Products in Packaging & Assembly: Water Resistance

Parylene Type N Dimer is the solid, granular starting material used to produce parylene conformal coating films.

The 4353 Thinner 3 is a moderate speed drying thinner for use with the MG Chemical’s conformal coating products. The thinner promotes good flow properties and suppresses blushing.

NACURE® 155 is a hydrophobic sulfonic acid catalyst based on dinonylnaphthalene disulfonic acid supplied as a 55% concentrate in isobutanol. Its primary use is as a catalyst for promoting the cure of hydroxy, carboxy and amide functional polymers with melamine and urea-formaldehyde crosslinking agents.

Parylene Type F Dimer is the solid, granular starting material used to produce parylene conformal coating films.

The 4354 Thinner 4 is a slower drying thinner for use with the MG Chemical’s urethane and acrylic conformal products. The thinner as excellent solvent strength, making it a good oil and grease remover. It has very low water solubility, so it is unlikely to absorb water and create blush. Its drying speed is slow enough to promote excellent leveling, but it is fast enough to accommodate a reasonable assembly line speed.

Sunspacers™ 04.X are finely divided, optically clear, solid fused amorphous silica micronized powders. This product is specially engineered for paints, liquid and powder coatings, inks, adhesives, and thermoplastics, including UV curable compositions. These micronized powders increase corrosion resistance, reduce shrinkage, improve adhesion, and enhance surface qualities including abrasion, mar and scratch resistance. Sunspacers™ 04.X have a median particle size of approximately 3-4 microns, with a particle size range of 0.5 microns to 13 microns.

NACURE® 1051 is an extremely hydrophobic acid catalyst based on dinonylnaphthalene sulfonic acid supplied at 50% active in 2-Butoxyethanol.

The Sunspheres™ 200 Nm ST- 3 are surface treated*, optically clear, solid fused amorphous microspheres designed for optimum dispersion in coatings, inks, adhesives, and thermoplastics, including UV curable compositions. Cured films show enhanced physical and mechanical properties including increased corrosion resistance, reduced shrinkage, improved adhesion, and enhanced surface qualities such as mar and scratch resistance. This product is particularly useful in improving impact resistance. The average particle size is 200 nanometers and range in size from 50 to 500 nm.

Viplex 525-24 is a general purpose extender where good water resistance is required in Polyurethane and Epoxy systems.

Parylene Type C Dimer is the solid, granular starting material used to produce parylene conformal coating films.

Novacite® 1250 is a premium 325 mesh product. Normally, it is 100% finer than 44µ. This outstanding product has been preferred for over 35 years in thermoset molding compounds. We would not hesitate to recommend 1250 Novacite® for almost any application in the polymer field in its range of fineness.

FluorAcryl 1939 is a bifunctional perfluoropolyether (PFPE) urethane acrylate. FluorAcryl is a surface modifier that improves gloss. It is compatible and miscible with low molecular weight reactive UV-curable diluents and acrylic monomers. Some of the properties of FluorAcryl 1939 include good release agent, good water and oil repellency and good chemical resistance. As a surface modifier this also offers good hardness, substrate-wetting and flow-properties. Recommended dosage is between 0.5–5% w/w. During application and UV light curing, FluorAcryl blooms quickly and effectively on the surface of the coating, imparting low surface energy and non-stick E2C properties. FluorAcryl is made for UV curable coatings use.

UNI-REZ 138 polyamide resin is an alcohol soluble type resin of comparatively low viscosity. It has low odor, high gel and water resistance, together with excellent solvent release and blocking resistance. Its high ester tolerance permits addition of small proportions of nitrocellulose without loss of any of these properties.

Tulco INC PD-200 is for low to moderate thickening, anti-foaming, free flowing, anti-caking and silicone rubber application.

Tulco INC HM-103 Deammoniated is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

Tulco INC PD-300 is for low to moderate thickening, anti-foaming, free flowing, anti-caking and silicone rubber application.

FluorAcryl 3298 is a hydrophobic and oleophobic acrylate that produces hard scratch resistance coatings. This oligomer is compatible with UV/EB curing. FluorAcryl has a high Tg, good water resistance, high impact strength and good solvent resistance.

WÜKONIL® PW is an aqueous dispersion for use in varnish- and paint systems WÜKONIL® PW is an aqueous dispersion for use in varnish- and paint system.WÜKONIL® PW modifies the following properties of paint- and varnish formulations:. Our high quality wax emulsions and dispersions are a necessity for all customers who prefer working with ready-made emulsions or dispersions in contrast to a dry wax. The ease of incorporation is the key benefit of liquid products.

Tulco INC HM-250 is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

UNI-REZ 2940 polyamide resin is a co-solvent type resin which is soluble in alcohols, but typically requires mixtures of aliphatic hydrocarbons and alcohols for gel stability. UNI-REZ 2940 polyamide resin provides fast solvent release and good grease resistance in flexographic / gravure inks for plastic substrates and is especially effective as an overprint lacquer.

WÜKONIL® HB 4000 is a wax-dspersion free of emulsifiers for application as additive in waterborne polymer systems.Properties and advantages are good hydrophobicity Improves early rain-resistance Improves \"antisticking\" Improves workability Reducing of skinning at thick coat systems. Our high quality wax emulsions and dispersions are a necessity for all customers who prefer working with ready-made emulsions or dispersions in contrast to a dry wax. The ease of incorporation is the key benefit of liquid products.

Astrocure® 67 Oligomer is a unique, low profile reactive, cycloaliphatic oligomer, especially tailored for application in ultra-violet/electron beam (UV/EB) radiation cured coating. The product is a flexible version of Astrocure® 78. It is light in color and has excellent adhesion to a wide variety of substrates.

Tulco INC PD-500 is for low to moderate thickening, anti-foaming, free flowing, anti-caking and silicone rubber application.

Tulco INC PD-100 is for low to moderate thickening, anti-foaming, free flowing, anti-caking and silicone rubber application.

Tulco INC HM-153 Deammoniated is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

Tulco INC HM-150 is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

UVP 0401, Pentaerythritol tetracrylate (PETA) is a liquid monomer with fast cure response and low volatility during free radical polymerization. It has a low skin irritancy and high cross density upon curing.

RARPOLYOL AP-2605 XL is a acrylic polyol resin with excellent gloss & gloss retention, excellent color/non yellowing characteristics (Isocyanate currant elective).

Tulco INC HM-253 Deammoniated is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

Astrocure® 88 Oligomer is a low viscosity, low reactivity, flexibilizing oligomer that is designed to be used as a flexibilizing agent. It is light in color and should be used with Astrocure® 78 in the 10-15% by weight levels.

UNI-REZ 2221 polyamide resin is an alcohol soluble type resin for flexographic printing. It has high compatibility with nitrocellulose and low viscosity, allowing for high heat resistance and high color strength.

UNI-REZ 2930 polyamide resin is a co-solvent type resin which is soluble in alcohols, but typically requires mixtures of aliphatic hydrocarbons and alcohols for gel stability. UNI-REZ 2930 polyamide resin provides fast solvent release and good grease resistance in flexographic / gravure inks for plastic substrates and is especially effective as an overprint lacquer.

Tulco INC HM-140 is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

Tulco INC PD-400FG is for low to moderate thickening, anti-foaming, free flowing, anti-caking and silicone rubber application.

Tulco INC HM-100 is for low to moderate thickening, free flowing, anti-caking and silicone rubber application.

UNI-REZ 2720 hot melt polyamide adhesive is a resin based on dimer acid. UNI-REZ 2720 hot melt polyamide adhesive offers good chemical resistance, low softening point and low viscosity which allows for a lower application temperature and fast set.