Products in Refining & Gas Processing: Good Mechanical Properties

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

CompositeWrap™ BDC20 Carbon Fabric is a medium weight, high tensile strength bidirectional carbon fabric. This material is engineered to provide extremely strong, durable and lightweight composites for structural reinforcement. CompositeWrap™ BDC20 Carbon Fabric is easy to apply, corrosion resistant and can be applied at any thickness required to provide adequate structural reinforcement. It easily wets out and can be installed using the wet lay-up technique.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, Compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

CompositeWrap™ UDC20 Carbon Fabric is a medium weight, high tensile strength unidirectional carbon fabric. This material is engineered to provide extremely strong, durable and lightweight composites for structural reinforcement. CompositeWrap™ UDC20 Carbon Fabric is easy to apply, corrosion resistant and can be applied at any thickness required to provide adequate structural reinforcement. It easily wets out and can be installed using the wet lay-up technique.

SMCarbon® 26CF40-12K - Sheet molding compound based on vinyl ester resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

SMCarbon® 24CF40-12K - Sheet molding compound based on vinyl ester resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

D1-115-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

SMCarbon® 90CF50-3K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

SMCarbon® 24CF60-3K - Sheet molding compound based on vinyl ester resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

C-TAPE™ U300P 12K HS FT* is a unidirectional carbon fiber tape with a continuous weft, with a total weight of 310 gsm. It is made using 12K HS carbon fiber. The binding provided by the weft, ensures the regularity of the product’s appearance; This carbon tape is used primarily for local reinforcement with epoxy resin. * FOE fiber available upon request

BMCarbon® 70CF45-12mm - Bulk molding compound based on Epoxy resin and reinforced with carbon fibers designed for compression molding technology. These materials with a potential weight reduced and a freedom high design enter different areas for structural application where high mechanical properties are requested.

Polyumac Air-Cell T-100 is a hybrid, closed cell cross-linked polyester foam core that is an economical alternative to other cores used in the production of sandwich composite structures. In addition to its excellent strength to weight ratio, it offers good dimensional stability at elevated temperatures.

D2-480-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

D1-240-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

SMCarbon® 90CF60-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

SMCarbon® 90CF40-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

D1-480-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

D1-041-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

SMCarbon® 90CF60-3K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

Kamenny Vek BCS 13-1/4”-KV02M is mainly recommended for friction material production using phenolic resin and for production of compounds by extrusion process with polyamide, polypropylene, polyethylene or high density.

D3-440-AB Boron-free glass direct rovings or single-end continuous rovings are designed for use in filament winding, pultrusion and weaving applications in polyester, vinyl ester or epoxy resin systems. Typical products include pultrusion profiles such as window frames, ladders, telecommunication cables and gratings. High-voltage insulating rods, tanks and pipes, etc. are also included.

RECarbon® 24CFP40-400gr - Recycled molding compound based on vinyl ester resin and reinforced with pyrolized carbon fleece designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

DISTITRON® 275 - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce bmc and smc manufacture,very good mechanical properties through hot press molding method.