Products

Nylene Designed for use in extrusion of Tubing and Film Excellent grease resistance, toughness, and resistance to abrasion Films made from NX4797, have good barrier properties against Oxygen and Aroma typical of PA6 Meets FDA 21 CFR 177.1500 food contact requirements

Nylene Very high viscosity extrusion resin having an ASTM relative viscosity of 800 Excellent structural strength, durability, and physical properties Good melt strength and good draw-down properties which promote dimensional control for extrusion of pipe, tubing, film, and sheet Particularly recommended for the extrusion of thick slab, large rod stock, and large complex profiles Optimum processing conditions should permit for a melt temperature of 550 - 575°F at the die.

Nylene Nylon 6 based copolymer suitable for both blown and cast film coextrusion Lower melting point and is less crystalline than nylon 6 Excellent toughness, chemical resistance, transparency, and low oxygen permeability Films made using Nylene 826 exhibit superior deep draw characteristics Because Nylene 826 is polymerized using a continuous process, it has good lot-to-lot consistency.

Nylene Copolymer suitable for both blown and cast film co-extrusion, Has a lower melt point and is less crystalline than standard nylon 6 resins, Excellent toughness, chemical resistance, transparency, and low oxygen permeability, superior deep-drawing characteristics, Effective processing is achieved with extruder and die temperatures in the range of 450 - 525°F.

Nylene Nylene NX1170 is a high viscosity, extrusion grade resin containing 5% molybdenum disulfide for improved wear resistance. The abrasion resistance of nylon 6 is enhanced by the addition of molysulfide. Because of its high melt viscosity, NX1170 can be extruded into rods, tubing, thin films, many complex shapes.

Nylene Nylon 6 polymer designed for use in extrusion of tubing and film to be used in food packaging. High melt strength for shape retention Like most PA6, Nylene 615 NP has excellent grease resistance, toughness, and resistance to abrasion.

Nylene High viscosity, UV stabilized extrusion grade nylon resistant to degradation by ultraviolet light The elevated quality of UV resistance is attributed to highly uniform dispersion of 2% carbon black With an ASTM viscosity of 200, NX4301 has very good melt flow and melt strength characteristics which are important for profile extrusion Optimum processing conditions should permit for a melt temperature of 550 - 575°F at the die. (Available in black only)

Nylene High viscosity (200 RV), extrusion grade nylon 6/6 recommended for practically all types of extrusion including profile, film Has good melt flow and melt strength properties Optimum processing conditions should permit for a melt temperature of 550°F -575°F at the die

Nylene Nucleated extrusion grade suitable for cast and blown film Excellent melt stability and good melt strength, plus faster set-up for increased line speeds Superior grease resistance, toughness, resistance to abrasion, and does not absorb food odors

Nylene Nylon 6,6/6 copolymer. Nylene PAC6-135 is suitable for use in extrusion, and film applications Has the heat and chemical resistance of nylon, with the lower crystallinity typical of type 6,6/6 grades Suitable for high clarity film

Nylene Nylon 6 polymer designed for use in extrusion coating and cast and blown filmExcellent grease resistance, toughness, and resistance to abrasion.Films made from Nylene® 615 C have barrier properties against oxygen and aroma typical of nylon 6.Meets the requirements of 21 CFR 177.1500 for food contact.

Nylene High-viscosity nucleated extrusion grade, suitable for film co-extrusion, cast and blown film Excellent melt stability and strength, faster set-up for increased line speeds Superior grease resistance, toughness, resistance to abrasion, and does not absorb food odors Reduced coefficient of friction

Nylene High viscosity heat-stabilized extrusion grade for film co-extrusion and blown film Excellent melt stability and good melt strength. Excellent chemical resistance, toughness, and resistance to abrasion

Nylene Duratel MF9 is an unreinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 issuitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene Med-high viscosity nucleated extrusion grade suitable for cast and blown film Excellent melt stability and good melt strength, faster set-up for increased line speeds Superior grease resistance, toughness, resistance to abrasion, and does not absorb food odors

Nylene Higher RV version of 826 which is a special nylon copolymer suitable for both blown and cast film co-extrusion Has a lower melt point and is less crystalline than standard nylon 6 resins In addition to excellent toughness, chemical resistance, transparency, and low oxygen permeability, films exhibit superior deep-drawing characteristics Effective processing is achieved with extruder and die temperatures in the range of 450 - 525°F

Nylene Duratel MF9 is an un-reinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required

Nylene Duratel MF3 is a high-viscosity acetal co-polymer. Duratel MF3 has slightly higher toughness than standard MF9, and parts molded with MF3 should have thicker wall sections and shorter flow lengths to accommodate the higher viscosity. MF3 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene Heat stabilized, high impact modified nylon suitable for both blow-molding and extrusion. In addition to heat stabilization to prevent thermal degradation, parts molded from Nylene 764B have excellent R.T. And C.T. Impact strength right out of the mold without post conditioning. Outstanding features include high strength and high cold temperature impact. Cylinder temperatures should be in the 435 - 525°F range.

Nylene Duratel MF27 is an unreinforced high-flow acetal co-polymer. Duratel MF27 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF27 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene High viscosity, extrusion grade recommended for practically all types of extrusion including profile, film, and extrusion coating Especially recommended for flexible packaging where as a film or coating it is used for the outside layer in multi-ply film constructions Excellent melt flow and melt strength properties Optimum processing conditions should permit for a melt temperature of 550 - 575°F at the die.

Nylene Medium viscosity, extrusion grade nylon 6 resin suitable for film co-extrusion, coatings, and compounding applications Excellent melt stability and good melt strength Excellent grease resistance, toughness, resistance to abrasion, and does not absorb food odors Meets the requirements of FDA regulation 21 CFR 177.1500 for direct food contact Optimum processing conditions should provide a melt temperature of 480 - 500°F at the die

Nylene Duratel MF9 UV BK is an acetal co-polymer. Duratel MF9 UV BK has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins, while adding UV resistance for improved appearance and lifespan in exposed conditions. Duratel MF9 UV BK is suitable for such applications as clips, fasteners, and other uses where long term creep and wear resistance are required.