Company logo

Products

DuPont
Healthcare & Pharma
Applications
Medical
Pharmaceutical Manufacturing
Drug Delivery & Care Solutions
218 products found on DuPont in Healthcare & Pharma .
With TDS
Hide Blends
Hytrel® 6356 product card banner

DuPont

Hytrel® 6356

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion

End Uses: Fuel Tanks, Gears, Hoses, Cosmetic Packaging, Appliances, Pipes, Cables, Automotive Applications, Corrugated Pipe, Monofilaments, Sporting Goods, Thermoforming Applications, Wires, Tubing, Electrical/Electronic Applications, Office Automation Equipment

Density: 1220.0 - 1220.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 290.0 - 290.0 MPa

Hytrel® 6356 is a medium modulus grade with nominal hardness of 63D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Hose and tubing, mandrels, wire and cable, film, profiles, seals, gears, sprockets, fuel tanks, containers with good permeation resistance to gases and liquids.

Hytrel® 7246 product card banner

DuPont

Hytrel® 7246

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Thermoforming, Extrusion, Film Extrusion, Casting, Injection Molding

End Uses: Hoses, SRS Pretensioner, Automotive Safety Retractor, Cable Jacketing, SRS Airbag, SRS Actuator, Sporting Goods, Wires, Electrical/Electronic Applications, Office Automation Equipment, Automotive Safety, Cast Films, Cosmetic Packaging, Appliances, Pipes, Cables, Automotive Applications, Corrugated Pipe, SRS Adjuster, SRS Seatbelt, Connectors, Monofilaments, Film, Safety Restrain System, EV Charger, Automotive Safety Pushbutton, Thermoforming Applications, Tubing, SRS Pillar Loop, Safety Equipment, Signal Cord

Density: 1260.0 - 1260.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 550.0 - 550.0 MPa

Hytrel® 7246 is a high modulus grade with nominal hardness of 72D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.The 72 Shore D hardness is based on a legacy method and is still used for grade identification purposes.Typical applications:Tubing, wire and cable jackets, gears and sprockets, oil field parts.

Hytrel® 4556 product card banner

DuPont

Hytrel® 4556

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Coating

End Uses: Belts/Belt Repair, Hoses, Cosmetic Packaging, Appliances, Crates, Automotive Applications, Containers, Cable Jacketing, Hose Jackets, Film, Sporting Goods, Thermoforming Applications, Tubing, Electrical/Electronic Applications, Office Automation Equipment, Cast Films

Density: 1140.0 - 1140.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 87.0 - 87.0 MPa

Hytrel® 4556 is a medium modulus grade with nominal hardness of 45D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.

Hytrel® 5556 product card banner

DuPont

Hytrel® 5556

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Coating, Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion

End Uses: Cast Films, Hoses, Cosmetic Packaging, Appliances, Pipes, Cables, Automotive Applications, Corrugated Pipe, Monofilaments, Cable Jacketing, Sporting Goods, Thermoforming Applications, Wires, Tubing, Electrical/Electronic Applications, Office Automation Equipment

Density: 1190.0 - 1190.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 190.0 - 190.0 MPa

Hytrel® 5556 is a medium modulus Hytrel® grade with nominal durometer hardness of 55D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Hose and tubing, wire and cable, film and sheeting, belting.

Delrin® Sc698 Nc010 product card banner

DuPont

Delrin® SC698 NC010

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding

Additives Included: Mold Release Agent

Flexural Modulus: 3000.0 - 3000.0 MPa

Common features of Delrin® acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance, as well as resistance to moisture, gasoline, lubricants, solvents, and many other neutral chemicals. Delrin® acetal resins also have excellent dimensional stability and good electrical insulating characteristics. They are naturally resilient, self-lubricating, and available in a variety of colors and speciality grades. Delrin® acetal resin typically is used in demanding applications in the automotive, domestic appliances, sports, industrial engineering, electronics, and consumer goods industries. Delrin® SC698 NC010 is a lubricated low viscosity acetal homopolymer, developed for high precision thin-walled parts requiring low wear and low friction with excellent surface aspect.

Hytrel® 3078 product card banner

DuPont

Hytrel® 3078

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Blow Molding, Casting, Injection Molding, Compounding, Calendering, Extrusion, Coating

End Uses: Cosmetic Packaging, Appliances, Cables, Automotive Applications, Film, Sporting Goods, Thermoforming Applications, Wires, Tubing, Electrical/Electronic Applications, Office Automation Equipment, Cast Films

Density: 1070.0 - 1070.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 27.0 - 27.0 MPa

Hytrel® 3078 is a very low modulus grade, with nominal hardness of 30D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Food compliance:Refer to Hytrel® 3078FGTypical applications:Compounding, extrusion, injection molded and over-molded parts for consumer use.

Hytrel® 8238 product card banner

DuPont

Hytrel® 8238

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion

End Uses: Cast Films, Gears, Hoses, Cosmetic Packaging, Appliances, Pipes, Cables, Automotive Applications, Corrugated Pipe, Connectors, Monofilaments, Cable Jacketing, Film, Sporting Goods, Thermoforming Applications, Wires, Tubing, Electrical/Electronic Applications, Office Automation Equipment

Density: 1280.0 - 1280.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 1150.0 - 1150.0 MPa

Hytrel® 8238 is the highest modulus grade, with nominal hardness of 82D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Cubing, wire and cable, gears, sprockets, electrical connectors and oil field parts.

Kalrez® 6230 product card banner

DuPont

Kalrez® 6230

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Low Contamination From Extractables, Chemical Resistant, Good Steam Cycling Resistance

End Uses: Semiconductor Applications, O Rings

Color: Black

Kalrez® 6230/6230A* perfluoroelastomer parts are a black product that provide superior chemical resistance and low contamination from extractables in pharmaceutical and food handling applications where FDA compliance is required. Kalrez® 6230/6230A parts are especially suited for Water for Injection (WFI) systems, Steam-in-Place (SIP) cleaning and other critical systems. Kalrez° 6230/6230A parts are thermally stable up to 260°C (500°F), permitting them to be used in Stage II Sterilization processes, where other elastomers lose their sealing ability.

Kalrez® 6221 product card banner

DuPont

Kalrez® 6221

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Low Contamination From Extractables, Chemical Resistant, Good Steam Cycling Resistance

End Uses: Semiconductor Applications, O Rings

Color: White

Kalrez® 6221 perfluoroelastomer parts are a white product that provide superior chemical resistance and low contamination from extractables in pharmaceutical and food handling applications where FDA compliance is required. Kalrez® 6221 parts are especially suited for Water for Injection (WFI) systems, Steam-in-Place (SIP) cleaning and other critical systems. Kalrez® 6221 parts are thermally stable up to 260°C (500°F), permitting them to be used in Stage II Sterilization processes, where other elastomers lose their sealing ability. Kalrez® 6221 is available as O-rings. For white custom parts, please refer to Kalrez® LS205 parts.

Liveo™ Antifoam C Emulsion product card banner

DuPont

Liveo™ Antifoam C Emulsion

Chemical Name: Methylcellulose, Simethicone

Function: Defoamer

Labeling Claims: Halal, Kosher

Certifications & Compliance: Halal, Kosher, FDA 21 CFR Regulations, United States Pharmacopeia (USP)

Liveo™ Medical Antifoam C Emulsion is a highly effective and versatile silicone defoamer. Depending on foaming medium, this product eliminates foam that has already formed (defoams) and also prevents the formation of foam (antifoams). Liveo™ Medical Antifoam C Emulsion is a water-dilutable emulsion containing 30 percent by weight of Medical Antifoam A Compound (Simethicone USP) and methylcellulose. Liveo™ Medical Antifoam C Emulsion can be used as supplied or diluted with water. Its easy dilution makes this emulsion especially useful as a defoamer for aqueous systems, such as biofermentations.

Liveo™ 365 35% Dimethicone Nf Emulsion product card banner

DuPont

Liveo™ 365 35% Dimethicone NF Emulsion

Ready to Use Product Type: Lubricant

Application Areas: Medical Devices

Compatible Substrates & Surfaces: Polyolefins, Acrylic, Metal, Polyurethane, Polyamide, Polycarbonate (PC), Glass, Silicone, Elastomers & Rubbers, Polyvinyl Chloride (PVC), Fluoroelastomer, Plastics, Polystyrene (PS)

Features: Good Release Properties, Good Wettability, Low Wear, Excellent Lubricity, Low Friction

Chemical Family: Silicones

Liveo™ 365 35% Dimethicone NF Emulsion is a water-dilutable emulsion containing nonionic emulsifiers and 35% National Formulary Dimethicone. The emulsion is not manufactured or tested to be pyrogen free. Liveo™ 365 35% Dimethicone NF Emulsion may be used in a variety of applications where it is beneficial to dispense a lubricating silicone fluid in a water-dilutable delivery system.

Liveo™ Antifoam Q7-2587, 30% Simethicone Emulsion product card banner

DuPont

Liveo™ Antifoam Q7-2587, 30% Simethicone Emulsion

Chemical Name: Simethicone

Function: Defoamer

CAS Number: 8050-81-5

Labeling Claims: Halal, Kosher

Certifications & Compliance: Halal, European Pharmacopeia (Ph. Eur.), Kosher, FDA 21 CFR Regulations, United States Pharmacopeia (USP)

Liveo™ Q7-2587, 30% Simethicone Emulsion USP is a water-dilutable, non-ionic emulsion containing 30% Simethicone USP by weight. Emulsified Simethicone compound has less than 2% low-molecular-weight volatile silicone species. Tested according to and complies with all United States Phatmacopeia (USP) requirements for Simethicone emulsion, It has a smooth consistency that allows the product to be poured or pumped.

Liveo™ Mg 7-9900 Soft Skin Adhesive Kit (A & B) product card banner

DuPont

Liveo™ MG 7-9900 Soft Skin Adhesive Kit (A & B)

Ready to Use Product Type: Solvent free (100% Solids) Adhesive, 2K (2 component) Adhesive

Chemical Family: Silicones

Liveo™ MG 7-9900 Soft Skin Adhesive Kit (A & B) is a soft elastomeric silicone adhesive for adhering medical devices to the skin with medium adhesion force and gentle removal.

Delrin® 500t Bk602 product card banner

DuPont

Delrin® 500T BK602

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding, Extrusion

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 2100.0 - 2100.0 MPa

Delrin® 500T is a toughened, medium viscosity acetal homopolymer resin for injection molding with impact resistance similar to Delrin® 100. It can be used in parts requiring noise reduction.

Kalrez® Spectrum™ 6380 product card banner

DuPont

Kalrez® Spectrum™ 6380

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Chemical Resistant, Good Mechanical Properties

End Uses: Semiconductor Applications, O Rings

Color: Cream

Kalrez® Spectrum™ 6380 perfluoroelastomers parts are a non-black product developed specifically for chemical processes involving hot, aggressive amines. In addition, it has excellent overall chemical resistance (see chart below). This cream colored product is easily identifiable when selecting an O-ring material for harsh chemical plant services. This material has excellent mechanical properties and is a top choice for both static and dynamic sealing applications. A maximum service temperature of 225°C is suggested while short-term excursions to higher temperatures are permissible.

Liveo™ Q7-9180 Silicone Fluid 1 Cst product card banner

DuPont

Liveo™ Q7-9180 Silicone Fluid 1 cSt

Chemical Name: Octamethyltrisiloxane, Polydimethylsiloxane

Function: Emollient, Water Repellent, Skin Protectant

Labeling Claims: Halal, Kosher

Certifications & Compliance: Kosher, Halal

Liveo™ Q7-9180 Silicone Fluid 1 cSt is a Excipient for pharmaceutical applications. Liveo™ Q7-9180 Silicone Fluid is a clear colorless low viscosity linear siloxane liquid. Liveo™ Q7-9180 Fluid is commonly used as based fluid in topical formulation because of volatility, spreadability and smooth and non-greasy feel on the skin. Due to its high volatility and its anti-caking effect, the fluid can be considered as carrier for spray. Liveo™ Q7-9180 Fluid is currently used in a range of dermatological applications such as creams, gels, spray, wipes and formulation for the delivery of active. When used as an excipient in topical formulations, Liveo™ Q7-9180 Fluid can provide short term lubrication, smooth feel, emolliency, ease of spreading and reduced tackiness.

Liveo™ Biomedical Grade Hcr Q7-4735 product card banner

DuPont

Liveo™ BioMedical Grade HCR Q7-4735

Polymer Name: Silicone Elastomer

End Uses: Medical/Healthcare Applications, Medical Devices, Body Implants

Features: Enhanced Tear Resistant, Non Blooming, High Gas Permeability Pigmentable, Low Emissions, Good Colorability, High Consistency

Tear Strength: 35.0 - 35.0 kN/m

Silastic™ BioMedical Grade ETR Elastomers (QI-4720, Q7-4735, Q7-4750, QI-4765 and Q7-4780) are a series of two-part, Enhanced Tear-Resistant (ETR) silicone elastomers that consist of dimethyl and methylvinyl siloxane copolymers and reinforcing silica. The elastomers exhibit a range of hardness from soft (20 Shore A) to firm (80 Shore A). Each elastomer is supplied as a two-component kit (Part A and Part B), equal portions (by weight) of which must be thoroughly blended together prior to use. The elastomer is then thermally cured via addition-cure (platinum-cure) chemistry.

Hytrel® G4074 product card banner

DuPont

Hytrel® G4074

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Blow Molding, Casting, Injection Molding, Extrusion

End Uses: Electrical/Electronic Applications, Cast Films, Hoses, General Purpose, Cosmetic Packaging, Appliances, Cables, Automotive Applications, Cable Jacketing, Film, Sporting Goods, Thermoforming Applications, Wires, Tubing

Density: 1180.0 - 1180.0 kg/m³

Strain at Break: 250.0 - 250.0 %

Flexural Modulus: 65.0 - 65.0 MPa

Hytrel® G4074 is a low modulus grade with nominal hardness of 40D. It contains discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Hose and tubing, hose jackets, wire and cable jackets, film and sheeting, mouldedproducts. Not suited for light-colored finished products.

Kalrez® 0090 product card banner

DuPont

Kalrez® 0090

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings, Valve Seats

Features: High Modulus, Durable, Good Thermal Stability, High Hardness, Chemical Resistant

End Uses: Semiconductor Applications, Pump Parts, Valves, O Rings, Valve Parts

Color: Black

Kalrez® 0090 perfluoroelastomer parts deliver durable, reliable sealing solutions for applications requiring excellent rapid gas decompression (RGD) properties as well as high hardness, high modulus properties, and excellent extrusion resistance (even without backup rings). Potential oil and gas applications include downhole equipment such as drilling and completion tools, as well as industrial equipment including pumps, valves and compressors. Kalrez® 0090 has been certified by two independent laboratories to meet rigorous requirements for resistance to RGD. In addition to demonstrated RGD resistance, Kalrez® 0090 seals provide superior performance in regard to chemical and temperature properties. Chemical resistance: Kalrez® 0090 is resistant to chemicals encountered in the oil and gas industry, including sour process streams containing H2S. Broad temperature capability: Kalrez® 0090 retains good physical properties up to temperatures as high as 250°C (482°F) and down to 21°C (5.8°F). Under pressurized conditions, in laboratory tests, Kalrez® 0090 has demonstrated low temperature performance down to 40°C (40°F).

Liveo™ Pharma 50 Tubing product card banner

DuPont

Liveo™ Pharma 50 Tubing

Polymer Name: Silicone Elastomer

Physical Form: Tube

Features: Hydrophobic, Excellent Flexibility, Good Thermal Stability, Easily Sterilized, High Resilience, Consistent Performance, Low Emissions, Complete Traceability, Low Extractables, Rigorous Change Control

End Uses: Tubing, Medical/Healthcare Applications, Medical Devices

Tensile Strength: 90.0 - 90.0 MPa

Liveo™ Pharma 50 Tubing is Pharmaceutical grade silicone tubing for transferring of ultra-pure liquids, air or steam in pharmaceutical and biotechnological manufacturing processes. Designed for applications that require the transfer of high purity fluids where contamination is a concern like filling lines.

Liveo™ St-cyclomethicone 5 - Nf product card banner

DuPont

Liveo™ ST-Cyclomethicone 5 - NF

Chemical Name: Cyclopentasiloxane

Liveo™ ST-Cyclomethicone 5 - NF is a Excipient for pharmaceutical applications. Liveo™ ST-Cyclomethicone 5-NF is a clear, colorless, volatile polydimethylcyclosiloxane composed mainly of decamethylcyclopentasiloxane.

Delrin® 500t Nc010 product card banner

DuPont

Delrin® 500T NC010

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 2100.0 - 2100.0 MPa

Delrin® 500T is a toughened, medium viscosity acetal homopolymer resin for injection molding with impact resistance similar to Delrin® 100. It can be used in parts requiring noise reduction.

Liveo™ Class Vi Elastomers C6-180 Parts A & B product card banner

DuPont

Liveo™ Class VI Elastomers C6-180 Parts A & B

Polymer Name: Silicone Elastomer

Processing Methods: Extrusion

End Uses: Body Implants, Medical/Healthcare Applications, Medical Devices

Features: Cost Effective, Autoclaved, Platinum Catalyzed, High Gas Permeability, Non-tacky surface, Can be post cured, Pigmentable, Low Emissions, Lot-to-lot consistency, Non Blooming

Liveo™ Class VI Elastomers (C6-135. C6-150, C6-165. C6-180) Parts A & B are a series of two-part platinum-catalyzed silicone elastomers.

Kalrez® 8900 product card banner

DuPont

Kalrez® 8900

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: O-rings, Seals

Features: Fluorine Gas Resistant, Low Moisture Content, Excellent Resistance To Plasma Radicals, Low Compression Set, Good Thermal Stability, Low Outgassing

End Uses: Semiconductor Applications, O Rings

Color: Black

Kalrez® 8900 perfluoroelastomer parts are a black product for oxidation, diffusion, ALD, and LPCVD applications. It offers outstanding thermal stability, very low outgassing and excellent (low) compression set properties. Kalrez® 8900 parts exhibit excellent retention of physical properties at elevated temperatures, have excellent mechanical strength and are well-suited for both static and dynamic sealing applications. A maximum application temperature of 325°C (617°F) is suggested. Short excursions to higher temperatures may also be possible. Ultrapure post-cleaning and packaging is_x005F standard for all Kalrez® 8900 parts. _x005F

Delrin® 100st Bk602 product card banner

DuPont

Delrin® 100ST BK602

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding, Extrusion

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 1100.0 - 1100.0 MPa

Delrin® 100ST BK602 is a super-toughened, high viscosity acetal homopolymer grade with superior impact resistance. It is designed for highly stressed parts where outstanding toughness is essential.

Liveo™ Class Vi Elastomers C6-150 Parts A & B product card banner

DuPont

Liveo™ Class VI Elastomers C6-150 Parts A & B

Polymer Name: Silicone Elastomer

Processing Methods: Extrusion

End Uses: Body Implants, Medical/Healthcare Applications, Medical Devices

Features: Cost Effective, Autoclaved, Heat Stabilized, Platinum Catalyzed, High Gas Permeability, Non-tacky surface, Can be post cured, Pigmentable, Low Emissions, Lot-to-lot consistency, Non Blooming

Liveo™ Class VI Elastomers (C6-135, C6-150, C6-165, C6-180) Parts A & B are a series of two-part platinum-catalyzed silicone elastomers.

Liveo™ Antifoam Q7-2243 Lva, Simethicone Usp product card banner

DuPont

Liveo™ Antifoam Q7-2243 LVA, Simethicone USP

Chemical Name: Simethicone

Function: Defoamer

CAS Number: 8050-81-5

Labeling Claims: Halal, Kosher

Certifications & Compliance: Halal, European Pharmacopeia (Ph. Eur.), Kosher, FDA 21 CFR Regulations, United States Pharmacopeia (USP)

Liveo™ Q7-2243 LVA, Simethicone USP is a specially formulated low volatile silicone antifoarn designed for use in various medical and pharmaceutical applications requiring foam suppression or inhibition. Liveo™ Q7-2243 LVA, Simethicone USP is formulated and manufactured so that the quantity of volatile, low-molecular-weight silicone species is minimal. This low volatility (1 percent maximum) is especially advantageous in the manufacture of antiflatulent or antiflatulent/antacid tablets and other products where processing conditions, such as drying by high surface area exposure at elevated temperatures, will result in loss of volatile silicone species and subsequent low assay results for silicone fluid.

Liveo™ 366 35% Dimethicone Nf Emulsion product card banner

DuPont

Liveo™ 366 35% Dimethicone NF Emulsion

Ready to Use Product Type: Lubricant

Application Areas: Medical Devices

Compatible Substrates & Surfaces: Polyolefins, Acrylic, Metal, Polyurethane, Polyamide, Polycarbonate (PC), Glass, Silicone, Elastomers & Rubbers, Polyvinyl Chloride (PVC), Fluoroelastomer, Plastics, Polystyrene (PS)

Features: Good Release Properties, Good Wettability, Low Wear, Excellent Lubricity, Low Friction

Chemical Family: Silicones

Liveo™ 366 35% Dimethicone NF Emulsion is a water-dilutable emulsion containing nonionic emulsifiers and 35% National Formulary Dimethicone. The emulsion is not manufactured or tested to be pyrogen free. Liveo™ 366 35% Dimethicone NF Emulsion may be used in a variety of applications where it is beneficial to dispense a lubricating silicone fluid in a water-dilutable delivery system.

Delrin® 100st Nc010 product card banner

DuPont

Delrin® 100ST NC010

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding, Extrusion

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 1100.0 - 1100.0 MPa

Delrin® 100ST is a super-toughened, high viscosity acetal homopolymer grade with superior impact resistance. It is designed for highly stressed parts where outstanding toughness is essential.

Liveo™ 360 Medical Fluid 350 Cst product card banner

DuPont

Liveo™ 360 Medical Fluid 350 cSt

Ready to Use Product Type: Lubricant

Application Areas: Medical Devices

Compatible Substrates & Surfaces: Glass, Plastics, Elastomers & Rubbers, Metal

Features: Low Toxicity, Good Stability, Chemical Resistant, Excellent Lubricity, Excellent Water Resistance

Chemical Family: Silicones

Liveo™ 360 Medical Fluid is a clear, colorless polydimethylsiloxane liquid that is available in five standard viscosities.

Zytel® E51hsb Nc010 product card banner

DuPont

Zytel® E51HSB NC010

Polymer Name: Polyamide 66 (PA 66)

Processing Methods: Extrusion, Film Extrusion, Casting, Injection Molding, Coating

Additives Included: Mold Release Agent

Flexural Modulus: 2800.0 - 2800.0 MPa

Zytel® E51HSB NC010 is a high molecular weight, heat stabilized polyamide 66 resin for injection molding and extrusion.

Crastin® St820 Bk503 product card banner

DuPont

Crastin® ST820 BK503

Polymer Name: Polybutylene Terephthalate (PBT), Thermoplastic Polyester

Processing Methods: Injection Molding, Extrusion, Coating

Flexural Modulus: 1500.0 - 1500.0 MPa

Crastin® ST820 BK503 is an unreinforced, Super Tough polybutylene terephthalate resin for injection molding.

Crastin® Sc193 Nc010 product card banner

DuPont

Crastin® SC193 NC010

Polymer Name: PBT/SAN Alloy

Processing Methods: Injection Molding

Density: 1440.0 - 1440.0 kg/m³

Crastin® SC193 NC010 (Complete Data) is a 30% Glass Reinforced Polybutylene Terephthalate Blend Developed for Healthcare Industry

Hytrel® 4069 product card banner

DuPont

Hytrel® 4069

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Coating, Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion

End Uses: Cast Films, Hoses, Belts/Belt Repair, Cosmetic Packaging, Appliances, Cables, Automotive Applications, Corrugated Pipe, Film, Sporting Goods, Thermoforming Applications, Wires, Tubing, Office Automation Equipment

Density: 1110.0 - 1110.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 45.0 - 45.0 MPa

Hytrel® 4069 is a low modulus grade with nominal hardness of 40D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.

Hytrel® 4068fg product card banner

DuPont

Hytrel® 4068FG

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion

End Uses: Hoses, Cosmetic Packaging, Appliances, Non Specific Food Applications, Pipes, Cables, Corrugated Pipe, Film, Thermoforming Applications, Wires, Tubing

Density: 1110.0 - 1110.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 47.0 - 47.0 MPa

Hytrel® 4068FG is a high performance thermoplastic polyester elastomer developed for applications in contact with food.This product is manufactured according to Good Manufacturing Practice (GMP) principles and generally accepted in food contact applications in Europe and the USA when meeting applicable use conditions.

Liveo™ 7-9600 Soft Filling Elastomer Parts A & B product card banner

DuPont

Liveo™ 7-9600 Soft Filling Elastomer Parts A & B

Polymer Name: Silicone Elastomer

End Uses: Medical/Healthcare Applications, Medical Devices

Features: Pigmentable, Low Viscosity, Good Processability, Solventless, Good Colorability

Soft silicone elastomer for producing cohesive and soft feeling medical device parts.