Products in Medical Devices & Assemblies: Styrenic Thermoplastic Ela...

41 Products found in Medical Devices & Assemblies

Kebaflex® - H / SABS 70 A.03 Black banner

BARLOG plastics GmbHKebaflex® - H / SABS 70 A.03 Black

Strain at Break:618.0 - 618.0 %
Compression Set (70 °C):64.0 - 64.0 %

TPE-S, Shore A69, black, modified for good adhesion to ABS, PC and ABS / PC blends.

Kebaflex® - H / SPAS 50 A.01 banner

BARLOG plastics GmbHKebaflex® - H / SPAS 50 A.01

Strain at Break:240.0 - 240.0 %

TPE-S, Shore A54, modified for good adhesion to polyamides such as PA6, PA66, PA12 or partially aromatic PA types such as e. g. GRIVORY GV (manufacturer EMS-GRIVORY)

Kebaflex® - H / SPA1 40 A.02 Black banner

BARLOG plastics GmbHKebaflex® - H / SPA1 40 A.02 Black

Strain at Break:545.0 - 545.0 %

TPE-S, Shore A45, modified for good adhesion to polyamides such as PA6, PA66, PA612 or partially aromatic PA types such as GRIVORY GV (manufacturer EMS-GRIVORY). KEBAFLEX - H / SPA1 40 A.02 black is UV-resistant and therefore also suitable for outdoor applications, for example in the automotive sector.

Resiprene® 1030 banner

ResireneResiprene® 1030

Strain at Break:1500.0 - 1500.0 %

RESIPRENE® 1030 is a Thermoplastic Elastomer (TPE) easy to process and great for injection molding process

Kebaflex® - H / SPC 55 A.04.1 Black banner

BARLOG plastics GmbHKebaflex® - H / SPC 55 A.04.1 Black

Strain at Break:564.0 - 564.0 %
Compression Set (70 °C):70.0 - 70.0 %

TPE-S, Shore A55, black, modified for good adhesion, etc. On ABS, PC and PC / ABS blends.

Kebaflex® - H / SABS 75 A.01 Black banner

BARLOG plastics GmbHKebaflex® - H / SABS 75 A.01 Black

Strain at Break:550.0 - 550.0 %
Compression Set (70 °C):62.0 - 62.0 %

TPE-S, Shore A76, black, modified for good adhesion to ABS, PC and ABS / PC blends. Also suitable for automotive interior applications.

Kebablend® / RS 170701/1 banner

BARLOG plastics GmbHKebablend® / RS 170701/1

Strain at Break:130.0 - 130.0 %

BARLOG plastics GmbH Kebablend® / RS are special compounds based on different polymers for applications by which radiation is to be shielded. Kebablend® / RS 170701/1 was developed for applications that are intended to shield soft and hard X-rays.

Kebaflex® - H / SPA2 80 A.01 Natural banner

BARLOG plastics GmbHKebaflex® - H / SPA2 80 A.01 Natural

Strain at Break:670.0 - 670.0 %

TPE-S, Shore A80, natural, modified for good adhesion to various polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as e.g. GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY)

Kebaflex® - H / SPA1 80 A.01 banner

BARLOG plastics GmbHKebaflex® - H / SPA1 80 A.01

Strain at Break:350.0 - 350.0 %
Compression Set (70 °C):70.0 - 70.0 %

TPE-S, Shore A80, modified for good adhesion to polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY).

Kebaflex® - H / SPAS 35 A.01 banner

BARLOG plastics GmbHKebaflex® - H / SPAS 35 A.01

Strain at Break:350.0 - 350.0 %

TPE-S, Shore A35, modified for good adhesion to polyamides such as PA6, PA66, PA12 or partially aromatic PA types such as e. g. GRIVORY GV (manufacturer EMS-GRIVORY)

Kebaflex® - H / SPA3 80 A.01 Black banner

BARLOG plastics GmbHKebaflex® - H / SPA3 80 A.01 Black

Strain at Break:420.0 - 420.0 %

TPE-S, Shore A80, modified for good adhesion to polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY).

Resiprene® 1075 170P banner

ResireneResiprene® 1075 170P

Strain at Break:1100.0 - 1100.0 %

RESIPRENE® 1075 170P is a Thermoplastic Elastomer (TPE) easy to process and great for injection molding process

Kebaflex® - H / SPA1 70 A.03/1 banner

BARLOG plastics GmbHKebaflex® - H / SPA1 70 A.03/1

Strain at Break:420.0 - 420.0 %

TPE-S, Shore A68, modified for good adhesion to polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY).

Kebaflex® - H / SPA3 60 A.02 Natural banner

BARLOG plastics GmbHKebaflex® - H / SPA3 60 A.02 Natural

Strain at Break:565.0 - 565.0 %

TPE-S, Shore A64, modified for very good adhesion to polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as e.g. GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY).

Kebaflex® - H / SPC 45 A.04 Black banner

BARLOG plastics GmbHKebaflex® - H / SPC 45 A.04 Black

Strain at Break:600.0 - 600.0 %

TPE-S, Shore A50, black, modified for good adhesion, etc. On ABS, PC and PC / ABS blends.

Kebaflex® - H / SPA2 60 A.04 Black banner

BARLOG plastics GmbHKebaflex® - H / SPA2 60 A.04 Black

Strain at Break:460.0 - 460.0 %
Compression Set (70 °C):40.0 - 40.0 %

TPE-S, Shore A60, modified for good adhesion to polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as e.g. GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY)

Kebaflex® - H / FE 190705 banner

BARLOG plastics GmbHKebaflex® - H / FE 190705

Strain at Break:600.0 - 600.0 %

TPE-S, Shore A75, modified for good adhesion, etc. On PBT and PBT blends.

Kebaflex® - H / SPC 45 A.03.1 Black banner

BARLOG plastics GmbHKebaflex® - H / SPC 45 A.03.1 Black

Strain at Break:510.0 - 510.0 %

TPE-S, Shore A45, black, modified for good adhesion, etc. On ABS, PC and PC / ABS blends.

Resiprene® 1045 banner

ResireneResiprene® 1045

Strain at Break:1400.0 - 1400.0 %

RESIPRENE® 1045 is a Thermoplastic Elastomer (TPE) easy to process □ Easy color match and great for injection molding process

Kebaflex® / SG 85 HT A.01 banner

BARLOG plastics GmbHKebaflex® / SG 85 HT A.01

Strain at Break:480.0 - 480.0 %
Compression Set (70 °C):46.0 - 46.0 %

BARLOG plastics GmbH Kebaflex® / SG 85 HT A.01 is a TPE-S, Shore A85, with improved compression set at high temperatures. It is available in various Shore hardnesses from below A10 to more than D50 and is often used as a substitute for rubber due to the cost-effective processing in the injection molding process. It is soft and flexible, can be colored freely, shows good elastic behavior up to 100°C and is pleasant to the touch. A wide range of modified compounds is available, e.g. adhesion-modified types for 2K injection molding, printable types, variants with optimized compression set, etc.

Resiprene® 1090 banner

ResireneResiprene® 1090

Strain at Break:637.0 - 637.0 %

RESIPRENE® 1090 is a Thermoplastic Elastomer (TPE) easy to process and great for injection molding process

Kebaflex® - H / SPC 60 A.01.1 banner

BARLOG plastics GmbHKebaflex® - H / SPC 60 A.01.1

Strain at Break:635.0 - 635.0 %

TPE-S, Shore A60, natural, modified for good adhesion to ABS, PC and ABS / PC blends

Kebaflex® - H / SPAS 55 A.02 banner

BARLOG plastics GmbHKebaflex® - H / SPAS 55 A.02

Strain at Break:400.0 - 400.0 %

TPE-S, Shore A55, modified for good adhesion to adhesion-modified polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as e.g. GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY)

Resiprene® 1060 banner

ResireneResiprene® 1060

Strain at Break:1088.0 - 1088.0 %

RESIPRENE® 1060 is a Thermoplastic Elastomer (TPE) easy to process and great for injection molding process

Resiprene® 1055 banner

ResireneResiprene® 1055

Strain at Break:1500.0 - 1500.0 %

RESIPRENE® 1055 is a Thermoplastic Elastomer (TPE) easy to process □ Easy color match and great for injection molding process

Kebaflex® - H / SPMMA 75 A.01.1 Black banner

BARLOG plastics GmbHKebaflex® - H / SPMMA 75 A.01.1 Black

Strain at Break:450.0 - 450.0 %
Compression Set (70 °C):62.0 - 62.0 %

TPE-S, Shore A75, black, modified for good adhesion, etc. ABS and PMMA.

Kebaflex® / S FE 160705 banner

BARLOG plastics GmbHKebaflex® / S FE 160705

Strain at Break:800.0 - 800.0 %
Compression Set (70 °C):34.0 - 34.0 %

TPE-S, Shore A65, translucent. Abrasion resistant, high dynamic resilience, good DVR and good adhesion to PP in 2K injection molding.

Kebaflex® - H / SPC 55 A.01 Natural banner

BARLOG plastics GmbHKebaflex® - H / SPC 55 A.01 Natural

Strain at Break:622.0 - 622.0 %

TPE-S, Shore A67, natural, modified for good adhesion, etc. On ABS, PC and PC / ABS blends, compliant for food contact according to EU 10/2011.

Kebaflex® - H / SPC 55 A.05.1 Black banner

BARLOG plastics GmbHKebaflex® - H / SPC 55 A.05.1 Black

Strain at Break:540.0 - 540.0 %
Compression Set (70 °C):70.0 - 70.0 %

TPE-S, Shore A55, black, modified for good adhesion, etc. On ABS, PC and PC / ABS blends.

Kebaflex® - H / SPC 45 A.04 Natural banner

BARLOG plastics GmbHKebaflex® - H / SPC 45 A.04 Natural

Strain at Break:700.0 - 700.0 %
Compression Set (70 °C):67.0 - 67.0 %

TPE-S, Shore A45, modified for good adhesion, etc. On PBT, PC and PC / ABS blends.

Kebaflex® - H / SPA2 55 A.01 banner

BARLOG plastics GmbHKebaflex® - H / SPA2 55 A.01

Strain at Break:530.0 - 530.0 %
Compression Set (70 °C):34.0 - 34.0 %

TPE-S, Shore A55, natural, modified for good adhesion to polyamides such as PA6, PA66, PA6.12 or partially aromatic PA types such as e.g. GRIVORY GV or GRIVORY HT (manufacturer EMS-GRIVORY)

Kebaflex® / FE 170403 banner

BARLOG plastics GmbHKebaflex® / FE 170403

Tear Strength:16.0 - 16.0 kN/m
Strain at Break:430.0 - 430.0 %

BARLOG plastics GmbH Kebaflex® / FE 170403 is a TPE-S, Shore A85, modified for good adhesion to various polyamides such as PA6, PA66, PA6.12, etc. It is available in various Shore hardnesses from below A10 to more than D50 and is often used as a substitute for rubber due to the cost-effective processing in the injection molding process. It is soft and flexible, can be colored freely, shows good elastic behavior up to 100°C and is pleasant to the touch. A wide range of modified compounds is available, e.g. adhesion-modified types for 2K injection molding, printable types, variants with optimized compression set, etc.

Kebaflex® - H / SPBT 70 A.02 Natural banner

BARLOG plastics GmbHKebaflex® - H / SPBT 70 A.02 Natural

Strain at Break:400.0 - 400.0 %
Compression Set (70 °C):62.0 - 62.0 %

TPE-S, Shore A79, natural, modified for good adhesion, etc. On PBT and PBT blends. KEBAFLEX - H / SPBT 70 A.02 natural was developed specially for use outdoors (UV stabilization) and has an optimized demolding behavior.

Kebaflex® - H / SPC 75 A.01.1 Black banner

BARLOG plastics GmbHKebaflex® - H / SPC 75 A.01.1 Black

Strain at Break:450.0 - 450.0 %
Compression Set (70 °C):62.0 - 62.0 %

TPE-S, Shore A75, modified for good adhesion to polycarbonate

Resiprene® 1065 banner

ResireneResiprene® 1065

Strain at Break:1260.0 - 1260.0 %

Resiprene® 1065 is a Thermoplastic Elastomer (TPE) easy to process and great for injection molding process.

Kebaflex® - H / SPA 60 A.02 banner

BARLOG plastics GmbHKebaflex® - H / SPA 60 A.02

Strain at Break:350.0 - 350.0 %

TPE-S, Shore A60, modified for good adhesion to various polyamides such as PA6, PA66, PA6.12

Show

of 41 results