Products in Oil, Gas & Mining: Good Mechanical Properties

SMCarbon® 80CF40-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

3B Fiberglass SE 1043 consists of continuous glass filaments bonded into a single strand and wound onto a bobbin shape without twist. A proprietary sizing applied on the fibers assures an excellent resin-to-glass bonding. Corrosion resistant SE 1043 Fibreglassmade of E-CR glass is specifi-cally designed for the manufacturing of composites pipes and under-ground & chemicals tanks. SE 1043 is also used in pultrusion to manufacture profiles and in weaving-knitting processes. SE 1043 is tested in compliance with BS 14020 and IS 11320.

D2-440-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

SMCarbon® 24CF40-12K - Sheet molding compound based on vinyl ester resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Nitrile 4262-75 is a excellent compatibility with drilling muds and petroleum oils; withstands service demands of heavy equipment hydraulic systems; Parco’s lowest compression-set, sulfur-cure nitrile.

D4-115-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

D3-220-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

SMCarbon® 80CF60-3K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Polyumac Air-Cell T-60 is a hybrid, closed cell cross-linked polyester foam core that is an economical alternative to other cores used in the production of sandwich composite structures. In addition to its excellent strength to weight ratio, it offers good dimensional stability at elevated temperatures.

3B Fiberglass SE 4220 are corresponds to 3B’s portfolio of direct roving glassfi bre designed to rein-force polyolefi ns. Made out of E-CR glass, these direct roving fi bres consist of conti-nuous fi laments bonded together into a single strand and wound into a cylindrical shaped bobbin. SE 4220 (17μm) corresponds to an E-CR glass made direct roving whose strand consists of gathered 17μm diameter glass fi laments for reinforcing polyolefi ns. This 17μm fi lament diameter product offers the best compromise between mechanical performances and aptitude for knitting/weaving in the case of Continuous Fiber Thermoplastics manu-facturing. This is also the most common fi lament diameter in use for the production of LFT pellets or D-LFT parts. SE 4220 (17μm) is compatible with both polyethylene (PE) and polypropylene (PP).SE 4220 (17μm) direct roving is internal/inside pull and is available in 1200 tex and 2400 tex linear densities.

Nitrile 0209-70 is a high ACN content with low plasticizer level provides excellent resistance to petroleum oils, automatic transmission fluid (ATF), and crude oil; formulated as a transfer-moldable variant of Parco general-purpose nitrile 4200-70 for producing thick cross-section custom molded parts; used extensively in oil tool seals and packing elements for pressures to 1,500 psi.

Polynt Group SMC LS 3200 R40 is a sheet molding compound based on an unsaturated polyester resin reinforced with glass fibers. This SMC has been developed for structural parts. SMC LS 3200 R40 meets mechanical and thermal properties with reduction weight of the final parts. SMC LS 3200 R40 is formulated according to RoHS, REAC regulation SVHC and WEEE European legislation.

D1-115-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

D1-440-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

Nitrile 4456-70 is containing no ester plasticizers, compound 4456-70 provides superior compatibility with ABS, polycarbonates and other stress-sensitive plastics used in injection-molded automotive power steering seals.

Polynt Group SMC LS 3200 R20 C20 is a sheet molding compound based on an unsaturated polyester resin reinforced with glass fibers. This SMC has been developed for structural parts. SMC LS 3200 R20 C20 meets mechanical and thermal properties with reduction weight of the final parts. SMC LS 3200 R20 C20 is formulated according to RoHS, REAC regulation SVHC and WEEE European legislation.

SMCarbon® 80CF50-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

DISTITRON® 279 - Unsaturated polyester resin in styrene,Ortophthalic-Neopentylic. It is used to produce bmc and smc manufacture,very good mechanical properties through hot press molding method.

Nitrile 4457-65 is nitrile seal ideal for use in low temperatures and hydraulic fluids.Parco 4457-65 seals are suitable for applications ranging from -65 to +200°F.

D1-027-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

Nitrile 4465-65 is formulated expressly for use in low-temperature aviation fuel systems; low ACN content enables compounds to meet requirements of Aerospace Materials Specification (AMS) 7271, QPL listed, including passing low-temperature fuel seal test at -65°F.

D4-110-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

Enchuan 6120 is an non-wax non-thixotropy, and non-accelerator resin. It has the good physical properties and excellent performance in the fabrications of pipes and tanks that apply filament winding processes.

BMCarbon® 30CF60-6mm - Bulk molding compound based on Vinylester resin and reinforced with carbon fibers designed for compression molding technology. These materials with a potential weight reduced and a freedom high design enter different areas for structural application where high mechanical properties are requested.

RECarbon® 90CF40-400gr - Recycled molding compound based on epoxy resin and reinforced with reinforced with carbon fleece designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Nitrile 4067-70 is nitrile seal ideal for use in low temperatures and hydraulic fluids. Parco 4067-70 seals are suitable for applications ranging from -65 to +240°F.

D4-200-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

TBK-100(100) is a Basalt fabrics for reinforced plastics. It's a perfect insulation, reinforcing and filter medium.

DISTITRON® 184 - Unsaturated polyester resin in styrene,Isophthalic-Neopentylic. It is used to produce bmc and smc manufacture,very good mechanical properties through hot press molding method.

Polynt Group SMC LS 3800 R25 RF C NERO is a sheet molding compound based on an unsaturated polyester resin, fire retardant grade, reinforced with glass fibers. SMC LS 3800 R25 RF C NERO has been developed for application where is requested anti-static protection SMC LS 3800 R25 RF C NERO joint good mechanical properties mainly for impact resistance. SMC LS 3800 R25 RF C NERO is formulated according to RoHS, REAC regulation SVHC and WEEE European legislation.

Polyumac Air-Cell T-80 is a hybrid, closed cell cross-linked polyester foam core that is an economical alternative to other cores used in the production of sandwich composite structures. In addition to its excellent strength to weight ratio, it offers good dimensional stability at elevated temperatures.

D2-110-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

DISTITRON® 3584 - Pure maleic unsaturated polyester resin in styrene. It is used to produce bmc and smc manufacture,very good mechanical properties through hot press molding method.

SMCarbon® 26CF30-12K - Sheet molding compound based on vinyl ester resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Owens Corning M715 chopped strand mat represents a compelling solution in contact molding applications where quick wetting, rapid air release, good conformability and low resin consumption are desired. Produced with patented Advantex® corrosion resistant E-CR glass by Owens Corning. Made of medium tex multi-chop strands randomly dispersed and bonded together with a highly soluble polyester powder binder. Compatible with polyester, vinyl ester, and epoxy resins.

C-TAPE™ U600P 24K HS FT* is a unidirectional carbon fiber tape with a continuous weft, with a total weight of 606 gsm. It is made using 24K HS carbon fiber. The binding provided by the weft, along with the addition of fine warp threads, ensures the regularity of the product’s appearance; This carbon tape is used primarily for local reinforcement with epoxy resin. * FOE fiber available upon request