Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- HRAC/WSSA Group
- Agrochemical Functions
- Technologies
- Product Families
- Composition
ACTIVE INGREDIENT -
Glyphosate in the form of its diammonium salt - 49.6%
OTHER INGREDIENT - 50.4%
Features & Benefits
- Product Information
READ ENTIRE LABEL BEFORE USING THIS PRODUCT.DO NOT APPLY THIS PRODUCT USING AERIAL SPRAY EQUIPMENT EXCEPT UNDER CONDITIONS AS SPECIFIED WITHIN THIS LABEL.
Product Description: This product is a post-emergence systemic herbicide with no soil residual activity. It is generally non-selective and gives broad spectrum control of many annual and perennial weeds, woody brush, trees and vines. It is formulated as a water soluble liquid and may be applied using most standard industrial or field sprayers after dilution and thorough mixing with water or other carriers according to label directions.
Time to Symptoms: This product moves through the plant from the point of foliage contact to and into the root system. Visible effects are gradual wilting and yellowing of the plant that advances to complete browning of above ground growth and deterioration of underground plant parts. Effects are visible on most annual weeds within 2 to 4 days but on most perennial weeds, effects might not be visible for 7 or more days after application. Extremely cool or cloudy weather following application could slow activity of this product and delay development of visual symptoms.
Stage of Weeds: Annual weeds are easiest to control when they are small. Best control of most perennial weeds is obtained when this product is applied at late growth stages approaching maturity. Refer to the “WEEDS CONTROLLED” section for more information on controlling specific weeds.Always use the higher specified application rate when weed growth is heavy or dense or when weeds are growing in an undisturbed (non-cultivated area). Reduced weed control could result when this product is applied to weeds that show signs of disease or insect damage, are heavily covered with dust or are surviving under poor growing conditions.
Cultural Considerations: Reduced weed control could result when this product is applied to annual or perennial weeds that have been mowed grazed or cut and have not been allowed to regrow to the specified stage prior to application.
Rainfastness: Heavy rainfall soon after application could wash this product off the foliage, thus, a second application might be required for adequate control.
Spray Coverage: For best results, spray coverage must be uniform and complete. Do not spray foliage to the point of runoff.
Mode of Action: The active ingredient in this product inhibits an enzyme found only in plants and microorganisms that is essential to the formation of specific amino acids.
Soil Activity: This product has no soil activity, thus, weeds must be emerged at the time of application to be controlled by this product. Weed seeds in the soil will not be affected by this product and will continue to germinate. Plants arising from unattached underground rhizomes or rootstocks of perennials that have not yet emerged at the time of application will not be affected by this product and will continue to grow.
Degradation: Degradation of this product is primarily a biological process carried out by soil microbes.
Maximum Application Rates: The maximum application rates stated throughout this label are given in units of volume (fl. ozs. or qts.) of this product per acre. However, the maximum allowed application rates apply to this product combined with the use of any and all other herbicides containing the active ingredient Glyphosate whether applied separately or in a tank-mixture on a basis of total pounds of Glyphosate (acid equivalents) per acre. If more than one Glyphosate containing product is applied to the same site within the same year, ensure that the total use of Glyphosate (pounds acid equivalents) does not exceed the maximum allowed. See the “INGREDIENTS” section of this label for necessary product information.
Except otherwise specified in a crop section of this label, the combined total application of this product on a site must not exceed 169.6 fluid ounces (5.3 qts.) equivalent to 6 pounds of Glyphosate acid per acre per year. For applications on Non-crop sites or on Tree, Vine or Shrub crop production sites, the combined total application of this product must not exceed 224 fluid ounces (7 qts.) equivalent to 8 pounds of Glyphosate acid per acre per year.
Applications & Uses
- Markets
- Applications
- Applicable Crop
- Application Technique
- Herbicide Target Species
- Direction For Use
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. This product can only be used in accordance with the directions for use on this label or in separately published supplemental labeling. Do not apply this product in a way that will contact workers or other persons, either directly or through drift. Only protected handlers may be in the area during application. For any requirements specific to your State or Tribe, consult the agency responsible for pesticide regulation.
Unless otherwise directed in supplemental labeling, all applicable directions, restrictions, precautions and conditions of sale and warranty are to be followed. This labeling must be in the user’s possession during application.
- Agricultural Use Requirements
Use this product only in accordance with its labeling and with the Worker Protection Standard (WPS), 40 CFR Part 170. This standard contains requirements for the protection of agricultural workers on farms, forests, nurseries, greenhouses and handlers of agricultural pesticides. It contains requirements for training, decontamination, notification and emergency assistance. It also contains specific instructions and exceptions pertaining to the statements on this label about Personal Protective Equipment (PPE) and Restricted Entry Interval (REI). The requirements in this box only apply to uses of this product that are covered by the WPS.
Do not enter or allow worker entry into treated areas during the REI of 4 hours.
PPE required for early entry to treated areas that is permitted under the WPS and that involves contact with anything that has been treated, such as plants, soil or water is: Coveralls, chemical-resistant gloves made of any waterproof material, and shoes plus socks.
- Non-Agricultural Use Requirements
The requirements in this box apply to uses of this product that are NOT within the scope of the Worker Protection Standard for Agricultural Pesticides (40 CFR Part 170). The WPS applies when this product is used to produce agricultural plants on farms, forests, nurseries, or greenhouses.
Do not enter or allow others to enter until sprays have dried.
Properties
- Formulation Type
Safety & Health
- Precautionary Statements
Hazards to Humans and Domestic Animals
CAUTION: Causes moderate eye irritation. Avoid contact with eyes or clothing. Wear protective eyewear. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum, using tobacco or using the toilet. Prolonged or frequently repeated skin contact may cause allergic reactions in some individuals.
PERSONAL PROTECTIVE EQUIPMENT (PPE):
Some of the materials that are chemical-resistant to this product are listed below.
Applicators and handlers must wear:
- Long-sleeved shirt and long pants
- Chemical resistant gloves (except for pilots) such as barrier laminate, butyl rubber ≥ 14 mils, nitrile rubber ≥ 14 mils, neoprene rubber ≥ 14 mils, viton ≥ 14 mils
- Shoes plus socks
- Protective eyewear
“ENGINEERING CONTROLS” for additional requirements. Follow the manufacturer’s instructions for cleaning and maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
- User Safety Recommendations
Users should:
1) Wash hands thoroughly before eating, drinking, chewing gum, using tobacco or using the toilet.
2) Remove clothing/ PPE immediately if pesticide gets inside. Then wash thoroughly and put on clean clothing.
3) Remove PPE immediately after handling this product. Wash the outside of gloves before removing. As soon as possible, wash thoroughly and change into clean clothing.
- Environmental Hazards
Do not apply directly to water or to areas where surface water is pres-ent or to intertidal areas below the mean high water mark. Do not ap-ply when weather conditions favor drift from areas treated. Do not con-taminate water when disposing of equipment washwater or rinsate.
- Physical And Chemical Hazards
Spray solutions of this product should be mixed, stored and applied using only stainless steel, fiberglass, plastic or plastic-lined steel containers. DO NOT MIX, STORE OR APPLY THIS PRODUCT OR SPRAY SOLUTIONS OF THIS PRODUCT IN GALVANIZED STEEL OR UNLINED STEEL (EXCEPT STAINLESS STEEL) CONTAINERS OR SPRAY TANKS. This product or spray solutions of this product react with such containers and tanks to produce hydrogen gas which may form a highly combustible gas mixture. This gas mixture could flash or explode, causing serious personal injury, if ignited by open flame, spark, welder's torch, lighted cigarette or other ignition source.
Packaging & Availability
- Packaging Type
Storage & Handling
- Storage And Disposal
Do not contaminate water, food or feed by storage or disposal.
PESTICIDE STORAGE: Store in original container in secured dry storage area. Prevent cross-contamination with other pesticides and fertilizers. Do not store above 100ºF for extended periods of time. Storage below 20ºF may result in formation of crystals. If product crystallizes, store at 50ºF to 70ºF and agitate to re-dissolve crystals. If container is damaged or spill occurs, use product immediately or dispose of product and damaged container as indicated below.
PESTICIDE DISPOSAL: Pesticide wastes are toxic. Improper disposal of excess pesticide, spray mixture or rinsate is a violation of Federal law. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency or the Hazardous Waste Representative at the nearest EPA Regional Office for guidance.
CONTAINER HANDLING:
Nonrefillable Container (rigid material; < 5 gallons): Nonrefillable container. Do not reuse or refill this container. Offer for recycling, if available. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container one-fourth full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Drain for 10 seconds after the flow begins to drip. Repeat this procedure two more times. Then offer for recycling if available or puncture and dispose of in a sanitary landfill or by incineration.
Nonrefillable Container (rigid material; > 5 gallons up to < 250 gallons): Nonrefillable container. Do not reuse or refill this container. Offer for recycling, if available. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container one-fourth full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank or store rinsate for later use or disposal. Repeat this procedure two more times. Then offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration.
Refillable Container (≥ 250 gallons & Bulk): Refillable container. Refill this container with pesticide only. Do not reuse this container for any other purpose. Cleaning the container before final disposal is the responsibility of the person disposing of the container. Cleaning before refilling is the responsibility of the refiller. To clean the container before final disposal, empty the remaining contents from this container into application equipment or mix tank. Fill the container about 10% full with water. Agitate vigorously or recirculate water with the pump for 2 minutes. Pour or pump rinsate into application equipment or rinsate collection system. Repeat this rinsing procedure two more times. Then offer for recycling if available or puncture and dispose of in a sanitary landfill, or by incineration or by other procedures approved by state and local authorities.