Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Applications
- Application Area
- Applications
- Field Assembly : Mix and cure in the field
- Optics : Active alignment of optics such as lenses,prisms, diodes, filters, etc. to opto-circuit
- Fiber Optics : “field curing” or field assembly ofconnectors and couplers, also suggested for fiber opticsplicing
- Medical : Adhesion to most metals, plastics, ceramics,and glasses found in tubing, substrates or housing
- General : Arts and crafts repair, restoration, andhobbyists
- Instructions for Use
- Mix Resin: Hardener – 100:46 grams by weight or 2:1by volume and vacuum degas.
- Cure as recommended achieving the desiredproperties.
- Typical cured properties were determined usingrecommended cure schedule.
- Some difference in properties may occur with thealternate or other cure schedules.
Properties
- Typical Cured Properties
- Handling Properties
| Value | Units | Test Method / Conditions | |
| Specific Gravity | 1.1 | — | — |
| Hardness | 86 | Shore D | — |
| Lap Shear Strength to Aluminium (at -55°C) | 2300 | psi | — |
| Lap Shear Strength to Aluminium (at 25°C) | 3100 | psi | — |
| Lap Shear Strength to Aluminium (at 95°C) | 150 | psi | — |
| Die Shear Strength | 1800 | psi | — |
| Refractive Index | 1.54 | — | — |
| Service Temperature Range | -55 to 125 | °C | — |
| Glass Transition Temperature (Tg) | min. 70 | °C | — |
| Coefficient of Linear Thermal Expansion (Below Tg) | 62 | 10⁻⁶/°C | — |
| Coefficient of Linear Thermal Expansion (Above Tg) | min. 200 | 10⁻⁶/°C | — |
| Dielectric Strength | 600 | Volts/mil | — |
| Dielectric Constant (at 1 kHz) | 3.2 | — | — |
| Dissipation Factor (at 1 kHz) | 0.02 | — | — |
| Volume Resistivity | 1x10¹³ | ohm-cm | — |
| Value | Units | Test Method / Conditions | |
| Adhesive | Part A | — | — |
| Hardener | Part B | — | — |
| Mix Ratio by Weight (Resin/Hardener) | 100/46 | — | — |
| Mix Ratio by Volume (Resin/Hardener) | 100/50 | — | — |
| Mixed Viscosity (at 25°C) | 4,000 - 7,000 | cps | — |
| Pot Life (at 25°C, 100 grams) | min. 4 | hours | — |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Curing Information
- Recommended Cure : 3 hours at 65°C
- Alternate Cure : 24 hours at 25°C
Safety & Health
- Safety Information
- For Industrial Use Only : Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning : Although the system contains low volatility materials, care should be taken in handling. Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet for additional health and safety information.
Packaging & Availability
- Packaging Type
- Availability
- Packaged in Pint, Quart, Gallon, and 5-Gallon kit size.
- Also available in 50cc dual syringe cartridge
Storage & Handling
- Shelf Life
- 1 Year
- Storage & Shelf Life
One year when stored in unopened containers at an average temperature of 25°C.