LNP™ COLORCOMP™ Compound I1000

Identification & Functionality

Chemical Family

Polyamides

Polymer Name

Polyamide 612 (PA 612)

Plastics & Elastomers Functions

Resin

Technologies

Plastics

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Features & Benefits

Labeling Claims

No Added PFAS

Materials Features

Excellent Aesthetics,

Good Aesthetics,

Good Surface Appearance,

High Durability,

No Added PFAS,

Unreinforced

Applications & Uses

Markets

Automotive & Transportation,

Consumer Goods,

Electrical & Electronics,

Personal Care,

Printing & Packaging

Applications

Consumer Goods — Appliances & Electronics

Automotive & Transportation — Automotive

Interior

Electrical & Electronics — Devices & Assemblies

Consumer Electronics,

Displays

Printing & Packaging — Packaging

Non-Food Consumer Packaging

Personal Care — Packaging & Accessories

Applicators & Accessories

Electrical & Electronics — Parts & Components

Connectors,

Switches & Relays

Consumer Goods — Sports & Recreation

Plastics & Elastomers End Uses

Appliances,

Automotive Applications,

Automotive Interior Parts,

Cell Phones,

Commercial Appliance,

Computer Components,

Consumer Applications,

Containers,

Displays,

Electrical Components,

Electrical/Electronic Applications,

Home Appliances,

Personal Accessories,

Sporting Goods,

Tablets

Plastics & Elastomers Processing Methods

Injection Molding

Properties

Color

Custom

Mechanical Properties

	Value	Units	Test Method / Conditions
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	100	%	ASTM D638
Tensile Stress (Yield, 5 mm/min) ¹¹	62	MPa	ISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹	4.5	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	2390	MPa	ISO 527

Physical Properties

	Value	Units	Test Method / Conditions
Specific Gravity ¹¹	1.06	—	ASTM D792
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹	1 - 3	%	ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹	1 - 3	%	ASTM D955

Thermal Properties

	Value	Units	Test Method / Conditions
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	55	°C	ASTM D648
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	135	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	62	°C	ISO 75/Af

Electrical Properties

	Value	Units	Test Method / Conditions
Volume Resistivity ¹¹	1.00E+15	Ω.cm	ASTM D257
Surface Resistivity ¹¹	1.00E+12	Ω	ASTM D257
Relative Permittivity (100 Hz) ¹¹	3.6	—	ASTM D150
Relative Permittivity (1 MHz) ¹¹	3.2	—	ASTM D150
Dissipation Factor (at 100 Hz) ¹¹	0.02	—	ASTM D150
Dissipation Factor (at at 1 kHz) ¹¹	0.02	—	ASTM D150
Dissipation Factor (at 100 kHz) ¹¹	0.014	—	ASTM D150

Injection Molding

	Value	Units	Test Method / Conditions
Drying Temperature ⁷	80	°C	—
Drying Time ⁷	4	Hrs	—
Maximum Moisture Content ⁷	0.12 - 0.2	%	—
Melt Temperature ⁷	270 - 275	°C	—
Front - Zone 3 Temperature ⁷	270 - 280	°C	—
Middle - Zone 2 Temperature ⁷	260 - 270	°C	—
Rear - Zone 1 Temperature ⁷	255 - 265	°C	—
Mold Temperature ⁷	65 - 95	°C	—
Back Pressure ⁷	0.2 - 0.3	MPa	—
Screw Speed ⁷	30 - 60	rpm	—

Flame Characteristics

	Value	Units	Test Method / Conditions
Oxygen Index (LOI)	27	%	ISO 4589

Note

• ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
• ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
• ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

 

Packaging & Availability

Regional Availability

• Americas
• Asia
• Europe
• North America