Products in Agricultural Films: Dimensional Stability

Talc HFM 25 is sub-microns particle size platy talc with a high surface area & high aspect ratio to provide excellent barrier properties. During injection molding, these talcs act as ideal reinforcing fillers which provide greater stiffness & impact strength better dimensional stability. It is compatible with all thermoplastics & thermosets.

VTEC™ BG21 is a High temperature resistance and it is Superior mechanical properties

BARLOG plastics GmbH Kebaform® / C 901 TS is a specially modified type, which is characterized by excellent sliding and wear properties. Despite the highly efficient modification with PTFE and a special silicone oil, Kebaform® / C 901TS has excellent mechanical properties. Kebaform® / C 901TS is used wherever high demands are placed on wear resistance, uniformity of friction behavior under changing conditions and low noise levels, and at the same time the mechanical property profile of a technical construction material is required. Kebaform® / 901TS is particularly suitable for sliding pairings with changing operating conditions, e.g. B. When starting behavior without stick-slip effect is just as required as high wear resistance over the entire service life.

POM copolymer unreinforced, medium viscosity, tribologically modified, optimized sliding and wear behavior

BARLOG plastics GmbH Kebablend® / WR XB 111001/12 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

POM-MD30, POM copolymer unreinforced, medium viscosity, 30% mineral-reinforced

POM-MD30, POM copolymer, medium viscosity, 30% mineral-reinforced

POM copolymer unreinforced, medium viscosity, tribologically modified, optimized sliding and wear behavior

PBT-GF20, PBT, 20% glass fiber reinforced, approved for use in food contact

POM-I, POM copolymer unreinforced, medium viscosity, impact modified

POM-I, POM copolymer unreinforced, medium viscosity, impact modified, reduced emissions for automotive interior applications

Acetal-C + PTFE is a high-quality engineering plastic material.

POM-CF20, POM copolymer, medium viscosity, carbon fiber reinforced, electrically conductive

BARLOG plastics GmbH Kebablend® / WR XB 111001/2 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

POM copolymer unreinforced, medium viscosity, electrically conductive

Teijinconex® raw white fiber is a natural cluster of meta-aramid fibers that have not been treated for color.

BARLOG plastics GmbH Kebablend® / WR 02/2110 is a special compound based on POM homopolymer, which has very good sliding behavior and high wear resistance. The material has medium strength and a high elongation at break and, compared to POM copolymer, an increased melting temperature and heat resistance.

POM copolymer unreinforced, very low viscosity

POM copolymer unreinforced, medium viscosity, tribologically modified, optimized sliding and wear behavior

Next Nylon 6 Industrial Series NG15-02JBK is PA6 Glass Fiber Reinforced Black Compound

KEBABLEND / WR XB 111001/5 is a special compound based on POM, which has very good sliding behavior and high wear resistance.

BARLOG plastics GmbH Kebaform® / C 25 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Kebaform® / C 25 H improves the sliding and wear behavior solely by modifying the polymer chain and there is no reduction in mechanical properties due to the addition of tribologically active additives. Due to its property profile, Kebaform® / C 25 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

PPS-MD60, linear PPS, 60% mineral filled, good surface quality

BARLOG plastics GmbH Kebaform® / C 130 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Due to its property profile, Kebaform® / C 130 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow any compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

Aipol Spa APAN is a thermoplastic polyurethane (TPU) pellet, produced through “reactive extrusion” in the Aipol plant of Montegranaro. The TPUs combine the high technical properties of the polyurethane elastomers, to the possibility of processing through a termoplastic technology. A bridge between rubber and traditional thermoplastics.

PPS-GF40, linear PPS, 40% glass fiber reinforced

linear PPS, 40% glass fiber reinforced, impact resistant

Plain bearing material based on PPS, PPS + carbon fiber + graphite

SINTERLINE® Unfilled are the first polyamide 6 powder range designed for selective laser sintering (SLS). This solution yields the mechanical and thermal performance required to make 3D parts printing a compelling option for prototyping and low to medium volume production.

POM copolymer unreinforced, medium viscosity, tribologically modified, optimized sliding and wear behavior

MB 1200 is an Apricot and/or Pink colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1200 is low density foam of approximately 20lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1200 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

Grupa Azoty S.A Tarnoform® 300 SI is an Acetal (POM) Copolymer material. It is available in Africa & Middle East, Asia Pacific, Europe, Latin America, or North America for injection molding.Important attributes of Tarnoform® 300 SI are: Flame Rated Chemical Resistant Bacteria Resistant Copolymer Fatigue Resistant Typical applications include: Engineering/Industrial Parts Automotive Plumbing/Piping/Potable Water

BARLOG plastics GmbH Kebablend® / WR 01/2202 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material has medium strength and a very high elongation at break.

BARLOG plastics GmbH Kebablend® / WR 01/1125/2110 is a special compound based on POM that combines high strength and rigidity with good sliding behavior and high wear resistance.

MB 1300 is a Mahogany colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1300 is medium low density foam of approximately 30lbs/ft³ board. Easily cut using CNC machining equipment the MB 1300 is perfectly suited for visual master models, architectural design models as well as design verification and prototype tools.

PPS-GF40, linear PPS, 40% glass fiber reinforced, approved for food applications according to EU and FDA guidelines.