Products in Other Automotive Applications: Compression Molding

Cuyahoga Plastics EB5000-1 is A U.L recognized, flame retardant, mineral-filled, glass fiber reinforced polyester thermoset molding compound suitable for compression, transfer, and injection molding. It is currently supplied in bulk form, cut preforms, and box length extrusions.

Cuyahoga Plastics EB7000-1 is A U.L recognized, flame retardant, mineral-filled, glass fiber reinforced polyester thermoset molding compound suitable for compression, transfer, and injection molding. It is currently supplied in bulk form.

Cuyahoga Plastics AB5000 is a UV resistant, flame retardant, glass-reinforced polyester thermoset suitable for outdoor applications. Compression, transfer, and injection molding grades are available. It is currently supplied in bulk form, cut preforms, and box length extrusions.

Cuyahoga Plastics AB4000 is a mineral-filled, glass fiber reinforced polyester thermoset suitable for compression, transfer, and injection molding. It is currently supplied in bulk form, cut preforms & box length extrusions.

Cuyahoga Plastics EB3000-2 is A U.L recognized, flame retardant, mineral-filled, glass fiber reinforced polyester thermoset molding compound suitable for compression, transfer, and injection molding. It is currently supplied in bulk form, cut preforms and box length extrusions.

StarPCS™ SBMC-998 are carbon fiber reinforced molding compounds containing a discontinuous carbon fiber, a specially formulated StarPCSTM polycarbosilane resin, and refractory particulate. SBMC-900 and SBMC-998 can be used in the cured state, but are specifically designed for use as a ceramic matrix composite (CMC) thermal or mechanical structure.

AMC® 8595 (unidrectional) is a unidirectional carbon fiber reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 60K tow.

Resinoid Compound 1322 is a glass reinforced, two step molding compound. It may be preformed. Recommended for transfer, injection or compression molding

PRF Composite Materials RS-L285 has very low mixed viscosity, ensuring a fast and complete impregnation of reinforcement fibers without drainage on vertical surfaces. The addition of fillers such as colloidal silica, microballoons, metal powder etc., is also acceptable to obtain special properties. The RS-L285 epoxy resin system exhibits good mechanical properties after curing at room temperature. If high temperature strength (≥ +60°C) or aircraft approval is not required, finished products made with the selection of hardener RS-H285 may be used without further heat treatment. Post curing (heat treatment) will further enhance the mechanical properties and will also increase the high temperature strength, up to 100°C being achievable depending on the selected hardener and post cure cycle used. The properties indicated in this document may only be achieved by curing/post-curing above 50°C.

AMC® 8590HT is a chopped carbon fiber reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 12K tow.

Mar-Bal MB3000-15NY is a superior chemical-resistant material with excellent flame and track resistance.

AX-5605 is a modified Silica, Carbon Prepreg.

Resinoid 2089 is a chopped fabric reinforced, two-step phenolic molding compound offering good physical and wear properties. This product has been specifically formulated for mechanical applications where minimal wear and low shrinkage values are desired. This material comes in bulk fabric form and is suitable for compression molding.

Resinoid 1371 is a glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for applications requiring prolonged exposure to elevated temperatures andresistance to thermal shocks.This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

G-TEX M 1200 is Nonwoven fabric made from recycled carbon fiber. 1200 denotes the fabric width in mm.

Resinoid 2016P is a fabric reinforced, two-step phenolic molding compound offering excellent resistance to mechanical shock. It is supplied in pellet form suitable for transfer and compression molding. This material can also be used in injection molding systems with deep flight screws

Mar-Bal MB5500 with a UL RTI rating of 160°C-170°C, the 5500 provides a superior heat resistant material for your application.

AMC® 8590 is a chopped carbon fiber reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 12K tow.

Resinoid 1360HR is a glass reinforced, two-step phenolic molding compound. It exhibits outstanding impact strength, electrical and thermal properties. It is particularly suitable for high temperature and strength applications. This material comes in pelletized from and is suitable for transfer or compression molding. It can be preformed on automatic equipment.

Resinoid 2005 is a cellulose reinforced, two-step phenolic molding compound. It exhibits excellent electrical and thermal properties and dimensional stability. This material comes in pelletized from and is suitable for transfer or compression molding. It can be preformed on automatic equipment.

Resinoid 2277 is a chopped fabric reinforced, two-step phenolic molding compound. It was specifically developed for molding applications where a lightweight, high strength material with good impact strength is needed. This material comes in pelletized from and is suitable for transfer or compression molding and can be used in injection molding systems with deep flight screws. Resinoid 2277 meets the requirements of ASTM D-5948 CFI-20 (Formerly MIL M14/1 CFI-20).

Resinoid 1382 is a glass reinforced, two-step phenolic molding compound formulated for applications requiring exceptional tensile strength. It has been used to replace cast aluminum in certain applications. Resinoid 1382 exhibits excellent dimensional stability, electrical and thermal properties. It is supplied in pelletized form for use in injection, transfer, and compression molding. It can be preformed on automatic equipment.

G-TEX M SM45 is Nonwoven fabric made from recycled carbon fiber. SM45 denotes Fiber type; it signifies Standard modulus with strength between 4-5 GPa.

Mar-Bal MB2000-15 is an excellent flame and track resistant material possessing outstanding electrical and mechanical properties.

Resinoid 2002-4A is a fabric reinforced, two-step phenolic molding compound. It has been modified to meet gear requirements and other stressed applications. It possesses excellent impact and flexural strength. It is available in bulk form and is recommended for compression or transfer molding.

G-TEX TM PP/60 is Nonwoven fabric made from recycled carbon fiber and mixed with thermoplastic fibers. PP/60 Denotes type and weight% of thermoplastic; it signifies inclusion of PP fiber at 60wt%.

AMC® 8575 (woven) is a vinyl ester ESC® molding compound reinforced with 12K 2x2 Twill Carbon Fiber Fabric. It is designed for compression molding of components requiring high structural strength, light weight, and stiffness. It can also be comolded with other ESC molding compounds such as AMC® 8590 to provide stiffening in selected areas of the component.

StarPCS™ SBMC-900 are carbon fiber reinforced molding compounds containing a discontinuous carbon fiber, a specially formulated StarPCSTM polycarbosilane resin, and refractory particulate. SBMC-900 and SBMC-998 can be used in the cured state, but are specifically designed for use as a ceramic matrix composite (CMC) thermal or mechanical structure.

AMC® 8593 is a chopped carbon fiber reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 3K tow.

AMC® 8590-12CFH (Hybrid) is a chopped carbon fiber combination E-glass reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 12K tow.

Blu Dot Asia CCF06EP is produced by chopping carbon fiber roving/thread into shorter lengths with different sizes.

G-TEX TM 200 is Nonwoven fabric made from recycled carbon fiber and mixed with thermoplastic fibers. 200 denotes the fabric areal weight in gsm.

Resinoid 1365 is a glass reinforced, two-step phenolic molding compound offering excellent mechanical strength as well as good electrical and thermal characteristics. This material is offered as a moderate size pellet suitable for compression and transfer molding. It can be used in injection molding systems with deep flight screws.

PREGNIT TP-PC is a transparent, dimensionally stable, impact resistant, flame retardant possible according to UL94-VO, printable.

Resinoid 1528 is a glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated for use in automotive applications. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment

PRF Composite Materials RP570 is a high performance formulated epoxy resin system with rapid Tg development enabling extremely short process times and excellent esthetic finish. A press tool held at constant temperature of 140°C can produce a part every 4 minutes ready for painting. RP-570 can be supplied on a variety of woven fabrics.