Products in Bonding & Assembly: Gears

Nylene Recommended for molding applications requiring both maximum durability and toughness Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

BARLOG plastics GmbH Kebaform® / C 25 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Kebaform® / C 25 H improves the sliding and wear behavior solely by modifying the polymer chain and there is no reduction in mechanical properties due to the addition of tribologically active additives. Due to its property profile, Kebaform® / C 25 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

BARLOG plastics GmbH Kebaform® / C 130 H is a new type of POM that was developed specially for sliding and wear applications. Compared to a standard POM copolymer, the material is characterized by a higher crystalline structure and thus better wear properties and a higher melting temperature. Due to its property profile, Kebaform® / C 130 H is particularly well suited for applications that require good sliding and wear behavior, but do not allow any compromises in mechanical properties, e.g. For gears, rollers, plain bearings, guide bushes, etc.

POM copolymer unreinforced, medium viscosity

Nylene Duratel MF3 is a high-viscosity acetal co-polymer. Duratel MF3 has slightly higher toughness than standard MF9, and parts molded with MF3 should have thicker wall sections and shorter flow lengths to accommodate the higher viscosity. MF3 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene Duratel MF27 is an unreinforced high-flow acetal co-polymer. Duratel MF27 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF27 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

Nylene Duratel MF9 is an un-reinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required

Nylene Duratel MF9 is an unreinforced general purpose acetal co-polymer. Duratel MF9 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF9 issuitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

CP-Polymer Technik Wellamid® 22LN2-N is a Polyamide 66 (Nylon 66) material. It is available in Asia Pacific, Europe, Latin America, or North America for injection molding. Primary attribute of Wellamid® 22LN2-N: Flame Rated.Typical application of Wellamid® 22LN2-N: Automotive

BARLOG plastics GmbH Kebaform® / C 901 TS is a specially modified type, which is characterized by excellent sliding and wear properties. Despite the highly efficient modification with PTFE and a special silicone oil, Kebaform® / C 901TS has excellent mechanical properties. Kebaform® / C 901TS is used wherever high demands are placed on wear resistance, uniformity of friction behavior under changing conditions and low noise levels, and at the same time the mechanical property profile of a technical construction material is required. Kebaform® / 901TS is particularly suitable for sliding pairings with changing operating conditions, e.g. B. When starting behavior without stick-slip effect is just as required as high wear resistance over the entire service life.

Engineering Grade Nylon Resin (PA66)

POM copolymer unreinforced, dry blend with color masterbatch green, medium viscosity for injection molding

Nylene Medium viscosity, fast cycle molding resin.Crystallization initiators provide fast molding cycles through rapid melt set-up.Parts molded from NX1440 have better dimensional stability at moisture equilibrium than parts molded from conventional nylon.Suitable for such uses as clips and fasteners, bushings, small levers, gears, and window hardware.Optimum processing conditions should provide a melt temperature of 460 - 480°F at the nozzle.

Nylene Heat stabilized version of NYLENE 451 recommended for molding - Exceptional fatigue and wear resistance insure long product life to gears, bearings, cams, fasteners, and other load bearing parts Chemically resists oil and grease Optimum processing conditions should provide a melt temperature of 460°F-480°F at the nozzle

POM copolymer unreinforced, medium viscosity, UV stabilized

POM copolymer unreinforced, medium viscosity for injection molding

BARLOG plastics GmbH Kebaform® / C FE 161105 is a tribologically optimized POM copolymer which, due to its property profile, is particularly suitable for applications that require good sliding and wear behavior.

POM copolymer unreinforced, medium viscosity, optimized crystallization behavior

POM copolymer unreinforced, medium viscosity, worldwide drinking water approvals