THE BREWER COMPANY COLD PROCESS ADHESIVE

Identification & Functionality

Product Type

Coating

Technologies

Ready-to-Use Products

Product Families

Ready-to-Use Products — Adhesives & Sealants

Other Adhesives & Sealants

Features & Benefits

Labeling Claims

Asbestos-free,

Low VOC

Ready-to-Use Product Features

Good Sagging Resistance,

Low VOC

Features

• Cold applied by brush, squeegee or airless spray equipment.
• Eliminates the use of kettles and open flames.
• Cures slowly so that the top ply can relax and flatten without breaking the bond with the underlying substrate.
• Resistant to running and sagging at elevated rooftop temperatures.
• Non-Asbestos.

Applications & Uses

Markets

Building & Construction

Applications

Building & Construction — Other Building & Construction Applications

Application Method

Brush,

Spray,

Wipe

Compatible Substrates & Surfaces

Asphalt

Application & Uses

Uses:

• Substrate adhesive for built-up roofing systems (asphalt).
• Interply adhesive for modified bitumen sheets.
• Flood coat for receiving gravel.

Applications:

• Ready to apply.
• Do not heat.
• Do not thin.

Surface Preparation

• All work surfaces must be clean, dry, free of dirt, dust, debris, oils, loose and/or embedded gravel, un-adhered coatings, deteriorated membranes, and other contaminants that may result in a surface that is not sound.
• All necessary repairs must be completed before application to ensure optimum performance.
• All surfaces must be free of frost, snow and ice.

Application Directions

BUR:

• Apply at a rate of approximately 2 - 4 gallons per square, depending on the surface irregularities.
• Roll out and embed the first ply.
• Apply an additional layer or adhesive at an interply rate of 1 - 2 gallons per square, followed by another ply sheet.
• Repeat, until the desired number of plies is achieved.
• Topcoat at a rate of 2 gallons per square if a glaze coat is desired; or use 4 - 6 gallons per square to apply gravel or mineral surfacing.

Modified Bitumen:

• Apply to the prepared surface at a rate of approximately 1 - 2 gallons per square, depending on the surface irregularities.
• Roll out and embed the modified bitumen sheet.
• Broom into place, assuring that the membrane conforms to the surface and that no bridging or air pockets exist.
• Open time is 30 - 45 minutes; dry time is 6 - 8 hours to touch.

Application Precautions

• Do not use with or on 100% rubber or plastic substrates.
• Do not use on or with products containing coal tar.
• Do not apply to damp or wet surfaces.
• Do not use where this product may come in contact with potable water.
• Do not thin.
• Exterior use only.

Clean Up

• Immediately rinse/flush equipment and tools with mineral spirits after use, exercising all flammable liquid precautions.
• Use waterless hand cleaner on the skin.

Properties

Color

Black

Typical Properties

	Value	Units	Test Method / Conditions
Weight Per Gallon	8.2 - 8.6	lbs.	D6511
Solids by Weight	78 - 82	%	D6511
Solids by Volume	75 - 80	%	D6511
Viscosity (200rpm)	700 - 1100	grams	Stormer
Flash Point	min. 105	°F	PMCC
Drying Time (Touch, 70°F/50% R.H.)	1.0	Hour	—
VOC	max. 300	gm/liter	EPA Method 24A

Regulatory & Compliance

Compliance

• Meets current Volatile Organic Compounds (VOC) regulations.
• Meets ASTM D3019, Type III, Metro Dade, UL Classified.

Packaging & Availability

Packaging Type

Drums,

Pails

Packaging

• 5-gallon pails (44 lbs.)
• 55-gallon drums (497 lbs.)

Storage & Handling

Shelf Life (70°F/50% R.H.)

1 year