Products in Parts & Components: Prepreg

APCM SG 4528-029CU-102V is a medium weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Resinoid 1345 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for molded electric motor commutators where performance for prolonged periods at elevated temperatures while under centrifugal loads is critical.This material comes in pelletized from and is suitable for injection, transfer or compression molding.

Aeroglide® is an epoxy-based composite surfacing film which can be oven or autoclave cured at either 250°F/120°C or 350°F/180°C to eliminate surface porosity for composite parts.

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.

Resinoid 1328 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for applications requiring exceptional tensile strength such as grinding wheels. Resinoid 1328 exhibits excellent electrical and thermal properties as well as dimensional stability. This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Natex P-Preg PA11 UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polyamide 11 with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

Resinoid 1550 is a milled glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated at a 2.47 specific gravity. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

APCM SG 4528-028AL-105V is a medium weight, conductive, surfacing film composed of a non-woven metallic aluminum mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

APCM DA 4092 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

85N is the ultimate polyimide and laminate prepreg system fo PWB's requiring resistance to high temperature, both in process and in end-use applications. Bromine-free chemistry provides Bestin-Class thermal stability for applications with sustained high in-use temperatures as well as for use in lead-free soldering applications.

APCM DA 4082 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

Natex P-Preg PP UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

Resinoid 1365 is a glass reinforced, two-step phenolic molding compound offering excellent mechanical strength as well as good electrical and thermal characteristics. This material is offered as a moderate size pellet suitable for compression and transfer molding. It can be used in injection molding systems with deep flight screws.

Resinoid 1528 is a glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated for use in automotive applications. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment

Renegade Materials Corporation RM-5003 is a low dielectric and loss with high performance prepreg.

38N is an improved polyimide low-flow prepreg suitable for bonding multilayer polyimide rigid-flex, attaching heat sinks to polyimide MLBs, or other applications where minimal and uniform resin flow is required.

APCM DA 4080 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

Resinoid 1371 is a glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for applications requiring prolonged exposure to elevated temperatures andresistance to thermal shocks.This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Isola’s IS410 has a glass transition temperature (Tg) of 180°C and is specially formulated for superior performance through multiple thermal excursions, passing 6X solder tests at 288°C. IS410 is optimized for enhanced drilling performance allowing high aspect ratio holes of ≤10 mils. Its unique resin chemistry provides CAF resistance with the benefit of long-term reliability of boards built with small feature designs.

G200 has Blending Bismaleimide/Triazine (BT) and epoxy resin which provides G200 with enhanced thermal, mechanical and electrical performance over most epoxy materials. G200 possesses performance characteristics that make it an excellent selection for large panel size, high layer count Printed Wiring Boards (PWB).

Resinoid Compound 1322 is a glass reinforced, two step molding compound. It may be preformed. Recommended for transfer, injection or compression molding

Arlon 85HP’s unique blend of pure polyimide resin and micro-fi ne proprietary fi llers results in superior performance for demanding applications. Compared to conventional polyimide systems, 85HP has a lower Z-axis expansion and twice the thermal conductivity. 85HP reduces resin cracking and wicking in designs with high density plated through holes and vias. 85HP prepreg has resin fl ow characteristics and pressed thickness matching standard polyimides.

Renegade Materials Corporation RM-2014-LDK-TK is a 300°F (150°C) cure, modified epoxy prepreg system with very low dielectric and loss properties. RM-2014-LDk-TK provides good tack, drape and handling, and a great balance of mechanical properties.

33N is a flame retardant (UL94 V-O) polyimide laminate and prepreg system where the excellent high performance properties of polyimide need to be combined with flame retardance. High Tg (250°C) results in low overall z-axis expansion, and minimizes risk of latent PTH defects in-service.

Natex P-Preg PP P1/1 900 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

APCM SG 4528-015CU-101V is a lightweight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

IS420 laminate and prepreg products are manufactured with a unique high performance multifunctional epoxy resin, reinforced with electrical grade (E-glass) glass fabric. This system provides improved thermal performance and low expansion rates in comparison to traditional FR-4 while retaining FR-4 processability. In addition to this superior thermal performance, the mechanical, chemical and moisture resistance properties all equal or exceed the performance of traditional FR-4 materials. The IS420 system is also laser fluorescing and UV blocking for maximum compatibility with Automated Optical Inspection (AOI) systems, optical positioning systems and photo imageable solder mask imaging.

Natex P-Preg PLA P1/1 950 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

TerraGreen® is engineered for such high-performance applications as power amplifier boards for LTE base stations, internet infrastructure and cloud computing. TerraGreen ® features a Dielectric Constant (Dk) that is stable between -55°C and 125°C, up to 20 GHz. TerraGreen® is a lead-free assembly material and is easy to process. This high-performance material utilizes a short-lamination cycle; the product is easy to drill, does not require plasma desmear, and the prepreg shelf life is similar to FR-4 materials. TerraGreen® is suitable for high-layer count, high-speed digital backplanes and is compatible with Isola’s FR-4 materials for hybrid designs. TerraGreen® meets UL 94 V-0 and is halogen free.

I-Speed® laminate and prepreg products are manufactured with Isolas' patentable high performance multi-functional resin system, reinforced with electrical grade (E-glass) glass fabric. This system delivers a 15% improvement in Z-axis expansion and offers 25% more electrical bandwidth (lower loss) than competitive products in this space. These properties coupled with superior moisture resistance at reflow, result in a product that bridges the gap from both a thermal and electrical perspective. The I-Speed® resin system is laser fluorescing and UV blocking for maximum compatibility with Automated Optical Inspection (AOI) systems, optical positioning systems and photo imageable solder mask imaging.

APCM SG 4528-040CU-103V is a heavy weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

APCM DA 4518 E-Glass is a modified epoxy system coated on heavy weight unidirectional E-Glass fibers. This product is designed to build excellent unidirectional strength using a minimum number of plies. DA 4518/E-Glass Uni also features extended room temperature out time and service temperatures to 300°F.

Natex P-Preg PLA UD 800 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

APCM DA 4518 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 250°F (121°C) for one hour and or a cure of 350º F (177ºC) for 1 hour. This material needs to be post cure or cured to 350ºF to get the 350º properties.