Products in Building Materials: High Strength

Resinoid 2277 is a chopped fabric reinforced, two-step phenolic molding compound. It was specifically developed for molding applications where a lightweight, high strength material with good impact strength is needed. This material comes in pelletized from and is suitable for transfer or compression molding and can be used in injection molding systems with deep flight screws. Resinoid 2277 meets the requirements of ASTM D-5948 CFI-20 (Formerly MIL M14/1 CFI-20).

GEHR PSU® is amber-colored, transparent material belongs to the group of amorphous high-performance plastics. Polysulfone has a good heat deflection temperature and heat aging resistance (-100 °C to +160 °C). In addition, this material has a high hardness and strength, very good hydrolytic stability and high radiation resistance (permeable to microwaves up to 2.45 GHz). PSU also has high dimensional stability and resistance to β- and γ-, X-rays and infrared rays. However, PSU is not UV stable and notch sensitive.

From classical man-made fibers to man-made fibers on cellulose base to high performance fibers. Kevlar 220 dtex can be used custom-designed for BAFA®-laid scrims.

GEHR PA® 6.6 is slightly increased surface hardness and rigidity of PA 6.6 is due to the reduced moisture absorption behavior compared to PA 6 XT. Abrasion resistance and heat deflection temperature could also be optimized at the expense of toughness.

BARLOG plastics GmbH Kebablend® / WR XB 111001/1 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

BC 13 136 Basalt yarn is employed for the production of basalt fabrics tapes and cords.

GEHR PA® 6 XT is a PA 6 which shows a very tough behavior and which was produced by extrusion. Our round rods and sheets in natural color comply with the food contact regulations according to 10/2011/EC.

Kayco Composites R25 is a rigid, closed-cell, high-density polyurethane foam core panel. The reinforced panel is a sandwich construction with fiberglass reinforcements. The fiberglass reinforcements are offered in several schedules.

ACM C800P is a Unidirectional Woven Fabrics with Standard fabric width of 300 mm and Custom width range of 120—1600 mm having EP/VE Resin compatibility. Unidirectional carbon tapes are carbon fabric with at least 85% of the filaments arranged in the same direction. Thin glass, aramid, or hot melt fibers are used as weft (cross fibers). This structure supports the high tensile strength of the carbon tape and makes it a relevant material in demand for construction and many other applications.

TYCOR® W7.1 provides designers a cost advantage compared to balsa and structural foam. The fiber-reinforced pre-form core is designed for vacuum infusion. It is comprised of fiberglass webs which develop nearly allthe core’s mechanical properties upon infusing and helps prevent resin race tracking even in contoured shapes. Fine cell foam minimizes excess resin absorption and provides durability during handling and processing. TYCOR® W0.1 engineered core materials optimize weight, stiffness and strength in infused applications enabling structures that can be made lighter, less expesively and more reliably than old generation core materials.

KRAIBURG NR is a natural rubber used in applications such as conveyor belts, flexible couplings, motor bearings, bridge bearings, O-rings, seals and buffers.

AH 110/GL is an epoxy resin with high strength even on elevated temperatures. It can be used as a casting resin with powdery fillers like aluminum powder, as a laminating resin with fiber glass cloth and as a bonding resin for granular fillers like aluminum granules. Depending on the application you can choose from a variety of hardeners. AH 100/GL is suitable as laminating resin for large area parts and thick laminates. Due to its almost odourles skin friendly hardener GL, this mixture is especially applicable as laminating resin. With a mixing ratio of 100:39 you reach an about 15°C higher TG, slightly stiffer laminates as well as better impact resistance. The laminate thickness should not exceed 6-7 mm.

Flax 500 dtex is a natural fiber yarn that grows again, fibers fibers that decompose. Requirements that are easy to please, BAFA®-laid scrims.

AKSACA™ 12K A-42 is a High Quality Carbon Fiber.

Tarnoform® 300 GF6 TF3 is a polyacetal copolymer (pom) polymer lowered wear and friction coefficient modified with 30% glass fibers reinforced.

Thermo-Cor™ FR 2.0 phenolic foam is a rigid, semi-closed celled, foam that comes in a full range of densities from 2.0 pcf to 40.0 pcf.Thermo-Cor FR has a higher compression strength ratio than competing phenolic foams of the same density. Its superior structural strength makes it well suited for stand-alone panels and stress skins used either as thermal or acoustical insulation for commercial applications, especially in hospitals, nursing homes and other public places where low smoke and toxicity are important.

PBY Plastics PB40300R is a compression molded 40% glass fiber filled Poly(p-Phenylene Sulfide) (PPS).

T430 Fulcrum Thermoplastic Composite Tube is produced with a proprietary rigid engineering thermoplastic polyurethane matrix. The combination of ductile thermoplastic matrix with high strength continuous fibers results in excellent strength and stiffness combined with superior toughness. The resin offers excellent resistance to a broad range of chemicals, including acids, bases and organic liquids.

Ebalta SG 131 / PUR 11 is a Polyurethane system. Material should be carefully stirred up/ shaked before use. Filler content and sales units are on the separate mixing table noted.

BARLOG plastics GmbH Kebablend® / WR 01/1220 is a special compound based on POM, which combines high strength with good sliding behavior and high wear resistance, as well as electrical conductivity.

POM-GF10, POM copolymer, medium viscosity, 10% glass fiber reinforced

HTC™ 9593 is a chopped carbon fiber reinforced ESC® molding compound. It is easily moldable and provides parts that are high strength, fatigue resistant, with high heat resistance and a low density. The carbon fiber is standard modulus PAN based 3K tow.

T76 Fulcrum Thermoplastic Composite Tube is produced with a proprietary rigid engineering thermoplastic polyurethane matrix. The combination of ductile thermoplastic matrix with high strength continuous fibers results in excellent strength and stiffness combined with superior toughness. The resin offers excellent resistance to a broad range of chemicals, including acids, bases and organic liquids.

SIMONA® PE 100 black 10024796 Line range of pipes and fittings with FM certification offers a superior standard of safety and quality for use in subterranean fire extinguishing systems. What is more, SIMONA® is the first plastics manufacturer worldwide to supply "FM APPROVED" pipes and fittings in sizes up to d 630 mm. It has High heat stability, UV-stabilized, creep strength at 50 years, 20°C, medium water = 10 Mpa.

POM copolymer unreinforced, medium viscosity, antistatic

THINPREG™ TP 513 is a prepreg resin matrix used for the manufacture of light weight prepreg molding materials. ThinPreg™ 513 is a versatile system that is used most often with carbon fiber, but can also be impregnated into a wide range of reinforcing fibers including quartz, glass, aramid etc.

This reinforcing mat is a continuous-filament product, which is treated with a suitable bonding resin and coupling agent. It has good handling properties, resists wash in the mold, has good porosity, fast wet through, exceptionally good formability, weight uniformity, and uniform strand integrity.

BC16 200 has high natural strength, resistance to corrosive environment, long operation life and perfect electric insulation properties. It is applied in various areas.

KRAIBURG NBR is a nitrile rubber used in applications such as oil- and fuel-resistant seals, membranes, hoses, conveyor belts, rubber-metal bonds, plastic-to-rubber bonded parts and friction linings.

Kiamid 6 S3C-0 NT is a unamplified Polyamide 6.

R46 Fulcrum Thermoplastic Composite Rod is produced with a proprietary rigid engineering thermoplastic polyurethane matrix. The combination of ductile thermoplastic matrix with high strength continuous fibers results in excellent strength and stiffness combined with superior toughness. The resin offers excellent resistance to a broad range of chemicals, including acids, bases and organic liquids.

Superior Huntingdon Composites M8635 is this reinforcing mat is a continuous filament product which is treated with a suitable bonding resin and coupling agent for polyester and vinyl ester resins. It has good handling properties, porosity, and formability, resists wash in the mold, and has weight uniformity. Some variations include faster wet through and better porosity.

POM copolymer unreinforced, highly viscous for injection molding and extrusion processing

Envir® PA66G25HL-BK0101 is a 25% Glass fiber reinforced Nylon 66 molding resin, it is Heat stabilized and hydrolysis resistant. 66G25HL is optimized for strength and processibility while offering low volatiles in extrusion applications. It is provided Black in color.

Fiberglass Epoxy Tubing (CL) Commercial Carbon is constructed of fiber reinforced thermoset epoxy resin, fiberglass epoxy tubing (CL) is a lightweight, high strength, corrosion resistant material that can replace carbon steel, chromed steel, stainless steel, aluminum or brass in a variety of applications. General Purpose Fiberglass Epoxy Tubing.

This is a family of con�nuous filament reinforcing mats designed for pultrusion processes. They are treated with a suitable bonding resin and coupling agent and have good handling proper�es and good weight uniformity.