NORYL™ Resin N190X

1 of 145 products in this brand
SABIC's Specialties Business NORYL™ N190X resin is a non-reinforced blend of polyphenylene ether (PPE) + polystyrene (PS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 3mm and V0 at 1.5mm along with a UL746C Outdoor Suitability rating of F1. NORYL™ N190X resin offers strong electrical performance, low moisture absorption, dimensional stability, and hydrolytical stability. This material is an excellent candidate for indoor and outdoor electrical enclosure, wall plate / switch, connector, and solar / photovoltaic junction box applications.

Polymer Name: PPO/PS Alloy

Processing Methods: Injection Molding, Laser Sintering (SLS)

Density: 1130.0 - 1130.0 kg/m³

Flexural Modulus: 2350.0 - 2350.0 MPa

Technical Data Sheet

Knowde Enhanced TDS

Identification & Functionality

Polymer Name
Plastics & Elastomers Functions
Technologies

Features & Benefits

Applications & Uses

Plastics & Elastomers Processing Methods

Properties

Mechanical Properties
ValueUnitsTest Method / Conditions
Tensile Stress (Yield, Type I, 50 mm/min) ¹¹60MPaASTM D638
Tensile Stress (Break, Type I, 50 mm/min) ¹¹47MPaASTM D638
Tensile Strain (Yield, Type I, 50 mm/min) ¹¹3.6%ASTM D638
Tensile Strain (Break, Type I, 50 mm/min) ¹¹9%ASTM D638
Tensile Modulus (at 50 mm/min) ¹¹2580MPaASTM D638
Flexural Stress (Yield, 1.3 mm/min, 50 mm span) ¹¹98MPaASTM D790
Flexural Stress (Yield, 2.6 mm/min, 100 mm span) ¹¹91MPaASTM D790
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹2500MPaASTM D790
Flexural Modulus (at 2.6 mm/min, 100 mm span) ¹¹2300MPaASTM D790
Hardness (Rockwell R) ¹¹120ASTM D785
Taber Abrasion (CS-17, 1 kg) ¹¹76mg/1000cyASTM D1044
Tensile Stress (Yield, 50 mm/min) ¹¹58MPaISO 527
Tensile Stress (Break, 50 mm/min) ¹¹50MPaISO 527
Tensile Strain (Yield, 50 mm/min) ¹¹3.2%ISO 527
Tensile Strain (Break, 50 mm/min) ¹¹9.2%ISO 527
Tensile Modulus (at 1 mm/min) ¹¹2600MPaISO 527
Flexural Stress (Yield, at 2 mm/min) ¹¹8.70E+01MPaISO 178
Flexural Modulus (at 2 mm/min) ¹¹2350MPaISO 178
Physical Properties
ValueUnitsTest Method / Conditions
Specific Gravity ¹¹1.13ASTM D792
Water Absorption (at 23°C, 24hrs) ¹¹0.08%ASTM D570
Mold Shrinkage (flow, 3.2 mm) ᵍ ¹¹0.5 - 0.7%SABIC method
Melt Flow Rate (at 250°C, 10.0 kgf) ¹¹19.3g/10 minASTM D1238
Melt Volume Rate (at 280°C, 5.0 kg) ¹¹23cm³/10 minISO 1133
Melt Flow Rate (at 280°C, 5.0 kgf) ¹¹20g/10 minASTM D1238
Thermal Properties
ValueUnitsTest Method / Conditions
Vicat Softening Temperature (Rate B/50) ¹¹104°CASTM D1525
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹95°CASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹78°CASTM D648
Heat Deflection Temperature (at 1.82 MPa, 6.4 mm, Unannealed) ¹¹86°CASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹0.0000771/°CASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹0.0000811/°CASTM E831
Thermal Conductivity ¹¹0.24W/m-°CASTM C177
Vicat Softening Temperature (Rate B/120) ¹¹107°CISO 306
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹95°CISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹82°CISO 75/Af
Relative Temperature Index (Electrical) ᵖ ¹¹95°CUL 746B
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹80°CUL 746B
Relative Temperature Index (Mechanical without impact) ᵖ ¹¹95°CUL 746B
Electrical Properties
ValueUnitsTest Method / Conditions
Volume Resistivity ¹¹1.80E+16Ω.cmASTM D257
Dielectric Strength (in oil, at 3.2mm) ¹¹19.2kV/mmASTM D149
Relative Permittivity (100 Hz) ¹¹2.74ASTM D150
Relative Permittivity (100 kHz) ¹¹2.6ASTM D150
Dissipation Factor (at 100 Hz) ¹¹0.013ASTM D150
Dissipation Factor (at 100 kHz) ¹¹0.0055ASTM D150
High Voltage Arc Track Rate (PLC) ¹¹4PLC CodeUL 746A
Comparative Tracking Index (UL, PLC) ¹¹1PLC CodeUL 746A
High Ampere Arc Ignition (PLC 0) ¹¹min. 6mmUL 746A
High Ampere Arc Ignition (PLC 2) ¹¹min. 1.5mmUL 746A
Hot Wire Ignition (PLC 1) ¹¹min. 6mmUL 746A
Hot Wire Ignition (PLC 2) ¹¹min. 1.5mmUL 746A
Arc Resistance (Tungsten, PLC) ¹¹7PLC CodeASTM D495
Impact Properties
ValueUnitsTest Method / Conditions
Izod Impact (Unnotched, at 23°C) ¹¹720J/mASTM D4812
Izod Impact (Notched, at 23°C) ¹¹293J/mASTM D256
Izod Impact (Unnotched, at -30°C) ¹¹100J/mASTM D4812
Izod Impact (Notched, at -30°C) ¹¹100J/mASTM D256
Instrumented Dart Impact Energy (Peak, at 23°C) ¹¹50JASTM D3763
Instrumented Dart Impact Total Energy (at 23°C) ¹¹50JASTM D3763
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹20kJ/m²ISO 180/1A
Charpy Impact (Notched, at 23°C) ¹¹20kJ/m²ISO 179/2C
Injection Molding
ValueUnitsTest Method / Conditions
Drying Temperature ⁷75 - 80°C
Drying Time ⁷3 - 4Hrs
Drying Time (Cumulative) ⁷8Hrs
Maximum Moisture Content ⁷0.02%
Melt Temperature ⁷250 - 275°C
Nozzle Temperature ⁷250 - 275°C
Front - Zone 3 Temperature ⁷240 - 275°C
Middle - Zone 2 Temperature ⁷225 - 270°C
Rear - Zone 1 Temperature ⁷215 - 265°C
Mold Temperature ⁷55 - 75°C
Back Pressure ⁷0.3 - 0.7MPa
Screw Speed ⁷20 - 100rpm
Shot to Cylinder Size ⁷30 - 70%
Vent Depth ⁷0.038 - 0.051mm
Flame Characteristics
ValueUnitsTest Method / Conditions
UL Recognized (94-5VA Flame Class Rating) ʳmin. 3mmUL 94
UL Recognized (94HB Flame Class Rating) ʳmin. 1mmUL 94
UL Recognized (94V-0 Flame Class Rating) ʳmin. 1.5mmUL 94
Glow Wire Flammability Index (at 1 mm) ʳ960°CIEC 60695-2-12
Glow Wire Flammability Index (at 2 mm) ʳ960°CIEC 60695-2-12
Glow Wire Flammability Index (at 3 mm) ʳ960°CIEC 60695-2-12
Glow Wire Ignitability Temperature (at 1.0 mm) ʳ800°CIEC 60695-2-13
Glow Wire Ignitability Temperature (at 2.0 mm) ʳ775°CIEC 60695-2-13
Glow Wire Ignitability Temperature (at 3.0 mm) ʳ775°CIEC 60695-2-13
UV-light (Water exposure/immersion) ʳF1UL 746C
Oxygen Index (LOI) ʳ39%ASTM D2863
Note
  • ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
  • ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
  • ʳ UL Ratings shown on the technical datasheet might not cover the full range of thicknesses, colors and regions. For details, please see the UL Yellow Card.
  • ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
  • ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
 

Regulatory & Compliance

Certifications & Compliance

Packaging & Availability

Regional Availability
  • Americas
  • Asia
  • North America