Products in Wire & Cable: Polyurethanes (PU)

85 Products found in Wire & Cable

Browse Applications

Ebalta Kunststoff Gmbh MG 453 GFComp. A + B banner

Ebalta Kunststoff GmbhEbalta Kunststoff Gmbh MG 453 GFComp. A + B

Polymer Name:Polyurethane (unspecified)
End Uses:Automotive Components, Electronic Data Processing, Modeling Material, Automotive Interior Parts, Automotive Exterior Parts
Density:1180.0 - 1220.0 kg/m³

Ebalta MG 453 GF is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Release agent – please see category release agent

Lingen Plastic Rubber FT690 banner

Lingen Plastic RubberLingen Plastic Rubber FT690

Applications:Other Building Materials, Appliances & Electronics, Other Wire & Cable Applications
Product Families:Thermoplastic Urethanes (TPU), Thermoplastic Elastomers
Chemical Family:Thermoplastic Polyurethanes (TPU), Polyurethanes (PU)
Polymer Name:Thermoplastic Polyurethane (Polyether based)
End Uses:Wires, Cables, Appliance Components

Lingen Plastic Rubber FT690 is a Halogen free flame retardant TPU ether.

Miracll Chemicals E 80 banner

Miracll ChemicalsMiracll Chemicals E 80

Polymer Name:Thermoplastic Polyurethane (unspecified)
Processing Methods:Compounding
End Uses:Fuel Pipes, Automotive Components, Bellows, Seats, Hoses, Cables, Wires, Gaskets, Tubes

Miracll Chemicals E 80 is a polyester-based thermoplastic polyurethane used for wide variety of applications.

TEXALAN® 385A banner

Austin Novel MaterialsTEXALAN® 385A

Polymer Name:Polyurethane (unspecified)
Processing Methods:Extrusion, Injection Molding
End Uses:Cables, Pipes, Film, Flexible Packaging, Belts & Belt Repair, Automotive Applications, Automotive Exterior Parts
Density:1180.0 - 1220.0 kg/m³
Tensile Strength:35.0 - 35.0 MPa

Texalan® 385A This product has excellent wear resistance, oil/solvent resistance, low temperature flex resistance, high pressure resistance, Flexibility.

Kebaflex® / U A 63 ST B01 Natural banner

BARLOG plastics GmbHKebaflex® / U A 63 ST B01 Natural

Density:1170.0 - 1170.0 kg/m³
Strain at Break:1000.0 - 1000.0 %

BARLOG plastics GmbH Kebaflex® / U A 63 ST B01 Natural is a TPU with a Shore hardness of A 63. It is characterized by high flexibility and very good wear and abrasion resistance.

RE-FLEX® 790AJL banner

Townsend ChemicalsRE-FLEX® 790AJL

Density:1220.0 - 1220.0 kg/m³
Strain at Break:585.0 - 585.0 %

RE-FLEX® 790AJL is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

TEXALAN® 382A banner

Austin Novel MaterialsTEXALAN® 382A

Polymer Name:Polyurethane (unspecified)
Processing Methods:Extrusion, Injection Molding
End Uses:Cables, Pipes, Film, Flexible Packaging, Belts & Belt Repair, Automotive Applications, Automotive Exterior Parts
Density:1190.0 - 1230.0 kg/m³
Tensile Strength:30.0 - 30.0 MPa

Texalan® 382A This product has excellent wear resistance, oil/solvent resistance, low temperature flexural resistance, high pressure resistance, and Flexibility.

RE-FLEX® 570A banner

Townsend ChemicalsRE-FLEX® 570A

Density:1080.0 - 1080.0 kg/m³
Strain at Break:855.0 - 855.0 %

RE-FLEX® 570A is highly versatile and can be easily processed by injection molding, extrusion, blow molding, vacuum forming, solution coating and compounding. Parts made from RE-FLEX can be welded, sterilized, printed, painted, laser marked, colored, machined and die-cut.

ISOTHANE 1090A banner

Great Eastern ChemicalISOTHANE 1090A

Strain at Break:560.0 - 560.0 %

ISOTHANE 1090A are poly(adipate)ester based thermoplastic polyurethanes, thermoforming TPU. They exhibit excellent toughness, abrasive resistance, and solvent resistance. These products can be injection molded, blow molded, and extruded.

TEXALAN® 282A banner

Austin Novel MaterialsTEXALAN® 282A

Polymer Name:Polyurethane (unspecified)
Processing Methods:Extrusion, Injection Molding
End Uses:Cables, Pipes, Film, Flexible Packaging, Belts & Belt Repair, Automotive Applications, Automotive Exterior Parts
Density:1170.0 - 1210.0 kg/m³
Tensile Strength:32.0 - 32.0 MPa

TEXALAN® 282A This product is safe and environmentally friendly, has excellent abrasion resistance, solvent resistance, good hand feeling, repeated benefits High utilization rate, high strength and excellent processing performance.

BCC Resins™ DP-11-83 banner

BCC ProductsBCC Resins™ DP-11-83

Polymer Name:Polyurethane (unspecified)
Processing Methods:Casting
End Uses:Cable Jacketing

DP-11-83 is a low viscosity, quick setting, easy to use adhesive and/or casting material. This product was designed to bond together the MB1200 foam board to create desired dimensions in length, width and height. DP-11-83 has a working life of up to 13 minutes for casting applications. If used as an adhesive, it is workable for up to 16 minutes.

Ebalta Kunststoff Gmbh MG 453Comp. A+B banner

Ebalta Kunststoff GmbhEbalta Kunststoff Gmbh MG 453Comp. A+B

Polymer Name:Polyurethane (unspecified)
Processing Methods:Injection Molding, Casting, Reaction Injection Molding (RIM)
End Uses:Automotive Components, Modeling Material, Automotive Interior Parts, Electronic Data Processing, Automotive Exterior Parts
Density:1170.0 - 1210.0 kg/m³

ebalta MG 453 is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Release agent – please see category release agent

Ebalta Kunststoff Gmbh MG 426Comp. A + B banner

Ebalta Kunststoff GmbhEbalta Kunststoff Gmbh MG 426Comp. A + B

Polymer Name:Polyurethane (unspecified)
Processing Methods:Casting
End Uses:Automotive Components, Modeling Material, Automotive Interior Parts, Electronic Data Processing, Automotive Exterior Parts
Density:1150.0 - 1190.0 kg/m³
Tensile Strength:48.0 - 58.0 MPa

ebalta MG 426 is processed on a two-component low pressure device. After grinding with a sand paper , grit 280, the surface can be varnished with a commercial lacquer. For better adhesion we recommend the use of a primer coat. Nitrocellulose lacquers have a better adhesion on polyurethane surfaces than on acryl-lacquer- systems. Release agent – please see category release agent.

Show

of 85 results