Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Features
- Toughened
- Crack resistant
- Component epoxy adhesive with fast cure at high temperatures
- Excellent adhesion to metals, ceramics, glass and plastics
Applications & Uses
- Markets
- Applications
- Cure Method
- Instructions for Use
- Dispense or apply needed amount on to the device or substrate.
- Cure as recommended achieving the desired properties.
- Typical cured properties were determined using recommended cure schedule. Some difference in properties may occur with the alternate or other cure schedules.
Properties
- Typical Cured Properties
- Handling Properties
- Note
Typical Cured Properties After Recommended Cure : Tested at 25°C unless otherwise indicated
| Value | Units | Test Method / Conditions | |
| Specific Gravity | 1.44 | — | — |
| Hardness | 85 | Shore D | — |
| Elongation | max. 2 | % | — |
| Water Absorption (7days Submersion at 25°C) | 0.28 | % | — |
| Lap Shear Strength to Aluminium | 4500 | psi | — |
| Lap Shear Strength to Stainless Steel | 2500 | psi | — |
| Lap Shear Strength to Grit Blasted Steel | 4300 | psi | — |
| Lap Shear Strength to Polycarbonate | 2000 | psi | — |
| T-peel Strength to Steel (5-8mil bondline) | 50 | lb/in of width | — |
| Service Temperature Range | -55 to 200 | °C | — |
| Glass Transition Temperature (Tg) | min. 100 | °C | — |
| Coefficient of Linear Thermal Expansion (Below Tg) | 40 | 10⁻⁶/°C | — |
| Coefficient of Linear Thermal Expansion (Above Tg) | 160 | 10⁻⁶/°C | — |
| NASA Outgassing Data (TML) | 0.29 | % | — |
| NASA Outgassing Data (WVR) | 0.23 | % | — |
| NASA Outgassing Data (CVCM) | 0.01 | % | — |
| Dielectric Strength | 80 | Volts/mil | — |
| Dielectric Constant (at 1 kHz) | 4.28 | — | — |
| Dissipation Factor (at 1 kHz) | 0.4 | — | — |
| Volume Resistivity | 2.5 x 10¹⁴ | ohm-cm | — |
| Value | Units | Test Method / Conditions | |
| Viscosity (at 25°C) | Paste | — | — |
| Pot Life (at 100°C, 20 grams) | 10 - 15 | minutes | — |
Regulatory & Compliance
- Certifications & Compliance
Technical Details & Test Data
- Curing Information
Typical Curing Time : 30 min at 120°C or 20 min at 150°C
Safety & Health
- Safety Information
- For Industrial Use Only : Practices of good housekeeping, safety and cleanliness should be followed before, during and after use.
- Warning : Although the system contains low volatility materials, care should be taken in handling. Adequate ventilation of work place and ovens is essential. These materials may cause injury to the skin following prolonged or repeated contact and dermatitis in susceptible individuals. In case of skin contact, wash thoroughly with soap and water. For eyes, flush immediately with plenty of water for at least 10 minutes and seek medical attention. Refer to Material Safety Data Sheet for additional health and safety information.
Packaging & Availability
- Packaging Type
- Packaging Options
- Available in quart and gallon containers.
- Also available in 30mL syringe or 10oz cartridge.
Storage & Handling
- Shelf Life
- 3 Months (at 25°C), 6 Months (at 0°C)
- Storage & Shelf Life
The shelf life of these materials is 3 months when stored in unopened containers at an average temperature of 25°C or 6 months when stored at 0°C or below.