Products in Chemical & Industrial Manufacturing: Gears

Acetal-C + PTFE is a high-quality engineering plastic material.

MEYTEL E6 is a polyamide 6 with a normal viscosity, is nucleated and lubricated. It is suitable for general purpose.

Ketoprix™ EKT33G2L and EKT33G3L resins are thermoplastic aliphatic polyketone compounds where the polyketone base polymer consists of perfectly alternating α-olefins and CO to give the 1,4-diketone polymer backbone structure. To this base resin, fiber reinforcement, additional thermal stabilizers and lubricants are added to achieve desired mechanical performance and to assist in injection molding.

PAR Group Nylon 6 MoS2 Extruded Sheet offers increased load bearing and wear resistance, whilst maintaining the impact and fatigue resistance of standard nylon grades. It is self-lubricating, electrically insulating and has a high fatigue resistance. We also manufacture our own brand of Corromide® CMF (Nylon 6 Sheet - MoS2 Filled Cast) in sheets, rods and tubes. Our MoS2 Filled Cast Nylon 6 is available in greater sheet thicknesses and offers a higher temperature rating compared to MoS2 Filled Extruded Nylon 6. Nylon 6 Sheet - MoS2 Filled Extruded is available to buy online at PAR Direct by clicking the link above.

POM copolymer unreinforced, medium viscosity

Nylene Duratel MF27 is an unreinforced high-flow acetal co-polymer. Duratel MF27 has the high creep resistance, wear resistance, and outstanding chemical resistance inherent in acetal resins. MF27 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

PA 6 reinforced with glass fiber, flame retarded

PA 6/66 reinforced with glass fiber

Extruded polyamide 6 with good strength, impact resistance and good damping properties behave. Due to the manufacturing process, PA 6 has a higher moisture absorption. Compared to cast polyamide, however, it is less dimensionally stable & wear-resistant.

Polimersan Plastics Polipom (POM) is one of the most preferred Polymer due to resistance to bending and wearing,.

Titacon® ST220 is a EXTRUSION GRADE, PERMANENT ANTI-STATIC, NON-SLOUGHING, WEAR RESISTANCE, COLORABLE.

POM-GF27, POM copolymer, medium viscosity, 27% glass fiber reinforced

KEBABLEND / WR 01/2110 is a special compound based on POM, which has very good sliding behavior and high wear resistance.

BARLOG plastics GmbH Kebablend® / WR 07/1130/2115 is a tribologically modified special compound based on PPS that combines high strength with good sliding behavior and high wear resistance, even at elevated temperatures.

Polyamide produced in the extrusion process with high hardness, rigidity and wear resistance but lower impact strength. The properties of PA66 are comparable to those of PA6 G. the However, the material absorbs and is more moisture less true to size.

GEHR PEEK® 30CF is a variant of PEEK modified with 30 % carbon fibers. As with the glass-fiber reinforced type, the surface hardness and heat deflection temperature are also significantly increased compared to the already high values of the unreinforced standard type. This material owes its significantly increased dimensional stability to its extremely low coefficient of linear expansion. The electrical properties are influenced by the high proportion of carbon fibers and must be taken into account in the relevant applications.

Toray Amilan® CM1023G1000 is a Polyamide 6 (Nylon 6) product. It is available in Asia Pacific, Europe, or North America. Characteristics includes flame rated and wear resistant.

ESD E2115 belongs to ESD Polyoxymethylene (Acetal) Series with Anti-static, High mechanical strength, Static dissipative and Good toughness.

POM copolymer unreinforced, medium viscosity, UV stabilized

PA 66 reinforced with glass fiber, heat stabilized

BARLOG plastics GmbH Kebaflex® / U FE 181105/2 Natural is a TPU with a Shore hardness of A 70. It is characterized by high flexibility, very good wear and abrasion resistance as well as good damping and resilience behavior.

Titacon® GF925UV is a 25％GLASS FIBER REINFORCED, HIGH STRENGTH/STIFFNESS, WEATHER RESISTANCE.

TUFFALLOY 4270 is a series of Liquid Molding Compounds with thermoplastic properties such as high impact, high heat distortion, and low viscosity. This unique chemistry developed by Hapco to meet today's market demands for prototype and low production parts needs.THE TUFFALLOY 4270 Series are available in (4) speeds.The user has the ability to use different speeds of TUFFALLOY 4270, typically using a slower speed initially and increasing to a fast set, 1 minute working life.PROCESSING: TUFFALLOY 4270 Series can be pressure cast, vacuum cast, or open cast. For best results, TUFFALLOY 4274/75 should be used with Hapco's metering/dispensing equipment, RAPIDFIL, MINI FIL, and RAPIDSHOT.

KEBABLEND / WR 01/2120 is a special compound based on POM, which has very good sliding behavior and high wear resistance.

Titacon® TF910 is a 10％PTFE POWDER FILLED, WEAR RESISTANCE, MEDIUM FLOW.

PAR Group Nylon 6 Cast MoS2 Filled Sheet offers improved wear resistance and a higher load bearing when compared to standard nylon 6 grades. It has high strength, stiffness and hardness with high impact and fatigue resistance. We manufacture our own brand, Corromide® CMF (Cast Moly Filled) Nylon in sheets, rods and tubes. Our MoS2 filled Cast Nylon offers a higher temperature rating compared to the extruded grade. Nylon 6 Sheet - MoS2 Filled Cast is available to buy online at PAR Direct by clicking the link above.

Self-lubricating product based on Polyoximethylene (POM). Molybdenum dysulphide.

Nylene Duratel MF3 is a high-viscosity acetal co-polymer. Duratel MF3 has slightly higher toughness than standard MF9, and parts molded with MF3 should have thicker wall sections and shorter flow lengths to accommodate the higher viscosity. MF3 is suitable for such applications as clips, fasteners, gears, bushings and bearings, and other uses where long term creep and wear resistance are required.

VICTREX® 450CA30 is a high performance material that exhibits high strength and heat resistant properties. Glass-filled grades provide improved rigidity and dimensional stability.

GEHR PEEK® can be used at very high temperatures (about +260 °C) and it shows an extraordinary mechanical strength, toughness, hardness, flexural strength, torsional strength. PEEK exhibits excellent chemical resistance, very good dielectric properties up to +260 °C and a very good resistance to all kinds of radiation (even ultraviolet rays only lead to a slight yellow discolouration). PEEK is self-extinguishing properties according to UL 94.

The SOLLAMID B 2700 V0 features Polyamide 6 Flame Retardant. Presented in natural, black and color in customer pattern.

MECHETEC® Delrin® (polyoxy-methylene) offers design engineers a superior blend of strength, stiffness, lubricity, and dimensional stability. These properties, along with inherent machining ease, have made MECHETEC® Delrin® one of the most widely used engineering grade thermoplastics. To meet specific application configurations and to maximize production efficiencies, Polymer Industries offers a broad array of MECHETEC® Delrin® stock shapes. These materials include both homopolymer unfilled grades as well as PTFE-filled grades for enhanced wear resistance and DE-588 options for military applications. Formally known as Unital Delrin. For more Info : Click Here

Pfluon Chemical 8200FC30 is a abrasion reinforced Wear resistant particle,standard viscosity,black color and capable for plastic forming process like injection, squeeze etc.

Self-lubricating product based on Polycarbonate (PC). PTFE.

PA 66 reinforced with mineral filler