene diamine) is a highly pure (>99.9%) aliphatic diamine. DYTEK® HMD is used in the production of Nylon polymers, isocyanates, polyamide resins and adhesives. Other applications include water treatment, UV stabilizers, scale and corrosion inhibitors, and petroleum additives. This product is available as an anhydrous that is solid at room temperature and can be shipped as a warm liquid or diluted aqueous solution.

Olin Corporation

D.E.H.™ 35

D.E.H.™ 35 - Tertiary amine accelerator based on 2,4,6-tris-(N,N-Dimethyl-aminomethyl)-Phenol. Suitable as accelerator in low temperarure curing systems or other for non-decorative epoxy applications (primers, mortars, composites,….).

Incorez Ltd

Amirez 148/024

When your application calls for a general purpose hardener at low temperatures, Amirez 148/024 exceeds all performance expectations, meeting every specification requirement with speed and a greater degree of technical excellence. This low viscosity, fast cure waterborne reactive polyamide adduct has all application angles covered, from floor and wall painting to hygiene coatings.

Okamoto Glass Co. Ltd.

Okamoto Glass Co. Ltd. OG461

OG461 is a curing agent which find its applications in screenprinting where a good thermal resistance is required.

Vencorex

Easaqua™ XL 600

Easaqua™ XL 600 is a self emulsifiable, ready-to-use and fast drying hardener, for high performances 2K waterborne Polyurethane formulations..

Olin Corporation

D.E.H.™ 29

D.E.H. 29 Epoxy Curing Agent is an economical, liquid, complex mixture of linear, branched and cyclic ethylene amines. D.E.H. 29 Epoxy Curing Agent offers more flexibility versus DETA,TETA, and TEPA type materials. It is recommended for epoxy coal tar systems, patch kits, two-pack adhesives, and other applications where color is not a limitation. In adhesives,D.E.H. 29 Curing Agent yields much higher peel strength than DETA or TETA at comparable gel times and lower cost.

allnex

BECKOPOX™ EH 606

BECKOPOX™ EH 606 is an aliphatic polyamine adduct. It's a relatively low viscous hardener which can be used with liquid solvent-free epoxy resins.

Olin Corporation

D.E.H.™ 4147

Offer very good UV-stability with only a low tendency to yellowing. Especially suitable for color quartz and paints

Gabriel Performance Products

CAPCURE® 3830-81

CAPCURE® 3830-81 is a medium viscosity, catalyzed mercaptan epoxy curing agent designed specifically for rapid cure in the 3 to 5 minute range at room temperature. CAPCURE® 3830-81 may be used both, as a sole curing agent or as an accelerator for amine and amide or amido-amine curative chemistries. The fast-set characteristics of this product over a wide temperature range (30 °F to 100 °F) offers utility in industrial, coatings, civil engineering and fast-set adhesive application areas.

Olin Corporation

D.E.H.™ 488

D.E.H.™ 488 - Low viscosity, curing agent for liquid epoxy resins. Good blush resistance and general chemical resistance. D.E.H.TM 488 Epoxy Curing Agent is a low viscosity, modified cycloaliphatic polyamine based, curing agent for epoxy resins.

Undesa

Kemfluid 220-G

Kemfluid 220-G is a fatty amide, used as an anti-static and pigment dispersion agent. Hardening agent for paints, lacquers, asphalts, etc. In PVC used for calendering or blown film extrusion. Lubricant for ABS, polystyrene, acrylnitrile styrene, polystyrene and polypropilene pigment dispersion agent.

Incorez Ltd

Aldirez A

Bubbling. It’s a problem which pops up time and time again, particularly in areas subject to low temperature and high humidity levels. Fortunately, under these conditions, Aldirez A provides the ability to create primers that remain remarkably resilient and bubble-free. In addition to its exceptional ability to inhibit CO2 generation, formulators are able to accelerate the cure of PU primers, to improve turnaround efficiency, whilst retaining a workable pot life.

Gabriel Performance Products

Gabepro® GPM-800 LO

GABEPRO® GPM-800LO is a mercaptan (SH) terminated liquid curing agent which imparts rapid-cure characteristics to epoxy resins in combination with selected amines. These systems are unique in that they also provide rapid cure rates at low temperatures and in thin films. GPM-800LO is formulated to have an improved odor relative to our standard product.

Olin Corporation

D.E.H.™ 52

D.E.H.52 Epoxy Curing Agent is a viscous aliphatic polyamine epoxy adduct curing agent. D.E.H. 52 Epoxy Curing Agent combines polyamine properties such as short pot life and rapid cure at room temperature with those of typical polyamide curing agents including easy handling, convenient viscosity and mixing rates with liquid epoxy resins, However D.E.H. 52 Curing Agent is much less hygroscopic than standard polyamines. D.E.H. 52 Epoxy Curing Agent is extremely reactive with liquid epoxy resins at room temperature and is used in the maintenance paints, in two-pack adhesives, civil engineering, castings and hand lay-up laminates. D.E.H. 52 Curing Agent is particularly suitable for colorless coatings or adhesive systems.

Olin Corporation

D.E.H.™ 26

D.E.H.26 Curing Agent is an economical liquid aliphatic polyamine hardener, tetraethylenepentamine (TEPA), that offers a short pot-life and cures in minutes with standard unmodified liquid epoxy resins. Similar to D.E.H. 24 Epoxy Curing Agent in application, it provides lower vapor hazard to workers due to its higher boiling point. D.E.H. 26 Epoxy Curing Agent is used for maintenance paints, the manufacture of epoxy-amine adducts, in adhesives, and civil engineering applications. It is also used as an accelerator for polyamide curing agents. In electrical applications, D.E.H. 26 Curing Agent is used for casting, potting and encapsulation.

Olin Corporation

D.E.H.™ 20

D.E.H. 20 Epoxy Curing Agent is an economical, liquid diethylenetriamine (DETA) aliphatic polyamine hardener that provides a short pot-life and cures in minutes with standard unmodified liquid epoxy resins. D.E.H. 20 Epoxy Curing Agent is used for civil engineering applications, maintenance paints, and in the manufacture of epoxy-amine adducts. It is also used in adhesives, epoxy composite applications and as an accelerator for polyamide curing agents. In electrical applications, D.E.H. 20 Epoxy Curing Agent is used for casting, potting and encapsulation.

Olin Corporation

D.E.H.™ 1450

D.E.H.™ 1450 - Excellent adhesion on critical (badly prepared or wet/humid) substrates. Contains Alkyl phenol

Olin Corporation

D.E.H.™ 4043

offer good color and light stability, as well as tack-free surfaces and an excellent early water resistance. D.E.H.™ 4702 has similar performance properties but is nonyl phenol free.

Vencorex

Easaqua™ X D 803

Easaqua™ X D 803 is a self emulsifiable, ready-to-use and fast drying hardener, for high performances 2K waterborne PU formulations.

IGM Resins

Omnirad 2100

Omnirad 2100 is a highly efficient liquid curing agent to initiate radical polymerization of unsaturated resins after exposure to UV light such as those based on a prepolymer – e.g., acrylates and unsaturated polyesters – in combination with mono- or multifunctional monomers as reactive thinners. It is well suitable for formulations in which Omnirad TPO is used. Omnirad 2100 provides all the handling advantages of a liquid product. In thicker coatings Omnirad 2100 offers improved bottom curing compared with that of Omnirad TPO. It is especially suitable for white-pigmented formulations with minimal yellowing after curing and for coatings with low pigment volume concentration. Therefore Omnirad 2100 can be offered in almost all applications as a one-to-one replacement for Omnirad TPO with certain advantages.

Georgia-Pacific Chemicals

GP 2056

GP® 2056 epoxy hardener is a flake phenolic novolac resin developed by Georgia-Pacific Chemicals as a curing agent for epoxy resins in oilfield, molding compounds, coatings, copper clad laminates, and electrical applications.

DKSH

Luna-cure PACM-50

Luna-cure PACM is a cycloaliphatic diamine. Luna-cure PACM is mainly used as a hardener for epoxies. The curing of epoxy resins at high temperatures leads to excellent mechanical properties and good resistance against alkalis, acids, hydrocarbon solvents and water. This product is available in Europe, Asia and North America.

Georgia-Pacific Chemicals

GP 2074

GP® 2074 is a phenolic novolac resin used as a curing agent for epoxy resins in molding compounds, copper clad laminates, coatings, and electrical applications.

Vencorex

Easaqua™ M 502

Easaqua™ M 502 is a versatile self-emulsifiable aliphatic polyisocyanate, used to prepare crosslinker of high performance two-pack (2K) waterborne polyurethane coatings. As it is solvent-free, it allows a large choice of organic solvents to optimize the parameters of the formulation.

Olin Corporation

D.E.H.™ 487

D.E.H.™ 487 - Longer pot-life version of D.E.H. 488 curing agent

Gabriel Performance Products

RoyOxy® RAC 9544

Polyamide curing agent. It is solvent-free and displays good adhesion and toughness. It is designed for coatings, adhesives, casting, potting and other general purpose applications.

Reichhold

EPOTUF® 37-618

EPOTUF® 37-618 is a solution of 37-615, a polyamide curing agent based on dimerized fatty acids and polyethylene amines for room temperature curing of EPOTUF® solid epoxy resins.

Olin Corporation

D.E.H.™ 625

Modified amine curing agent with extreme high reactivity at low T °C and high chemical resistance. Suitable for chemical anchoring, impregnation/primer on concrete and as co-accelerator.

Gabriel Performance Products

Gabepro® GPM-800

GABEPRO® GPM-800 is a mercaptan (SH) terminated liquid curing agent which imparts rapid-cure characteristics to epoxy resins in combination with selected amines. These systems are unique in that they also provide rapid cure rates at low temperatures and in thin films.

Olin Corporation

D.E.H.™ 90

Phenolic curing agent for fast cure combined with superior adhesion unD.E.R.™ humid conditions.

IGM Resins

Omnirad 2022

Omnirad 2022 is a highly efficient liquid curing agent that is used to initiate radical polymerization of unsaturated resins after exposure to UV light. Omnirad 2022 is the first choice for use in pigmented formulations of all colors, for curing of thick sections or for UV-stabilized clear coatings. Unsaturated resins that are particularly suitable are those based on a prepolymer – e.g., acrylates or unsaturated polyesters – in combination with mono- or multifunctional monomers as reactive diluents. Omnirad 2022 is a photoinitiator mixture with well-balanced surface and through cure.

Olin Corporation

D.E.H.™ 512

D.E.H.TM 512 Epoxy Curing Agent is a modified aliphatic amine that is particularly useful as an accelerator of other amines and polyamides. It is also a fast-setting and low temperature curing agent for liquid epoxy resins. It should be used when good flexibility is required.