Knowde Enhanced TDS
Identification & Functionality
- Product Type
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- 847 Carbon Conductive Assembly Paste
A smooth stiff paste designed to fill gaps and improve connections between non-moving parts without bleeding, separating, or migrating.
- Bleed resistant
- Resists separation
- Silicone Free
- Key Attributes
- Ensures continuous electrical contact between pitted, scratched, loose, or vibrating connectors
- Prevents arcing, pitting, hotspots, and
- Prevents corrosion
- Lubricates
- Repels water and humidity
- Safe on plastics
- Thin bond line capabilities
- Resistivity of 23 Ω·cm
- Improves electrical connections between irregular, pitted or corroded surfaces
- Ensures electrical contact between loose or vibrating parts
- Prevents arching, pitting, hotspots and welds
- Inhibits corrosion
- Fills gaps
- Can be used on vertical surfaces
- Silicone-free
Applications & Uses
- Applications
- Application Instructions
To apply the grease:
- Wear protective gloves.
- Clean and dry the surface being lubricated with a lint-free cloth or brush and a zero-residue cleaning solvent, such as MG 824 Isopropyl Alcohol.
- Apply a thin, even layer of grease using a spatula or other appropriate applicator.
Attention!
Carbon grease is messy and transfers easily. Be careful not to spread it beyond the intended area.- Application
- Audio jacks
- Automotive connectors
- Battery terminals
- Bus bars
- Light sockets
- Headlights
- HVAC connections
- Ground connections
- Rotating connections
- Power cords and jacks
- Slip Rings
- Plugs and sockets
- Slide connectors
- Sound systems
Properties
- Physical Properties
- Typical Properties
- Electrical Properties
- Grease Properties
- Synthetic Oil Properties
- Temperature Properties
- Temperature Properties Note
- a) Cold storage avoids material separation and settling. If storing at room temperature, mix thoroughly to disperse filler before use.
- Carbon Conductive Greases Comparison Chart
8481
846
847
PROPERTIES
Conductive filler
Carbon, graphite
Carbon
Carbon
Base material
Synthetic oil
Silicone oil
Synthetic oil
Constant service temperature
-68 to 165 °C [-90 to 329 °F]
-50 to 200 °C [-58 to 392 °F]
-68 to 165 °C [-90 to 329 °F]
Electrical Properties
Volume resistivity (rv)
160 W·cm
114 W·cm
23 W·cm
Volume conductivity (sv)
0.006 S/cm
0.009 S/cm
0.04 S/cm
Thermal Properties
Thermal conductivity at 25 °C [77 °F]
0.29 W/(m·K)
N/E
N/E
Grease Properties
Evaporation loss, 22 h at 165 °C [329 °F]
2.0
2.6
0.3
Oil separation, 30 h at 165 °C [329 °F]
5.0
0.4
1.8
Dropping point
>300°C [>572 °F]
>304 °C [>579 °F]
>304 °C [>579 °F]
Water washout at 38 °C [100 °F]
0.9
1.3
0.2
Emcor rust test, distilled water
0, no corrosion
1
3
Worked penetration, 60 strokes, ½ scale
315
269
174
Physical Properties
Color
Black
Black
Black
Odor
Odorless
Odorless
Odorless
Density at 25 °C [77 °F]
1.01 g/mL
1.05 g/mL
1.07 g/mL
Viscosity
128 Pa·s
386 Pa·s
N/E
Lubricant
Yes
Yes
Yes
Bleed resistant
Yes
No
Yes
Corrosion resistant
Yes
Yes
Yes
VOC (Volatile Organic Compound)
4%
0
0
Synthetic Oil Properties
Oil viscosity index
>110 °C [>230 °F]
N/A
>110 °C [>230 °F]
Fire point
321 °C [610 °F]
N/A
321 °C [610 °F]
Flash point
>290 °C [>554 °F]
N/A
>290 °C [>554 °F]
- Physical and Synthetic Oil Properties Note
- Values based on synthetic oil component only.
- a) High oil viscosity index of more than 100 indicates a small oil viscosity change with temperature.
- b) Temperature at which oil will continue to burn for at least 5 s after ignition with an open flame.
- c) Cleveland open cup method.
- Emcor Rust Test, Distilled Water Note
- a) Corroded areas covering >1% but <5% of the running track surface.
Value | Units | Test Method / Conditions | |
Bleed Resistant | Yes | — | — |
Corrosion Resistant | Yes | — | — |
Lubricant | Yes | — | — |
Volatile Organic Compound (VOC) | 0 | % | — |
Run Resistant | Yes | — | — |
Odor | Odorless | — | — |
Viscosity | Thixotropic paste | — | — |
Density (at 25 °C, 77 °F) | 1.07 | g/mL | ASTM D 1475 |
Value | Units | Test Method / Conditions | |
Maximum Intermittent Temperature | 200 (392) | °C(°F) | — |
Value | Units | Test Method / Conditions | |
Surface Conductivity (Σs) | 0.0037 | S/sq | ASTM D257, ASTM D4496 |
Volume Conductivity (Σv) | 0.04 | S/cm | Mil-Std-883J Method 5011.6 |
Volume Resistivity (ΡV) | 23 | Ω·cm | Mil-Std-883J Method 5011.6 |
Surface Resistivity (ΡS) | 271 | Ω/sq | ASTM D257, ASTM D4496 |
Value | Units | Test Method / Conditions | |
Dropping Point | min. 304 (min. 579) | °C(°F) | ASTM D 2265 |
Water Washout (at 38 °C, 100 °F) | 0.2 | % | ASTM D 1264 |
Evaporation Loss (22 h at 165 °C, 329 °F) | 0.3 | — | ASTM D 2595 |
Oil Separation (30 h at 165 °C, 329 °F) | 1.8 | % | ASTM D 6184 |
Worked Penetration (60 Strokes, ½ Scale) | 174 | — | ASTM D 1403 |
Emcor Rust Test, Distilled Water | 3 ⁽ᵃ⁾ | — | IP 220 |
Value | Units | Test Method / Conditions | |
Pour Point | min. -34 (min. -29) | °C(°F) | — |
Oil Viscosity Index ⁽ᵃ⁾ | min. 110 (min. 230) | °C(°F) | ASTM D 2270 |
Flash Point ⁽ᶜ⁾ | min. 290 (min. 554) | °C(°F) | ASTM D 92 |
Fire Point (ᵇ⁾ | 321 (610) | °C(°F) | ASTM D 92 |
Value | Units | Test Method / Conditions | |
Storage Temperature Limits ⁽ᵃ⁾ | -40 to 40 (-40 to 104) | °C(°F) | — |
Constant Service Temperature | -68 to 165 (-90 to 329) | °C(°F) | — |
Regulatory & Compliance
Safety & Health
- Health, Safety, and Environmental Awareness
- Please see the 847 Safety Data Sheet (SDS) for further details on transportation, storage, handling, safety guidelines, and regulatory compliance.
Packaging & Availability
- Packaging and Supporting Products
Cat. No. Packaging Net Volume Net Weight Packaged Weight 847-25ML Jar 25 mL [0.84 fl oz] 26.8 g [0.94 oz] 0.04 kg [0.09 lb] 847-1P Jar 466 mL [15.7 fl oz] 500 g [1.10 lb] 0.56 kg [1.22 lb] 847-1G Pail 3.78 L [1.00 gal] 4.05 kg [8.93 lb] 4.18 kg [9.21 lb]
Storage & Handling
- Shelf Life
- 5 Years
- Storage
- Store between -40 and 40 °C [40 and 104 °F] in dry area.