Products

ELASTOSIL® LR 3842/60 A/B is a low-oil-bleeding liquid silicone rubber from the ELASTOSIL® LR 3842 series. It is a paste-like, easily  pigmentable, two-component product with short curing times. Shortly after the curing process, a thin oil film with lubricating properties forms on the surface of the vulcanizates. The vulcanizates are opaque and exhibit good mechanical and electrical properties, as well as very low compression sets.

SILPURAN® 6000/30 A/B is a paste-like, easily pigmentable two-component compound with short curing times. Its vulcanizates are noted for their high transparency and excellent mechanical and electrical properties. SILPURAN® 6000/30 A/B is designed for medical applications in compliance with the Wacker Silicones Health Care Policy, including implantation for less than 30 days.

SILPURAN® 6000/05 A/B is a paste-like, easily pigmentable two-component compound with short curing times. Its vulcanizates are noted for their high transparency and excellent mechanical and electrical properties. SILPURAN® 6000/05 A/B is designed for medical applications in compliance with Wacker Silicones' health care policy. Please note that this material has use restrictions according to Wacker Silicone's health care policy. In particular, contact with body tissue or blood is not permitted.

ELASTOSIL® R 500/50 OH is a peroxide-cured high-consistency silicone rubber (HCR) for general-purpose applications. This product can be used within a temperature range of -55 °C to +210 °C. The addition of heat stabilizers at service temperatures of more than 180°C is recommended.

BELSIL® eco REG 1102 resin elastomer gel is a non-emulsifying silicone copolymer network blended with a non-volatile, low-viscosity dimethicone, based on renewable raw materials according to "TÜV NORD Standard REDcert²". It is a transparent gel that provides a very pleasant sensory experience both during application and afterwards. BELSIL® eco REG 1102 can act as a thickener in formulations while delivering a smooth application. In addition, it exhibits shear-thinning behavior. This attribute allows for the formulation of cosmetic products that spread easily during application and facilitates the incorporation of pigments into a formulation.

ELASTOSIL® R 756/70 OH is a peroxide-cured high-consistency silicone rubber whose vulcanizates possess excellent resistance to hot air, particularly after the addition of a heat stabilizer. The vulcanizates of this product show good tear resistance, a low compression set, and are highly elastic.

ELASTOSIL® R 750/50 OH is a high-consistency silicone rubber (HCR) known for its exceptional resistance to high temperatures, oxygen, and dry heat. The vulcanizates produced from this product exhibit excellent performance under extreme conditions. It is specifically designed for applications that require resistance to high temperatures and is suitable for extrusion processes.

ELASTOSIL® R 500/40 OH is a peroxide-cured high-consistency silicone rubber (HCR) for general-purpose applications. This product can be used within a temperature range of -55 °C to +210 °C. The addition of heat stabilizers at service temperatures of more than 180°C is recommended.

ELASTOSIL® AUX Stabilizer H4 is a ready-to-use additive comprising a heat-stabilizing filler and a reactive silicone polymer, which is a typical ingredient of ELASTOSIL® high-consistency rubber grades. This ensures that the batch is incorporated into the elastomer network during vulcanization and thus does not show any migration.

ELASTOSIL® R 865/60 S provides a wide range of functional advantages. This material guarantees superior rebound resilience and minimal compression set. It can be easily pigmented using ELASTOSIL® PT Pigment Pastes and exhibits favorable processing characteristics. The various grades available, including ELASTOSIL® R 865/40 to ELASTOSIL® R 865/70, can be blended in any proportion to achieve intermediate hardness levels.

ELASTOSIL® R 865/50 S provides various functional advantages. This material delivers superior rebound resilience and minimal compression set. The compounds can be easily pigmented using ELASTOSIL® PT Pigment Pastes and exhibit favorable processing characteristics. The different grades available, ranging from ELASTOSIL® R 865/40 to ELASTOSIL® R 865/70, can be blended in any proportion to achieve intermediate hardness levels.

ELASTOSIL® R 500/70 OH is a peroxide-cured high-consistency silicone rubber (HCR) for general-purpose applications. This product can be used within a temperature range of -55 °C to +210 °C. The addition of heat stabilizers at service temperatures of more than 180°C is recommended.

ELASTOSIL® RT 624 "4S" A/B VS is a pourable, two-component thermal curing silicone specifically designed for fuel cell sealing applications. It features addition curing and offers excellent bonding and sealing capabilities, making it suitable for use in various applications such as cured-in-place gaskets (dry type) and fuel cells.

ELASTOSIL® AUX Stabilizer H1 is a ready-to-use additive comprising a heat-stabilizing filler and a reactive silicone polymer, which is a typical ingredient of ELASTOSIL® high-consistency rubber grades. This ensures that the batch is incorporated into the elastomer network during vulcanization and thus does not show any migration.

SEMICOSIL® 961 TC A/B is a shear-thinning, easy-dispensing, non-slump, two-part silicone rubber that cures at room temperature. It transforms into a soft and tacky rubber with excellent thermal conductivity. Specifically designed as an interface material, SEMICOSIL® 961 TC A/B is ideal for heat sink applications in the electronics industry.

ELASTOSIL® R 401/60 KX is a high-consistency silicone rubber (HCR). Vulcanizates cured with peroxide made from this compound exhibit a unique combination of characteristics. It is noted for its good flexibility, high transparency, and mechanical properties. The compound is easily pigmented with ELASTOSIL® Color Paste PT and has good processing characteristics.

SEMICOSIL® 962 TC A/B is a gap filler paste material with excellent thermal conductivity. It is a two-part silicone rubber that is shear-thinning, easy to dispense, and non-slump. This addition-curing formulation cures at room temperature, resulting in a soft, flexible, and tacky rubber with outstanding thermal conductivity properties.

ELASTOSIL® AUX Stabilizer H2 is a ready-to-use silicone rubber additive compound containing a heat-stabilizing filler. Thanks to its paste character, ELASTOSIL® AUX Stabilizer H2 can easily be incorporated into ELASTOSIL® R and R plus mixtures on two-roll mills. It is used to extend the service life of silicone elastomers at temperatures above 170°C.

ELASTOSIL® R 500/60 OH is a peroxide-cured high-consistency silicone rubber (HCR) for general-purpose applications. This product can be used within a temperature range of -55 °C to +210 °C. The addition of heat stabilizers at service temperatures of more than 180°C is recommended.

ELASTOSIL® R 771/70 OH is a peroxide-cured high-contrast rubber silicone for the manufacture of flame retardant products, particularly designed for railway applications. The product has been tested according to EN 45545-2 requirement sets R1, R7 (HL2). The color of the rubber base is white.

SEMICOSIL® 9672 TC is a thermally conductive gap filler silicone material designed for heat sink applications in the electronics industry. It is a shear-thinning, non-slump, two-part silicone gel that cures at room temperature to a soft gel with excellent thermal conductivity.

ELASTOSIL® N 2137 is a non-slump, one-part silicone rubber for sealing and bonding applications. When exposed to air moisture, it cures at room temperature to yield a permanently flexible silicone rubber with excellent heat resistance. Fully vulcanized ELASTOSIL® N 2137 shows long-term stability against weathering, moisture, and UV radiation. The silicone elastomer may continuously be exposed to constantly changing climatic conditions, UV radiation, and temperatures as high as 180 °C (356 °F) without damage.

ELASTOSIL® R 805/75 OH is a high-consistency silicone rubber (HCR) that produces vulcanizates with excellent resistance to engine oils and aggressive mineral oils, even at high temperatures. It is an oil-resistant, peroxide-curing silicone rubber. The vulcanizates exhibit good mechanical properties and a low compression set.

WACKER® 121 - Aquarium is a high-quality silicone sealant specifically formulated for the construction of aquariums and various industrial applications. This one-part, acid-curing sealant offers excellent mechanical properties and a high curing rate. When exposed to atmospheric moisture at room temperature, WACKER® 121 - Aquarium undergoes curing, resulting in a permanently flexible silicone rubber.

SEMICOSIL® 9671 TC2 A/B is a thermal conductive gap filler silicone material used in heat sink applications for the electronics industry. It is a shear-thinning, easy-dispensing, non-slump, addition-curing, two-part silicone rubber that cures at room temperature. This material is specifically designed to enhance heat dissipation and provide efficient thermal management in electronic devices. SEMICOSIL® 9671 TC2 A/B is ideal for filling gaps and ensuring effective heat transfer in heat sink applications.

ELASTOSIL® R 502/75 OH is a peroxide-crosslinking HCR silicone for the manufacture of silicone-insulated safety cables that maintain circuit integrity. In case of fire, ELASTOSIL® R 502/75 OH forms a ceramic-like layer with high insulation resistance, good mechanical stability, and low smoke formation.

ELASTOSIL® R 752/70 OH is a high-consistency silicone rubber (HCR) known for its unique properties. The vulcanizates produced from this product exhibit very low rebound resilience and high damping capability. It is particularly suitable for the manufacturing of low-modulus rubber articles using compression, transfer, or injection molding techniques.

ELASTOSIL® AUX Stabilizer H6 is a ready-to-use additive comprising a heat-stabilizing filler and a reactive silicone polymer, which is a typical ingredient of ELASTOSIL® high-consistency rubber grades. This ensures that the batch is incorporated into the elastomer network during vulcanization and thus does not show any migration.

WACKER® Catalyst T 77 is a standard curing agent specifically designed for condensation curing RTV-2 silicones. When combined with base compounds from the ELASTOSIL® RT or ELASTOSIL® M series, it forms a durable and self-bonding silicone rubber upon curing. This catalyst is in the form of a non-slump paste, ensuring ease of application. It is recommended to use a mixing ratio of 10:1 with the base compounds for optimal results.

ELASTOSIL® R 701/50 OH is a high-consistency silicone rubber (HCR) grade for extrusion and molding applications. The compound is recommended for all kinds of seals that come into contact with mineral oil. ELASTOSIL® R 701/50 OH is used especially when low compression set is crucial for achieving good seal properties. It may also be used for making a high-quality silicone-rubber-covered roller.

WACKER® Catalyst T 77 Plus is a standard curing agent designed for condensation curing RTV-2 silicones. When used in conjunction with a base compound from the ELASTOSIL® RT or ELASTOSIL® M product series, it results in the formation of a durable and self-bonding silicone rubber upon curing. This catalyst offers the advantage of very fast curing at room temperature, and the curing speed can be adjusted by varying the mixing ratio.

ELASTOSIL® R 700/40 OH is a high-consistency silicone rubber (HCR) grade for extrusion and molding applications. It provides good resistance to oil and fat. Postcured parts made from this material can be used for food contact applications and are suitable for use under the recommendation "XV. Silicones" of the BfR and FDA 177.2600. However, it is important to observe any given limitations on extractable and volatile substances.

ELASTOSIL® AUX Stabilizer H3 is a ready-to-use additive comprising a heat-stabilizing filler and a reactive silicone polymer, which is a typical ingredient of ELASTOSIL® high-consistency rubber grades. This ensures that the batch is incorporated into the elastomer network during vulcanization and thus does not show any migration.

ELASTOSIL® R 750/60 OH is a high-consistency silicone rubber (HCR) known for its exceptional resistance to high temperatures, oxygen, and dry heat. The vulcanizates produced from this product exhibit excellent performance under extreme conditions. It is specifically designed for applications that require resistance to high temperatures and is suitable for extrusion processes.

SEMICOSIL® 9981 TC is a one-part, thermally conductive paste with electrical conductivity that cures into a gap-filling silicone. The thermal paste efficiently fills the finest gaps of heat-generating and ablating substrates, minimizing contact resistance. The thermal resistance is minimized due to an exceptional thermal conductivity of 10 W/mK, in combination with the possibility of reducing bond line thickness to 10 μm.

ELASTOSIL® AUX Stabilizer H6 F is a ready-to-use additive comprising a heat-stabilizing filler and a reactive silicone polymer, which is a typical ingredient of ELASTOSIL® high-consistency rubber grades. This ensures that the batch is incorporated into the elastomer network during vulcanization and thus does not show any migration.