Products in Automotive & Transportation: Polyimides (PI)

C-Stock RH-5 is a series of rigid Polymethacrylimide foams which will withstand temperatures to 380ºF. C-STOCK RH has a high compression and shear strength and a very low dielectric constant and low loss factor. It is easily machined to close tolerances.

HexPly® F652 is a bismaleimide resin that cures via an addition reaction with no condensation by-products. HexPly® F652 is a controlled flow polyimide resin system designed for alternative processing capabilities such as co-curing over honeycomb core, compression molding, as well as standard autoclave processing.

Maverick Corporation MVK-10 is a high‐temperature thermosetting polyimide resin with service capability up to288°C. Its low melt viscosity (300‐600 cP at 260°C) makes MVK‐10 one of a small number ofpolyimides suitable for use in resin transfer molding (RTM) processes. MVK‐10 compositesproduced produced by RTM exhibit exhibit no voids or microcracking microcracking.Originally developed by Maverick to replace PMR‐15 and its highly toxic diamine 4,4’‐methylenedianiline (MDA), MVK‐10 contains no mutagenic or carcinogenic components. Although it is most suited for RTM processing, its chemistry also allows for the use of autoclaveprocessing or compression molding. MVK‐10 is available as a PMR‐type resin solution or as apre‐imidized imidized powder from Maverick Maverick Corporation. Corporation.

Tubus Bauer GmbH PEI 4,0-48C is a tubus core made with Polyetherimide.

Comco PLAVIS ESD is Electrostatically dissipative and has high thermal resistance, superior mechanical properties and surface resistivity 10²-10³. Modification: electrostatic dissipative.

35NQ is a pure polyimide laminate and prepreg system. Reinforced with woven Quartz fabric, combining the advantages of a reduced cure cycle, high temperature polyimide system (Tg >/=250°C), with low dielectric constant and loss tangent (DK = 3.5, loss 0.009 at 1 MHz) for applications requiring operation at RF/Microwave frequencies. Polyimide Quartz materials also exhibit reduced in-plane CTE for expansion matched SMT applications.

Tubus Bauer GmbH PEI 4,0-64C is a tubus core made with Polyetherimide.

Tubus Bauer GmbH PEI 4,0-75C is a tubus core made with Polyetherimide.

Maverick Corporation MVK-19 is an ultra-high temperature polyimide resin with continuous service capability up to 371°C. MVK-19’s excellent thermal stability makes it suitable for use in some of the harshest applications for composite bearings and structures.MVK-19 does not contain the toxic diamine 4,4’-methylenedianiline (MDA) or any other carcinogenic or mutagenic component. Its chemistry makes MVK-19 most suitable to be processed by compression molding.MVK-19 was formulated and developed by Maverick, and it has been qualified for use in military and commercial jet engines since 1994. Maverick Molding Company manufactures MVK-19 molded parts in high-rate production at our Blue Ash facility. MVK-19 is available as a resin solution from Maverick Corporation.

Maverick Corporation MVK-16 is a high-temperature thermosetting polyimide resin with service capability up to 288°C (204°C wet). Originally developed by Maverick to replace PMR-15 and its highly toxic diamine 4,4’-methylenedianiline (MDA), MVK-16 contains no mutagenic or carcinogenic components. Although it is most suited for autoclave processing, its chemistry also allows for the use of compression molding. MVK-16 is available as a PMR-type resin solution from Maverick Corporation, or as a prepreg from Renegade Materials Corporation.

Comco PLAVIS N has best physical properties, maximum electrical and thermal insulation, low outgassing, superior radiation resistance. Modification: non–filled.

Comco PLAVIS C has electrical conductivity, high thermal resistance, superior mechanical properties and surface resistivity 10²-10³. Modification: conductive.

Maverick Corporation J1 is a high‐temperature thermosetting polyimide resin with service capability up to 371°C. Itslow powder melt viscosity (300‐600 cP at 274°C) makes J1 one of a small number of polyimidessuitable suitable for use in resin transfer transfer molding molding (RTM) processes processes.J1 does not contain the toxic diamine 4,4’‐methylenedianiline (MDA) or any other mutagenic orcarcinogenic components. Although it is most suited for RTM processing, its chemistry alsoallows for the use of autoclave processing or compression molding.J1 is available as a PMR‐type resin solution or as a pre‐imidized powder from MaverickCorporation.