LNP™ LUBRICOMP™ Compound RAL23S

1 of 365 products in this brand
SABIC's Specialties Business LNP LUBRICOMP RAL23S compound is based on Nylon 6/6 resin containing 10% PTFE, 15% aramid fiber. Added features of this grade include: Heat Stabilized, Wear Resistant.

Polymer Name: Polyamide 66 (PA 66)

Processing Methods: Injection Molding

Fillers Included: Aramid Fiber, PTFE

Additives Included: Heat Stabilizer, Lubricant (PTFE)

Flexural Modulus: 3930.0 - 3930.0 MPa

Technical Data Sheet

Knowde Enhanced TDS

Identification & Functionality

Chemical Family
Fillers Included
Plastics & Elastomers Functions
Technologies

Features & Benefits

Applications & Uses

Plastics & Elastomers Processing Methods

Properties

Mechanical Properties
ValueUnitsTest Method / Conditions
Tensile Stress (Break) ¹¹89MPaASTM D638
Tensile Stress (Break) ¹¹85MPaISO 527
Tensile Strain (Break) ¹¹6.3%ISO 527
Tensile Strain (Break) ¹¹5.9%ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹3680MPaASTM D638
Flexural Stress ¹¹131MPaASTM D790
Flexural Stress ¹¹107MPaISO 178
Flexural Modulus ¹¹3500MPaISO 178
Flexural Modulus ¹¹3930MPaASTM D790
Tensile Modulus (at 1 mm/min) ¹¹3800MPaISO 527
Physical Properties
ValueUnitsTest Method / Conditions
Density ¹¹1.23g/cm³ISO 1183
Density ¹¹1.24g/cm³ASTM D792
Mold Shrinkage (flow, 24 hrs) ᵍ ¹¹1 - 1.5%ASTM D955
Mold Shrinkage (xflow, 24 hrs) ᵍ ¹¹1.2 - 1.7%ASTM D955
Wear Factor Washer ¹¹2310^-10 in^5-min/ft-lb-hrASTM D3702 Modified: Manual
Dynamic COF ¹¹0.38ASTM D3702 Modified: Manual
Static COF ¹¹0.32ASTM D3702 Modified: Manual
Thermal Properties
ValueUnitsTest Method / Conditions
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹171°CASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹0.0000671/°CASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹0.0000681/°CISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹0.0000971/°CASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹0.0000981/°CISO 11359-2
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹246°CISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹160°CISO 75/Af
Impact Properties
ValueUnitsTest Method / Conditions
Izod Impact (Unnotched, at 23°C) ¹¹534J/mASTM D4812
Izod Impact (Notched, at 23°C) ¹¹46J/mASTM D256
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹37kJ/m²ISO 180/1U
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹4kJ/m²ISO 180/1A
Injection Molding
ValueUnitsTest Method / Conditions
Drying Temperature ⁷80°C
Drying Time ⁷4Hrs
Maximum Moisture Content ⁷0.15 - 0.25%
Melt Temperature ⁷275 - 290°C
Front - Zone 3 Temperature ⁷295 - 305°C
Middle - Zone 2 Temperature ⁷280 - 295°C
Rear - Zone 1 Temperature ⁷265 - 275°C
Mold Temperature ⁷80 - 95°C
Back Pressure ⁷0.2 - 0.3MPa
Screw Speed ⁷30 - 60rpm
Note
  • ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
  • ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
  • ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
 

Packaging & Availability

Regional Availability
  • Americas
  • Asia
  • Europe
  • North America