Products in Housings & Enclosures: Prepreg

Resinoid Compound 1322 is a glass reinforced, two step molding compound. It may be preformed. Recommended for transfer, injection or compression molding

Resinoid 1328 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for applications requiring exceptional tensile strength such as grinding wheels. Resinoid 1328 exhibits excellent electrical and thermal properties as well as dimensional stability. This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Resinoid 1528 is a glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated for use in automotive applications. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.

Natex P-Preg PA11 UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polyamide 11 with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

APCM SG 4528-028AL-105V is a medium weight, conductive, surfacing film composed of a non-woven metallic aluminum mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

APCM SG 4528-029CU-102V is a medium weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Resinoid 1345 is a glass reinforced, two-step phenolic molding compound. It was specifically developed for molded electric motor commutators where performance for prolonged periods at elevated temperatures while under centrifugal loads is critical.This material comes in pelletized from and is suitable for injection, transfer or compression molding.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

APCM DA 4092 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

Natex P-Preg PP UD 750 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

Resinoid 1550 is a milled glass and mineral reinforced, two-step phenolic molding compound offering good mechanical properties. This product has been specifically formulated at a 2.47 specific gravity. This material comes in pelletized form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

Resinoid 1365 is a glass reinforced, two-step phenolic molding compound offering excellent mechanical strength as well as good electrical and thermal characteristics. This material is offered as a moderate size pellet suitable for compression and transfer molding. It can be used in injection molding systems with deep flight screws.

APCM DA 4082 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

APCM SG 4528-040CU-103V is a heavy weight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

APCM DA 4080 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

Resinoid 1360HR is a glass reinforced, two-step phenolic molding compound. It exhibits outstanding impact strength, electrical and thermal properties. It is particularly suitable for high temperature and strength applications. This material comes in pelletized from and is suitable for transfer or compression molding. It can be preformed on automatic equipment.

Natex P-Preg PLA UD 800 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 750 g/m2.

APCM DA 4518 E-Glass is a modified epoxy system coated on heavy weight unidirectional E-Glass fibers. This product is designed to build excellent unidirectional strength using a minimum number of plies. DA 4518/E-Glass Uni also features extended room temperature out time and service temperatures to 300°F.

APCM SG 4528-015CU-101V is a lightweight, conductive, surfacing film composed of a non-woven metallic copper mesh impregnated with a toughened epoxy resin plus an ultra lightweight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Natex P-Preg PP P1/1 900 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polypropylene with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

Natex P-Preg PLA P1/1 950 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, PolyLactic Acid with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

Resinoid 1371 is a glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for applications requiring prolonged exposure to elevated temperatures andresistance to thermal shocks.This material comes in pelletized from and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

38N is an improved polyimide low-flow prepreg suitable for bonding multilayer polyimide rigid-flex, attaching heat sinks to polyimide MLBs, or other applications where minimal and uniform resin flow is required.

APCM DA 4518 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 250°F (121°C) for one hour and or a cure of 350º F (177ºC) for 1 hour. This material needs to be post cure or cured to 350ºF to get the 350º properties.

Natex P-Preg PA11 P1/1 900 is a powder-coated fabric woven from flax fibers that are pre-impregnated with thermoplastic resins. It comes as NATTEX® P-Preg, Polyamide 11 with 1000 mm Width and pre-preg fabrics uni-directional in natural fibers with flax of 900 g/m2.

APCM SG 4528-016AL-104V is a lightweight, conductive, surfacing film composed of a non-woven metallic aluminum mesh impregnated with a toughened epoxy resin plus an ultra light weight veil for outstanding surfacing capability. It is designed for lightning and shielding protection of aircraft, equipotential ground planes and as a counterpoise for antenna installations.

Resinoid 1382 is a glass reinforced, two-step phenolic molding compound formulated for applications requiring exceptional tensile strength. It has been used to replace cast aluminum in certain applications. Resinoid 1382 exhibits excellent dimensional stability, electrical and thermal properties. It is supplied in pelletized form for use in injection, transfer, and compression molding. It can be preformed on automatic equipment.

APCM DA 409U/G35-150 is a tough, versatile, modified epoxy resin prepreg that cures at 250°F, a standard modulus 150 g/m2 carbon prepreg tape which can also be supplied as a 200g/m2 or a 300 g/m2 prepreg.

Resinoid 1505 is a milled glass reinforced, two-step phenolic molding compound offering good mechanical and electrical properties. This product has been specifically formulated for electrical applications where very low post-molded shrinkage is desired. This material comes in granular form and is suitable for injection, transfer or compression molding. It can be preformed on automatic equipment.