LNP™ LUBRICOMP™ Compound JFL36

1 of 365 products in this brand
LNP LUBRICOMP JFL36 compound is based on Polyethersulfone (PES) resin containing 30% glass fiber, 15% PTFE. Added features of this grade include: Wear Resistant.

Polymer Name: Polyethersulfone (PES)

Processing Methods: Injection Molding

Fillers Included: Glass Fiber, PTFE

Additives Included: Flame Retardant, Lubricant (PTFE)

Technical Data Sheet

Knowde Enhanced TDS

Identification & Functionality

Chemical Family
Fillers Included
Plastics & Elastomers Functions
Technologies

Features & Benefits

Applications & Uses

Plastics & Elastomers Processing Methods

Properties

Mechanical Properties
ValueUnitsTest Method / Conditions
Tensile Stress (Break, 5 mm/min) ¹¹117MPaISO 527
Tensile Stress (Break) ¹¹128MPaASTM D638
Tensile Stress (Break) ¹¹89MPaISO 527
Tensile Strain (Break, 5 mm/min) ¹¹1.6%ISO 527
Tensile Strain (Break) ¹¹1.9%ASTM D638
Tensile Strain (Break) ¹¹1.5%ISO 527
Tensile Modulus (at 1 mm/min) ¹¹9800MPaISO 527
Tensile Modulus (at 1 mm/min) ¹¹9540MPaISO 527
Tensile Modulus (at 50 mm/min) ¹¹10180MPaASTM D638
Flexural Stress (Yield, at 2 mm/min) ¹¹160MPaISO 178
Flexural Stress ¹¹179MPaASTM D790
Flexural Stress ¹¹138MPaISO 178
Flexural Modulus (at 2 mm/min) ¹¹7700MPaISO 178
Flexural Modulus ¹¹9920MPaASTM D790
Flexural Modulus ¹¹10840MPaISO 178
Physical Properties
ValueUnitsTest Method / Conditions
Mold Shrinkage (on Tensile Bar, flow) ᵍ ¹¹0.15 - 0.35%SABIC method
Wear Factor Washer ¹¹6010^-10 in^5-min/ft-lb-hrASTM D3702 Modified: Manual
Dynamic COF ¹¹0.46ASTM D3702 Modified: Manual
Static COF ¹¹0.36ASTM D3702 Modified: Manual
Density ¹¹1.69g/cm³ISO 1183
Density ¹¹1.7g/cm³ASTM D792
Density ¹¹1.7g/cm³ISO 1183
Moisture Absorption (at 23°C, 50% RH, 24hrs) ¹¹0.29%ASTM D570
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹0.1 - 0.4%ASTM D955
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹0.1 - 0.3%ISO 294
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹0.3 - 0.6%ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹0.3 - 0.6%ISO 294
Moisture Absorption (at 23°C, 50% RH) ¹¹0.5%ISO 62
Thermal Properties
ValueUnitsTest Method / Conditions
Coefficient of Thermal Expansion (at 23°C to 60°C, flow) ¹¹0.0000181/°CISO 11359-2
Coefficient of Thermal Expansion (at 23°C to 60°C, xflow) ¹¹0.0000491/°CISO 11359-2
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹223°CISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹219°CISO 75/Af
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹210°CISO 75/Af
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹207°CASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹0.00002281/°CASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹0.00002281/°CISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹0.00003521/°CASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹0.00003521/°CISO 11359-2
Impact Properties
ValueUnitsTest Method / Conditions
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹30kJ/m²ISO 180/1U
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹24kJ/m²ISO 180/1U
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹9kJ/m²ISO 180/1A
Izod Impact (Unnotched, at 23°C) ¹¹363J/mASTM D4812
Izod Impact (Notched, at 23°C) ¹¹85J/mASTM D256
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹9JASTM D3763
Multi-Axial Impact ¹¹2JISO 6603
Injection Molding
ValueUnitsTest Method / Conditions
Drying Temperature ⁷120 - 150°C
Drying Time ⁷4Hrs
Maximum Moisture Content ⁷0.05%
Melt Temperature ⁷355 - 370°C
Front - Zone 3 Temperature ⁷370 - 380°C
Middle - Zone 2 Temperature ⁷360 - 370°C
Rear - Zone 1 Temperature ⁷345 - 355°C
Mold Temperature ⁷140 - 150°C
Back Pressure ⁷0.3 - 0.7MPa
Screw Speed ⁷60 - 100rpm
Note
  • ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
  • ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
  • ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
 

Packaging & Availability

Regional Availability
  • Asia
  • Europe
  • North America