Low dielectric properties for radar transparency
Material and design solutions for radar absorbency
Excellent dimensional stability and low warpage
Excellent balance of mechanical properties
Resistance to exterior environments, including road salt, automotive fluids, thermal cycling, and hydrolysis resistance
Improved laser-marking properties

Back Housing and Connector

Higher thermal conductivity for heat dissipation
EMI shielding (depending on requirements)
Improved toughness
Superior hydrolysis resistance for hot and humid environments
Improved thermal-shock-cycling resistance
Available laser transparent and improved laser marking
Low warpage for higher dimensional control
Standard grade with good mechanical properties

Mounting Brackets Sensor Support

Excellent combination of toughness and stiffness
Good chemical resistance
Extensive material data available for anisotropic analysis
Improved laser marking solutions available

Radome

Improved radio transparency with low Dk and low Df
Excellent dimensional stability
Improved toughness
Superior hydrolysis resistance for hot and humid environments
Available laser transparent and with improved laser marking.
Low warpage for higher dimensional control
Standard grade with good mechanical properties

Applications & Uses

Markets

Automotive & Transportation,

Electrical & Electronics

Applications

Automotive & Transportation — Automotive ,

Other Automotive Applications,

Electrical & Electronics — Devices & Assemblies,

Other Devices & Assemblies,

Electrical & Electronics — Parts & Components,

Connectors,

Sensors & Actuators,

Plastics & Elastomers End Uses

Automotive Applications,

Electrical Connectors,

Electrical/Electronic Applications,

Mounting Brackets

Plastics & Elastomers Processing Methods

Injection Molding

Properties

Physical Properties


	Value	Units	Test Method / Conditions
Viscosity Number	143/-	cm³/g	ISO 307, 1157, 1628
Molding Shrinkage - Parallel	0.3/-	%	ISO 294-4, 2577
Molding Shrinkage - Normal	1.1/-	%	ISO 294-4, 2577

Mechanical Properties


	Value	Units	Test Method / Conditions
Tensile Modulus	11000/8000	MPa	ISO 527-1/-2
Hardness, Rockwell	101	Scale M	ISO 2039-2
Stress at Break	200/140	MPa	ISO 527-1/-2
Strain at Break	3/5	%	ISO 527-1/-2
Flexural Modulus	9500/6000	MPa	ISO 178
Flexural Strength	280/195	MPa	ISO 178
Charpy Impact Strength (23°C)	75/80	kJ/m²	ISO 179/1eU
Charpy Notched Impact Strength (23°C)	13/17	kJ/m2	ISO 179/1eA
Charpy Notched Impact Strength (-40°C)	10/10	kJ/m²	ISO 179/1eA
Izod Notched Impact Strength (23°C)	12/15	kJ/m²	ISO 180/1A
Izod Notched Impact Strength (-40°C)	10/10	kJ/m²	ISO 180/1A
Izod Impact Strength (23°C)	80/-	kJ/m²	ISO 180/1U
Izod Impact Strength (-30°C)	80/-	kJ/m²	ISO 180/1U
Ball Indentation Hardness (H 961/30)	280/-	MPa	ISO 2039-1
Poisson's Ratio	0.34/0.34	-	-

Thermal Properties


	Value	Units	Test Method / Conditions
Melting Temperature (10°C/min)	262/-	°C	ISO 11357-1/-3
Temperature of Deflection Under Load(1.8 MPa)	252/-	°C	ISO 75-1/-2
Temperature of Deflection Under Load (0.45 MPa)	261/-	°C	ISO 75-1/-2
Coefficient of Linear Thermal Expansion - Parallel	18/-	E-6/K	ISO 11359-1/-2
Coefficient of Linear Thermal Expansion - Normal	83/-	E-6/K	ISO 11359-1/-2
Coefficient of Linear Thermal Expansion - Normal (-40 - 23°C)	65/-	E-6/K	ISO 11359-1/-2
Coefficient of Linear Thermal Expansion - Normal (55 - 160°C)	140/-	E-6/K	ISO 11359-1/-2
Coefficient of Linear Thermal Expansion - Parallel (-40 - 23°C)	24/-	E-6/K	ISO 11359-1/-2
Coefficient of Linear Thermal Expansion - Parallel (55 - 160°C)	13/-	E-6/K	ISO 11359-1/-2
Relative Temperature Index - Electrical (0.75 mm)	140	°C	UL 746B
Relative Temperature Index - Electrical (1.5 mm)	140	°C	UL 746B
Relative Temperature Index - Electrical (3 mm)	140	°C	UL 746B
Relative Temperature Index - Impact (0.75 mm)	125	°C	UL 746B
Relative Temperature Index - Impact (1.5 mm)	125	°C	UL 746B
Relative Temperature Index - Impact (3 mm)	125	°C	UL 746B
Relative Temperature Index - Strength (0.75 mm)	140	°C	UL 746B
Relative Temperature Index - Strength (1.5 mm)	140/-	°C	UL 746B
Relative Temperature Index - Strength (3 mm)	140	°C	UL 746B

Electrical Properties


	Value	Units	Test Method / Conditions
Comparative Tracking Index - CTI	400/-	V	IEC 60112
Electric Strength - Short Time (2 mm)	18/-	kV/mm	IEC 60243-1

Flammability


	Value	Units	Test Method / Conditions
Burning Behaviour (1.5 mm, Nominal Thickness)	HB/-	class	IEC 60695-11-10
Burning Behaviour (Thickness h)	HB/-	class	IEC 60695-11-10
Glow Wire Flammability Index - GWFI (0.75 mm)	725/-	°C	IEC 60695-2-12
Glow Wire Flammability Index - GWFI (1.5 mm)	700/-	°C	IEC 60695-2-12
Glow Wire Flammability Index - GWFI (3 mm)	800/-	°C	IEC 60695-2-12
Glow Wire Ignition Temperature - GWIT (0.75 mm)	750/-	°C	IEC 60695-2-13
Glow Wire Ignition Temperature - GWIT (1.5 mm)	725/-	°C	IEC 60695-2-13
Glow Wire Ignition Temperature (3 mm)	825/-	°C	IEC 60695-2-13
FMVSS Class	B	-	ISO 3795 (FMVSS 302)
Burning Rate (1 mm, Thickness)	28	mm/min	ISO 3795 (FMVSS 302)
Ul Recognition	Yes/-	-	UL 94
Thickness Tested	1.5/-	mm	IEC 60695-11-10

Other Properties


	Value	Units	Test Method / Conditions
Humidity Absorption (2 mm)	1.8/-	%	Sim. to ISO 62
Water Absorption (2 mm)	5.7/-	%	Sim. to ISO 62
Water Absorption - Immersion (24 h)	1.2/-	%	Sim. to ISO 62
Density	1390/-	kg/m³	ISO 1183

Processing Information (Injection Molding)


	Value	Units	Test Method / Conditions
Drying Recommended	Yes	-	-
Drying Temperature	80	°C	-
Drying Time (Dehumidified Dryer)	2.0 - 4.0	h	-
Processing Moisture Content	≤0.2	%	-
Melt Temperature Optimum	285	°C	-
Min. Melt Temperature	275	°C	-
Max. Melt Temperature	2951	°C	-
Max. Screw Tangential Speed	0.2/-	m/s	-
Mold Temperature Optimum	100	°C	-
Min. Mold Temperature	70	°C	-
Max. Mold Temperature	120	°C	-
Hold Pressure Range	50 - 100	MPa	-
Hold Pressure Time	3	s/mm	-
Ejection Temperature	210	°C	-

VDA Properties


	Value	Units	Test Method / Conditions
Emission of Organic Compounds	10	µgC/g	VDA 277
Odour	3	class	VDA 270
Fogging, G - Value (Condensate)	0.6/-	mg	ISO 6452

Solutions for Mounting Brackets Sensor Support

	Stiffness Strength	Vibration Fatigue & Creep	Dimensional Stability	Heat Resistance	Hydrolysis Resistance	Road Salt Resistance	Laser Markable	Snap Fit	EMI Shielding (77GHz)
Zytel® 70G33HS1L	+++	+++	++	++++	++++	++++	++	++	++

Best: ++++

Chemical Resistance

Chemical Type	Chemical Name	Resistance
Acids	Acetic Acid (5% by mass) (23°C)	Probably Resistant
Acids	Chromic Acid solution (40% by mass) (23°C)	Not Recommended
Acids	Citric Acid solution (10% by mass) (23°C)	Probably Resistant
Acids	Hydrochloric Acid (36% by mass) (23°C)	Not Recommended
Acids	Lactic Acid (10% by mass) (23°C)	Probably Resistant
Acids	Nitric Acid (40% by mass) (23°C)	Not Recommended
Acids	Sulfuric Acid (38% by mass) (23°C)	Not Recommended
Acids	Sulfuric Acid (5% by mass) (23°C)	Not Recommended
Alcohols	Ethanol (23°C)	Probably Resistant
Alcohols	Isopropyl alcohol (23°C)	Probably Resistant
Alcohols	Methanol (23°C)	Probably Resistant
Bases	Ammonium Hydroxide solution (10% by mass) (23°C)	Probably Resistant
Bases	Sodium Hydroxide solution (1% by mass) (23°C)	Probably Resistant
Bases	Sodium Hydroxide solution (35% by mass) (23°C)	Not Recommended
Ethers	Diethyl ether (23°C)	Probably Resistant
Hydrocarbons	iso-Octane (23°C)	Probably Resistant
Hydrocarbons	n-Hexane (23°C)	Probably Resistant
Hydrocarbons	Toluene (23°C)	Probably Resistant
Ketones	Acetone (23°C)	Probably Resistant
Mineral oils	Automatic hypoid-gear oil Shell Donax TX (135°C)	Probably Resistant
Mineral oils	Hydraulic oil Pentosin CHF 202 (125°C)	Probably Resistant
Mineral oils	Insulating Oil (23°C)	Probably Resistant
Mineral oils	Motor oil OS206 304 Ref.Eng.Oil, ISP (135°C)	Probably Resistant
Mineral oils	SAE 10W40 multigrade motor oil (130°C)	Probably Resistant
Mineral oils	SAE 10W40 multigrade motor oil (23°C)	Probably Resistant
Mineral oils	SAE 80/90 hypoid-gear oil (130°C)	Probably Resistant
Other	1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)	Probably Resistant
Other	50% Oleic acid + 50% Olive Oil (23°C)	Probably Resistant
Other	DOT No. 4 Brake fluid (130°C)	Probably Resistant
Other	Ethyl Acetate (23°C)	Probably Resistant
Other	Ethylene Glycol (50% by mass) in water (108°C)	Probably Resistant
Other	Hydrogen peroxide (23°C)	Not Recommended
Other	Phenol solution (5% by mass) (23°C)	Not Recommended
Other	Water (23°C)	Probably Resistant
Other	Water (90°C)	Probably Resistant
Salt solutions	Sodium Carbonate solution (2% by mass) (23°C)	Probably Resistant
Salt solutions	Sodium Carbonate solution (20% by mass) (23°C)	Probably Resistant
Salt solutions	Sodium Chloride solution (10% by mass) (23°C)	Probably Resistant
Salt solutions	Sodium Hypochlorite solution (10% by mass) (23°C)	Not Recommended
Salt solutions	Zinc Chloride solution (50% by mass) (23°C)	Not Recommended
Standard Fuels	Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)	Probably Resistant
Standard Fuels	Diesel fuel (pref. ISO 1817 Liquid F) (23°C)	Probably Resistant
Standard Fuels	Diesel fuel (pref. ISO 1817 Liquid F) (90°C)	Probably Resistant
Standard Fuels	ISO 1817 Liquid 1 - E5 (60°C)	Probably Resistant
Standard Fuels	ISO 1817 Liquid 2 - M15E4 (60°C)	Probably Resistant
Standard Fuels	ISO 1817 Liquid 3 - M3E7 (60°C)	Probably Resistant
Standard Fuels	ISO 1817 Liquid 4 - M15 (60°C)	Probably Resistant
Standard Fuels	Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)	Probably Resistant
Standard Fuels	Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)	Probably Resistant