Tasnee HDPE IM2050

1 of 7 products in this brand
Tasnee HD IM2050 is a High Density Polyethylene (HDPE), multimodal resin manufactured by slurry process using advanced cascade process technology. Tasnee HD IM2050 is easy to process on injection and compression molding equipment. This grade has very good stiffness and toughness, high ESCR and exceptional organoleptic properties.

Polymer Name: High Density Polyethylene (HDPE)

Processing Methods: Compression Molding, Injection Molding

Melt Flow Index: 2.1 - 2.1 g/10 min, 6.3 - 6.3 g/10 min

Similar Products

  • TypeDocument Name
View All Documents

Knowde Enhanced TDS

Identification & Functionality

Plastics & Elastomers Functions
Technologies

Features & Benefits

Applications & Uses

Plastics & Elastomers End Uses
Plastics & Elastomers Processing Methods
Typical Applications
Caps & closures for water, CSD and others food & non-food applications.

Properties

Physical Form
Mechanical Properties
ValueUnitsTest Method / Conditions
Charpy Notched Impact Strength (Note: notch A, Type 1, at -30°C)5kJ/m2ISO 179
Compression molding melt temperature180 - 210°C
ESCRmin. 9hrInternal method
Injection Molding Melt Temperature190 - 240°C
Ball Indentation Hardness (H132/30)51MPaISO 2039-1
Shore Hardness (Shore D)62ISO 868
Tensile Modulus1150MPaISO 527-1,-2
Tensile Strain at Yield10%ISO 527-1,-2
Tensile Stress at Yield30MPaISO 527-1,-2
Physical Properties
ValueUnitsTest Method / Conditions
Density0.953g/cm3ISO 1183
Melt Flow Rate (190°C / 2.16kg)2.1g/10 minISO 1133
Melt Flow Rate (190°C / 5kg)6.3g / 10 minISO 1133
Vicat Softening Temperature (VST/B/50K/h (50N))75°CISO 306
Note
The above properties values are not to be construed as specifications.

Regulatory & Compliance

Food Contact
The material is manufactured to the highest standards but, special requirements apply to certain applications, such as food contact end-use. For specific information on regulatory compliance, please contact TASNEE below or our local representative in your area.

Safety & Health

Safety
Workers should be protected from the possibility of skin or eye contact with molten polymer. As minimum precaution, safety glasses and heat resistance gloves are suggested to prevent mechanical or thermal injury to eyes and hands. Molten polymer exceeding processing condition requirements may degrade and release, fumes, vapors and unpleasant odor. In higher concentrations they may cause irritation of the mucus membranes. Fabrication areas should be ventilated to carry away fumes and vapors. Legislation on the control of emissions and pollution prevention must be observed. If the principles of sound manufacturing practice are adhered to and the place of work is well ventilated, no health hazards are involved in processing the material. The material may burn when supplied with excess heat and oxygen. It should be handled and stored away from contact with direct flames and/or ignition sources. In burning the material generates considerable heat and may release a dense black smoke. Fires should be extinguished by heavy foams or dry powder. For further information about safety in handling and processing please refer to the Material Safety Data Sheet (MSDS).

Packaging & Availability

Packaging Type

Storage & Handling

Storage
The material is packed in 25 kg bags or in bulk containers protecting it from contamination. Storage time of material longer than 6 months may have a negative influence on the quality of the final product. It is generally recommended to convert all materials latest within 6 months from delivery date. The material is subjected to degradation by ultra-violet radiation or by high storage temperatures. Therefore the material must be protected from direct sunlight, temperatures above 40°C and high atmospheric humidity during storage. Further unfavorable storage conditions are large fluctuations in ambient temperature and high atmospheric humidity. TASNEE will not give any warranty to unfavorable storage conditions which may lead to quality deterioration such as color change, bad smell and inferior product performance.