Search:
Medical
239 products found on DuPont DuPont products found for View all Medicalon Knowde
Applications
Medical Devices & Assemblies
Other Medical Applications
Implants & Prosthetics
Tubing & Fluids Handling
Surgical Instruments & Trays
Wound Care
Laboratory & Diagnostics
Disposable Ware
With TDS
Hytrel® 6356 product card banner

DuPont

Hytrel® 6356

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion

End Uses: Fuel Tanks, Wire & Cable Applications, Gears, Hoses, Cosmetic Packaging, Appliances, Pipes, Automotive Applications, Corrugated Pipe, Monofilaments, Sporting Goods, Thermoforming Applications, Tubing, Electrical/Electronic Applications, Office Automation Equipment

Density: 1220.0 - 1220.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 290.0 - 290.0 MPa

Hytrel® 6356 is a medium modulus grade with nominal hardness of 63D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Hose and tubing, mandrels, wire and cable, film, profiles, seals, gears, sprockets, fuel tanks, containers with good permeation resistance to gases and liquids.

Hytrel® 7246 product card banner

DuPont

Hytrel® 7246

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Thermoforming, Extrusion, Sheet, Plaques & Profiles Extrusion, Film Extrusion, Casting, Injection Molding

End Uses: Hoses, SRS Pretensioner, Automotive Safety Retractor, Cable Jacketing, SRS Airbag, SRS Actuator, Sporting Goods, Electrical/Electronic Applications, Office Automation Equipment, Automotive Safety, Cast Films, Cosmetic Packaging, Appliances, Pipes, Automotive Applications, Corrugated Pipe, SRS Adjuster, SRS Seatbelt, Connectors, Monofilaments, Film, Safety Restrain System, EV Charger, Automotive Safety Pushbutton, Thermoforming Applications, Tubing, SRS Pillar Loop, Wire & Cable Applications, Safety Equipment, Signal Cord

Density: 1260.0 - 1260.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 550.0 - 550.0 MPa

Hytrel® 7246 is a high modulus grade with nominal hardness of 72D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.The 72 Shore D hardness is based on a legacy method and is still used for grade identification purposes.Typical applications:Tubing, wire and cable jackets, gears and sprockets, oil field parts.

Hytrel® 4556 product card banner

DuPont

Hytrel® 4556

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion, Coating

End Uses: Belts/Belt Repair, Hoses, Cosmetic Packaging, Appliances, Crates, Automotive Applications, Containers, Cable Jacketing, Hose Jackets, Film, Sporting Goods, Thermoforming Applications, Tubing, Electrical/Electronic Applications, Office Automation Equipment, Cast Films

Density: 1140.0 - 1140.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 87.0 - 87.0 MPa

Hytrel® 4556 is a medium modulus grade with nominal hardness of 45D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.

Hytrel® 5556 product card banner

DuPont

Hytrel® 5556

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Coating, Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion

End Uses: Cast Films, Wire & Cable Applications, Hoses, Cosmetic Packaging, Appliances, Pipes, Automotive Applications, Corrugated Pipe, Monofilaments, Cable Jacketing, Sporting Goods, Thermoforming Applications, Tubing, Electrical/Electronic Applications, Office Automation Equipment

Density: 1190.0 - 1190.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 190.0 - 190.0 MPa

Hytrel® 5556 is a medium modulus Hytrel® grade with nominal durometer hardness of 55D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Hose and tubing, wire and cable, film and sheeting, belting.

Delrin® Sc698 Nc010 product card banner

DuPont

Delrin® SC698 NC010

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding

Additives Included: Mold Release Agent

Flexural Modulus: 3000.0 - 3000.0 MPa

Common features of Delrin® acetal resins include mechanical and physical properties such as high mechanical strength and rigidity, excellent fatigue and impact resistance, as well as resistance to moisture, gasoline, lubricants, solvents, and many other neutral chemicals. Delrin® acetal resins also have excellent dimensional stability and good electrical insulating characteristics. They are naturally resilient, self-lubricating, and available in a variety of colors and speciality grades. Delrin® acetal resin typically is used in demanding applications in the automotive, domestic appliances, sports, industrial engineering, electronics, and consumer goods industries. Delrin® SC698 NC010 is a lubricated low viscosity acetal homopolymer, developed for high precision thin-walled parts requiring low wear and low friction with excellent surface aspect.

Hytrel® 3078 product card banner

DuPont

Hytrel® 3078

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Blow Molding, Casting, Injection Molding, Compounding, Calendering, Extrusion, Sheet, Plaques & Profiles Extrusion, Coating

End Uses: Cosmetic Packaging, Appliances, Automotive Applications, Film, Sporting Goods, Thermoforming Applications, Tubing, Electrical/Electronic Applications, Office Automation Equipment, Cast Films, Wire & Cable Applications

Density: 1070.0 - 1070.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 27.0 - 27.0 MPa

Hytrel® 3078 is a very low modulus grade, with nominal hardness of 30D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Food compliance:Refer to Hytrel® 3078FGTypical applications:Compounding, extrusion, injection molded and over-molded parts for consumer use.

Hytrel® 8238 product card banner

DuPont

Hytrel® 8238

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion

End Uses: Cast Films, Wire & Cable Applications, Gears, Hoses, Cosmetic Packaging, Appliances, Pipes, Automotive Applications, Corrugated Pipe, Connectors, Monofilaments, Cable Jacketing, Film, Sporting Goods, Thermoforming Applications, Tubing, Electrical/Electronic Applications, Office Automation Equipment

Density: 1280.0 - 1280.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 1150.0 - 1150.0 MPa

Hytrel® 8238 is the highest modulus grade, with nominal hardness of 82D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Cubing, wire and cable, gears, sprockets, electrical connectors and oil field parts.

Kalrez® 6230 product card banner

DuPont

Kalrez® 6230

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Low Contamination From Extractables, Chemical Resistant, Good Steam Cycling Resistance

End Uses: Semiconductor Applications, O Rings

Color: Black

Kalrez® 6230/6230A* perfluoroelastomer parts are a black product that provide superior chemical resistance and low contamination from extractables in pharmaceutical and food handling applications where FDA compliance is required. Kalrez® 6230/6230A parts are especially suited for Water for Injection (WFI) systems, Steam-in-Place (SIP) cleaning and other critical systems. Kalrez° 6230/6230A parts are thermally stable up to 260°C (500°F), permitting them to be used in Stage II Sterilization processes, where other elastomers lose their sealing ability.

Kalrez® 6221 product card banner

DuPont

Kalrez® 6221

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Low Contamination From Extractables, Chemical Resistant, Good Steam Cycling Resistance

End Uses: Semiconductor Applications, O Rings

Color: White

Kalrez® 6221 perfluoroelastomer parts are a white product that provide superior chemical resistance and low contamination from extractables in pharmaceutical and food handling applications where FDA compliance is required. Kalrez® 6221 parts are especially suited for Water for Injection (WFI) systems, Steam-in-Place (SIP) cleaning and other critical systems. Kalrez® 6221 parts are thermally stable up to 260°C (500°F), permitting them to be used in Stage II Sterilization processes, where other elastomers lose their sealing ability. Kalrez® 6221 is available as O-rings. For white custom parts, please refer to Kalrez® LS205 parts.

Kalrez® 3035 product card banner

DuPont

Kalrez® 3035

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: O-rings, Seals

Features: Chemical Resistant

End Uses: Semiconductor Applications, O Rings

Color: Black

Kalrez® 3035 perfluoroelastomer parts are a carbon black filled product well suited for use in production of valve stem packings. It may also be used to manufacture O-rings. Kalrez® 3035 was originally developed for use in Kalrez® KVSP® where low process temperatures or cold ambient conditions are involved. Chemical compatibility properties of Kalrez® 3035 are similar to those of Kalrez® 3018. This product has excellent chemical resistance to a wide variety of solvents and has a maximum service temperature of 288 °C (550 °F).

Liveo™ 365 35% Dimethicone Nf Emulsion product card banner

DuPont

Liveo™ 365 35% Dimethicone NF Emulsion

Ready to Use Product Type: Lubricant

Application Areas: Medical Devices

Compatible Substrates & Surfaces: Polyolefins, Acrylic, Metal, Polyurethane, Polyamide, Polycarbonate (PC), Glass, Silicone, Elastomers & Rubbers, Polyvinyl Chloride (PVC), Fluoroelastomer, Plastics, Polystyrene (PS)

Features: Good Release Properties, Good Wettability, Low Wear, Excellent Lubricity, Low Friction

Chemical Family: Silicones

Liveo™ 365 35% Dimethicone NF Emulsion is a water-dilutable emulsion containing nonionic emulsifiers and 35% National Formulary Dimethicone. The emulsion is not manufactured or tested to be pyrogen free. Liveo™ 365 35% Dimethicone NF Emulsion may be used in a variety of applications where it is beneficial to dispense a lubricating silicone fluid in a water-dilutable delivery system.

Kalrez® 1050lf product card banner

DuPont

Kalrez® 1050LF

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Amine Resistant, Good Compression Set

End Uses: Semiconductor Applications, O Rings, General Purpose

Color: Black

Kalrez® 1050LF perfluoroelastomer parts are a general-purpose product for O-rings, seals, and other parts used in chemical process industries. It has good hot water/steam resistance, excellent amine resistance, and good compression set properties. The maximum suggested service temperature is 288°C (550°F). It is not recommended for use in organic or inorganic acids at high temperatures.

Liveo™ Mg 7-9900 Soft Skin Adhesive Kit (A & B) product card banner

DuPont

Liveo™ MG 7-9900 Soft Skin Adhesive Kit (A & B)

Ready to Use Product Type: 2K (2 component) Adhesive & Sealant, Solvent free (100% Solids) Adhesive, Solvent free (100% Solids) Adhesive & Sealant, 2K (2 component) Adhesive

Chemical Family: Silicones

Liveo™ MG 7-9900 Soft Skin Adhesive Kit (A & B) is a soft elastomeric silicone adhesive for adhering medical devices to the skin with medium adhesion force and gentle removal.

Delrin® 500t Bk602 product card banner

DuPont

Delrin® 500T BK602

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding, Extrusion

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 2100.0 - 2100.0 MPa

Delrin® 500T is a toughened, medium viscosity acetal homopolymer resin for injection molding with impact resistance similar to Delrin® 100. It can be used in parts requiring noise reduction.

Kalrez® Spectrum™ 6380 product card banner

DuPont

Kalrez® Spectrum™ 6380

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings

Features: Chemical Resistant, Good Mechanical Properties

End Uses: Semiconductor Applications, O Rings

Color: Cream

Kalrez® Spectrum™ 6380 perfluoroelastomers parts are a non-black product developed specifically for chemical processes involving hot, aggressive amines. In addition, it has excellent overall chemical resistance (see chart below). This cream colored product is easily identifiable when selecting an O-ring material for harsh chemical plant services. This material has excellent mechanical properties and is a top choice for both static and dynamic sealing applications. A maximum service temperature of 225°C is suggested while short-term excursions to higher temperatures are permissible.

Liveo™ Biomedical Grade Hcr Q7-4735 product card banner

DuPont

Liveo™ BioMedical Grade HCR Q7-4735

Polymer Name: Silicone Elastomer

End Uses: Medical/Healthcare Applications, Medical Devices, Body Implants

Features: Enhanced Tear Resistant, Non Blooming, High Gas Permeability Pigmentable, Low Emissions, Good Colorability, High Consistency

Tear Strength: 35.0 - 35.0 kN/m

Silastic™ BioMedical Grade ETR Elastomers (QI-4720, Q7-4735, Q7-4750, QI-4765 and Q7-4780) are a series of two-part, Enhanced Tear-Resistant (ETR) silicone elastomers that consist of dimethyl and methylvinyl siloxane copolymers and reinforcing silica. The elastomers exhibit a range of hardness from soft (20 Shore A) to firm (80 Shore A). Each elastomer is supplied as a two-component kit (Part A and Part B), equal portions (by weight) of which must be thoroughly blended together prior to use. The elastomer is then thermally cured via addition-cure (platinum-cure) chemistry.

Hytrel® G4074 product card banner

DuPont

Hytrel® G4074

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Blow Molding, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion

End Uses: Electrical/Electronic Applications, Cast Films, Wire & Cable Applications, Hoses, General Purpose, Cosmetic Packaging, Appliances, Automotive Applications, Cable Jacketing, Film, Sporting Goods, Thermoforming Applications, Tubing

Density: 1180.0 - 1180.0 kg/m³

Strain at Break: 250.0 - 250.0 %

Flexural Modulus: 65.0 - 65.0 MPa

Hytrel® G4074 is a low modulus grade with nominal hardness of 40D. It contains discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.Typical applications:Hose and tubing, hose jackets, wire and cable jackets, film and sheeting, mouldedproducts. Not suited for light-colored finished products.

Kalrez® 0090 product card banner

DuPont

Kalrez® 0090

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: Seals, O-rings, Valve Seats

Features: High Modulus, Durable, Good Thermal Stability, High Hardness, Chemical Resistant

End Uses: Semiconductor Applications, Pump Parts, Valves, O Rings, Valve Parts

Color: Black

Kalrez® 0090 perfluoroelastomer parts deliver durable, reliable sealing solutions for applications requiring excellent rapid gas decompression (RGD) properties as well as high hardness, high modulus properties, and excellent extrusion resistance (even without backup rings). Potential oil and gas applications include downhole equipment such as drilling and completion tools, as well as industrial equipment including pumps, valves and compressors. Kalrez® 0090 has been certified by two independent laboratories to meet rigorous requirements for resistance to RGD. In addition to demonstrated RGD resistance, Kalrez® 0090 seals provide superior performance in regard to chemical and temperature properties. Chemical resistance: Kalrez® 0090 is resistant to chemicals encountered in the oil and gas industry, including sour process streams containing H2S. Broad temperature capability: Kalrez® 0090 retains good physical properties up to temperatures as high as 250°C (482°F) and down to 21°C (5.8°F). Under pressurized conditions, in laboratory tests, Kalrez® 0090 has demonstrated low temperature performance down to 40°C (40°F).

Liveo™ Pharma 50 Tubing product card banner

DuPont

Liveo™ Pharma 50 Tubing

Polymer Name: Silicone Elastomer

Physical Form: Tube

Features: Hydrophobic, Excellent Flexibility, Good Thermal Stability, Easily Sterilized, High Resilience, Consistent Performance, Low Emissions, Complete Traceability, Low Extractables, Rigorous Change Control

End Uses: Tubing, Medical/Healthcare Applications, Medical Devices

Tensile Strength: 90.0 - 90.0 MPa

Liveo™ Pharma 50 Tubing is Pharmaceutical grade silicone tubing for transferring of ultra-pure liquids, air or steam in pharmaceutical and biotechnological manufacturing processes. Designed for applications that require the transfer of high purity fluids where contamination is a concern like filling lines.

Delrin® 500t Nc010 product card banner

DuPont

Delrin® 500T NC010

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Injection Molding

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 2100.0 - 2100.0 MPa

Delrin® 500T is a toughened, medium viscosity acetal homopolymer resin for injection molding with impact resistance similar to Delrin® 100. It can be used in parts requiring noise reduction.

Delrin® 100st Bk602 product card banner

DuPont

Delrin® 100ST BK602

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Extrusion, Sheet, Plaques & Profiles Extrusion, Injection Molding

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 1100.0 - 1100.0 MPa

Delrin® 100ST BK602 is a super-toughened, high viscosity acetal homopolymer grade with superior impact resistance. It is designed for highly stressed parts where outstanding toughness is essential.

Liveo™ Class Vi Elastomers C6-180 Parts A & B product card banner

DuPont

Liveo™ Class VI Elastomers C6-180 Parts A & B

Polymer Name: Silicone Elastomer

Processing Methods: Extrusion

End Uses: Body Implants, Medical/Healthcare Applications, Medical Devices

Features: Cost Effective, Autoclaved, Platinum Catalyzed, High Gas Permeability, Non-tacky surface, Can be post cured, Pigmentable, Low Emissions, Lot-to-lot consistency, Non Blooming

Liveo™ Class VI Elastomers (C6-135. C6-150, C6-165. C6-180) Parts A & B are a series of two-part platinum-catalyzed silicone elastomers.

Kalrez® 8900 product card banner

DuPont

Kalrez® 8900

Polymer Name: Perfluoroelastomer (FFKM)

Physical Form: O-rings, Seals

Features: Fluorine Gas Resistant, Low Moisture Content, Excellent Resistance To Plasma Radicals, Low Compression Set, Good Thermal Stability, Low Outgassing

End Uses: Semiconductor Applications, O Rings

Color: Black

Kalrez® 8900 perfluoroelastomer parts are a black product for oxidation, diffusion, ALD, and LPCVD applications. It offers outstanding thermal stability, very low outgassing and excellent (low) compression set properties. Kalrez® 8900 parts exhibit excellent retention of physical properties at elevated temperatures, have excellent mechanical strength and are well-suited for both static and dynamic sealing applications. A maximum application temperature of 325°C (617°F) is suggested. Short excursions to higher temperatures may also be possible. Ultrapure post-cleaning and packaging is_x005F standard for all Kalrez® 8900 parts. _x005F

Liveo™ Class Vi Elastomers C6-150 Parts A & B product card banner

DuPont

Liveo™ Class VI Elastomers C6-150 Parts A & B

Polymer Name: Silicone Elastomer

Processing Methods: Extrusion

End Uses: Body Implants, Medical/Healthcare Applications, Medical Devices

Features: Cost Effective, Autoclaved, Heat Stabilized, Platinum Catalyzed, High Gas Permeability, Non-tacky surface, Can be post cured, Pigmentable, Low Emissions, Lot-to-lot consistency, Non Blooming

Liveo™ Class VI Elastomers (C6-135, C6-150, C6-165, C6-180) Parts A & B are a series of two-part platinum-catalyzed silicone elastomers.

Zytel® E51hsb Nc010 product card banner

DuPont

Zytel® E51HSB NC010

Polymer Name: Polyamide 66 (PA 66)

Processing Methods: Extrusion, Film Extrusion, Sheet, Plaques & Profiles Extrusion, Casting, Injection Molding, Coating

Additives Included: Mold Release Agent

Flexural Modulus: 2800.0 - 2800.0 MPa

Zytel® E51HSB NC010 is a high molecular weight, heat stabilized polyamide 66 resin for injection molding and extrusion.

Hytrel® 4068fg product card banner

DuPont

Hytrel® 4068FG

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion

End Uses: Hoses, Cosmetic Packaging, Appliances, Non Specific Food Applications, Pipes, Corrugated Pipe, Film, Thermoforming Applications, Tubing, Wire & Cable Applications

Density: 1110.0 - 1110.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 47.0 - 47.0 MPa

Hytrel® 4068FG is a high performance thermoplastic polyester elastomer developed for applications in contact with food.This product is manufactured according to Good Manufacturing Practice (GMP) principles and generally accepted in food contact applications in Europe and the USA when meeting applicable use conditions.

Hytrel® 4069 product card banner

DuPont

Hytrel® 4069

Polymer Name: Thermoplastic Copolyester Elastomer (TPC-ET)

Processing Methods: Film Extrusion, Thermoforming, Casting, Injection Molding, Extrusion, Sheet, Plaques & Profiles Extrusion, Coating

End Uses: Hoses, Belts/Belt Repair, Cosmetic Packaging, Appliances, Automotive Applications, Corrugated Pipe, Film, Sporting Goods, Thermoforming Applications, Tubing, Office Automation Equipment, Cast Films, Wire & Cable Applications

Density: 1110.0 - 1110.0 kg/m³

Strain at Break: 300.0 - 300.0 %

Flexural Modulus: 45.0 - 45.0 MPa

Hytrel® 4069 is a low modulus grade with nominal hardness of 40D. It contains non-discoloring stabilizer. It can be processed by many conventional thermoplastic processing techniques like injection molding and extrusion.

Crastin® Sc193 Nc010 product card banner

DuPont

Crastin® SC193 NC010

Polymer Name: PBT/SAN Alloy

Processing Methods: Injection Molding

Density: 1440.0 - 1440.0 kg/m³

Crastin® SC193 NC010 (Complete Data) is a 30% Glass Reinforced Polybutylene Terephthalate Blend Developed for Healthcare Industry

Crastin® St820 Bk503 product card banner

DuPont

Crastin® ST820 BK503

Polymer Name: Polybutylene Terephthalate (PBT), Thermoplastic Polyester

Processing Methods: Injection Molding, Extrusion, Coating, Sheet, Plaques & Profiles Extrusion

Flexural Modulus: 1500.0 - 1500.0 MPa

Crastin® ST820 BK503 is an unreinforced, Super Tough polybutylene terephthalate resin for injection molding.

Liveo™ 360 Medical Fluid 350 Cst product card banner

DuPont

Liveo™ 360 Medical Fluid 350 cSt

Ready to Use Product Type: Lubricant

Application Areas: Medical Devices

Compatible Substrates & Surfaces: Glass, Plastics, Elastomers & Rubbers, Metal

Features: Low Toxicity, Good Stability, Chemical Resistant, Excellent Lubricity, Excellent Water Resistance

Chemical Family: Silicones

Liveo™ 360 Medical Fluid is a clear, colorless polydimethylsiloxane liquid that is available in five standard viscosities.

Liveo™ 366 35% Dimethicone Nf Emulsion product card banner

DuPont

Liveo™ 366 35% Dimethicone NF Emulsion

Ready to Use Product Type: Lubricant

Application Areas: Medical Devices

Compatible Substrates & Surfaces: Polyolefins, Acrylic, Metal, Polyurethane, Polyamide, Polycarbonate (PC), Glass, Silicone, Elastomers & Rubbers, Polyvinyl Chloride (PVC), Fluoroelastomer, Plastics, Polystyrene (PS)

Features: Good Release Properties, Good Wettability, Low Wear, Excellent Lubricity, Low Friction

Chemical Family: Silicones

Liveo™ 366 35% Dimethicone NF Emulsion is a water-dilutable emulsion containing nonionic emulsifiers and 35% National Formulary Dimethicone. The emulsion is not manufactured or tested to be pyrogen free. Liveo™ 366 35% Dimethicone NF Emulsion may be used in a variety of applications where it is beneficial to dispense a lubricating silicone fluid in a water-dilutable delivery system.

Delrin® 100st Nc010 product card banner

DuPont

Delrin® 100ST NC010

Polymer Name: Polyacetal Homopolymer (POM)

Processing Methods: Extrusion, Sheet, Plaques & Profiles Extrusion, Injection Molding

Additives Included: Mold Release Agent, Lubricant (Unspecified)

Flexural Modulus: 1100.0 - 1100.0 MPa

Delrin® 100ST is a super-toughened, high viscosity acetal homopolymer grade with superior impact resistance. It is designed for highly stressed parts where outstanding toughness is essential.

Liveo™ Class Vi Elastomers C6-165 Parts A & B product card banner

DuPont

Liveo™ Class VI Elastomers C6-165 Parts A & B

Polymer Name: Silicone Elastomer

Processing Methods: Extrusion

End Uses: Body Implants, Medical/Healthcare Applications, Medical Devices

Features: Cost Effective, Heat Stabilized, Autoclaved, Platinum Catalyzed, High Gas Permeability, Non-tacky surface, Can be post cured, Pigmentable, Lot-to-lot consistency, Non Blooming

Liveo™ Class VI Elastomers (C6-135, C6-150, C6-165, C6-180) Parts A & B are a series of two-part platinum-catalyzed silicone elastomers.

Liveo™ Biomedical Grade Hcr Q7-4750 product card banner

DuPont

Liveo™ BioMedical Grade HCR Q7-4750

Polymer Name: Silicone Elastomer

End Uses: Medical/Healthcare Applications, Medical Devices, Body Implants

Features: High Gas Permeability Pigmentable, Low Emissions, Good Colorability, High Consistency, Enhanced Tear Resistant, Non Blooming

Tear Strength: 46.0 - 46.0 kN/m

Silastic™ BioMedical Grade ETR Elastomers (QI-4720, Q7-4735, Q7-4750, QI-4765 and Q7-4780) are a series of two-part, Enhanced Tear-Resistant (ETR) silicone elastomers that consist of dimethyl and methylvinyl siloxane copolymers and reinforcing silica. The elastomers exhibit a range of hardness from soft (20 Shore A) to firm (80 Shore A). Each elastomer is supplied as a two-component kit (Part A and Part B), equal portions (by weight) of which must be thoroughly blended together prior to use. The elastomer is then thermally cured via addition-cure (platinum-cure) chemistry.

Liveo™ Mg 7-9800 Soft Skin Adhesive Kit (A & B) product card banner

DuPont

Liveo™ MG 7-9800 Soft Skin Adhesive Kit (A & B)

Ready to Use Product Type: 2K (2 component) Adhesive & Sealant, Solvent free (100% Solids) Adhesive, Solvent free (100% Solids) Adhesive & Sealant, 2K (2 component) Adhesive

Chemical Family: Silicones

Liveo™ MG 7-9800 Soft Skin Adhesive Kit (A & B) is a soft elastomeric silicone adhesive for adhering medical devices to the skin with light adhesion force and gentle removal.

Liveo™ Qp1-250 Liquid Silicone Rubber Kit product card banner

DuPont

Liveo™ QP1-250 Liquid Silicone Rubber Kit

Polymer Name: Silicone Elastomer, Liquid Silicone Rubber (LSR)

Processing Methods: Injection Molding, Liquid Injection Molding

End Uses: Body Implants, Medical/Healthcare Applications, Medical Devices

Features: Fast Production Cycle, Heat Stabilized, Autoclaved, Consistent High Quality, Good Colorability, High Gas Permeability, Platinum Catalyzed, Good Processability, Low Emissions, Non Blooming

Liveo™ QP1 Liquid Silicone Rubbers (LSRs) are platinum-catalyzed, heat-cured materials designed for the fabrication of medical devices and device components including those intended for implantation in humans for less than 30 days and non-implant applications, specifically designed for liquid injection molding.