Products in Other Power, Water & Utilities Applications: Tanks

Mica Is A Generic Term Applicable To The Group Of Complex Aluminosilicate Minerals That Occur Naturally In Plate Or Sheet-Like Form.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Mica Is A Generic Term Applicable To The Group Of Complex Aluminosilicate Minerals That Occur Naturally In Plate Or Sheet-Like Form.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Microglass milled fibers are E-glass filaments. Microglass is used as reinforcement in composites to increase mechanical properties (impact, tensile, compressive and flexural), improve dimensional stability and minimize distortion at elevated temperatures.

Mica Is A Generic Term Applicable To The Group Of Complex Aluminosilicate Minerals That Occur Naturally In Plate Or Sheet-Like Form.

ATTSHIELD OP 745 is used and recommended for boats, water tanks, septic tanks, bathtubs, cooling towers, and other items. By hand molding and spraying.

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

APCM DA 4092 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

ATTSHIELD OP 145 is recommended for water tanks, septic tanks, bathtubs, cooling towers, and other similar applications.

APCM DA 4082 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

ATTSHIELD XO - Unsaturated isophthalic polyester resin with good mechanical and glass wetting properties. The resin is thixotropic, has been accelerated, and has a low styrene emission system. At normal room temperature, cure with methyl ethyl ketone peroxide (MEKP).

APCM DA 4518 E-Glass is a modified epoxy system coated on heavy weight unidirectional E-Glass fibers. This product is designed to build excellent unidirectional strength using a minimum number of plies. DA 4518/E-Glass Uni also features extended room temperature out time and service temperatures to 300°F.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

APCM DA 409U/G35-150 is a tough, versatile, modified epoxy resin prepreg that cures at 250°F, a standard modulus 150 g/m2 carbon prepreg tape which can also be supplied as a 200g/m2 or a 300 g/m2 prepreg.

Attshield 47 is a novolac epoxy vinyl ester resin that resists corrosion in a wide range of solvent, acidic, and slightly alkaline environments. This tough, high-strength resin is used to make fiberglass-reinforced laminates with high impact strength and resistance to a variety of mechanical stresses. This resin is ideal for filament winding and the production of products that require resistance to harsh environments and temperature changes. This resin has excellent wettability and curing properties as well.

APCM DA 4080 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

APCM DA 4518 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 250°F (121°C) for one hour and or a cure of 350º F (177ºC) for 1 hour. This material needs to be post cure or cured to 350ºF to get the 350º properties.