Products in Power & Utilities: Epoxy & Epoxy Derivatives

ARCOR® 8510 is a solvent-free product that offers a unique blend of ceramics and special surface toughening agents, making it the most wear-resistant option available in its category. It is specifically designed for application in a single thick coat, with a thickness of up to 60 mils. This makes it an ideal material for protecting areas of fluid flow equipment that are prone to high wear. Additionally, it exhibits good chemical resistance and provides insulation against bi-metallic corrosion. ARCOR® 8510 offers excellent resistance to cavitation, further enhancing its durability and reliability. It is a top choice for effectively safeguarding equipment subjected to demanding wear and harsh environments. ARCOR Epoxy Technologies can tailor make or reformulate the product to suit customer needs. Please reach out if you need a custom formulated product!

8329TCF is a thermally conductive, fast-cure two-part epoxy adhesive. It is off-white, smooth, viscous, thixotropic, and bonds well to a wide variety of substrates. It is also flame retardant and meets the UL 94V-0 standard. For a 1 mL quantity, a minimal service cure can be achieved in 15 minutes at room temperature, and a full cure in 4 hours. This product is used to bond heat sinks, LEDs and other heat-generating components in electronic assemblies. It is suitable for use with dual-syringes, mix-tips and automatic dispensing systems. 8329TCF has been designed for maximum thermal conductivity with a high viscosity. For a lower viscosity, use 8329TFF. For a longer working life, use 8329TCM or 8329TCS.

8329TCS is a 2-part, heat-cure, thermally conductive epoxy adhesive with a 4-hour working time. It is a dark gray, smooth, thixotropic paste that cures to form a hard, durable polymer that is thermally conductive, yet electrically insulating. This thermal adhesive is used to glue heat sinks to LEDs, CPUs and other heat-generating components. 8329TCS has been designed for maximum thermal conductivity. It is highly viscous and must be mixed by hand prior to application. For a lower viscosity, use 8329TFS. For a shorter working time, use 8329TCM.

8329TFF is a 2-part, flame retardant, thermally conductive epoxy adhesive with a 5-minute working time. It is an off white, smooth, thixotropic paste that cures to form a hard, durable polymer that is thermally conductive, yet electrically insulating. This thermal glue is often used to bond heatsinks to CPUs, LEDs and other electronics components. This product has a very short working time. For a longer working time, use 8349TFM or 8329TFS.

SMCarbon® 80CF60-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

EPOLAM 2020 is a Variable reactivity by addition of an accelerator Tg ~80°C

SMCarbon® 90CF60-3K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

SMCarbon® 90CF50-3K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

Magna-Tac™ TR-8899 is a one part formulated thermosetting epoxy designed to adhere metals and alloys in transformer cores, as well as electric motor rotors and stators. It is a translucent, low viscosity adhesive and is generally applied by roller, dipping or spray.

SMCarbon® 90CF60-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

SMCarbon® 90CF40-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

Biresin® CR131 is an epoxy resin system suitable for the production of high performance fiber reinforced composites parts and molds with thermal properties up to 130°C.

APCM DA 4518U is a tough, versatile, modified epoxy resin system that cures at 250°F to 350°F. DA4518U can be supplied as a prepreg tape coated on unidirectional graphite.

Magna-Tac™ E645 is a two-part, thermosetting, formulated epoxy adhesive for bonding stack laminations used in stators, rotors, gyros, servomechanisms, synchros, transformers and magnetic amplifiers. It can also be used as an insulating varnish for impregnated coils and small electrical equipment. Bonding is achieved by heat. Only sufficient pressure to assure complete contact is needed.

EPOLAM 2022 is a Variable reactivity by addition of an accelerator Tg ~80°C

SMCarbon® 80CF60-12K/2 is generally used in automotive, industrial sector, leisure and clothing applications.

Anchor Seal SY6009T* Black is anchor-seal epoxy for potting compounds and encapsulants coils and transformers. It is used in low health hazard, thermal conducting switches.

SMCarbon® 80CF40-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

APCM DA 4080 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

APCM DA 4082 is 200°F cure modified epoxy prepreg system which can be prepreged on fiberglass fabric, woven Kevlar, or other woven fabrics. In addition to their low temperature cure capabilities, DA 4080 prepregs have excellent flow to allow for vacuum bag cure conditions. DA 4080 is a one sided pre-impregnated system yielding a single sided tack material. DA 4082 is the same system except that both sides of the fabric are coated yielding a double sided tack material. Both prepregs can be used for laminating and honeycomb sandwich construction.

APCM DA 4092 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

EPOVIA KAYAK KF3202L Series - Elastomeric BPA-epoxy vinyl ester resin. Main Applications areas are Aeolian,Aeronautical,Agrochemical,Agrobusiness,Automotive,Building and Construction,Composites,Consumer Products,Home and Domestic Applications,Industrial sector,Marine,Mass Transports,Railway Sector etc.

APCM DA 4518 E-Glass is a modified epoxy system coated on heavy weight unidirectional E-Glass fibers. This product is designed to build excellent unidirectional strength using a minimum number of plies. DA 4518/E-Glass Uni also features extended room temperature out time and service temperatures to 300°F.

APCM DA 4090 is modified epoxy pre-impregnated system which can cure at 250°F (121°C) for one hour. DA 4090 | DA 4092 can be supplied on any commercially available glass, Kevlar, or graphite fabric. DA 4090 is a one sided pre-impregnated fabric yielding a single sided tack material. DA 4092 is the same system where both sides of the fabric are pre-impregnated yielding a double sided tack material. Both prepreg systems can be used for laminating and honeycomb sandwich construction.

SMCarbon® 80CF60-3K/2 is generally used in automotive, industrial sector, leisure and clothing applications.

APCM DA 409U/G35-150 is a tough, versatile, modified epoxy resin prepreg that cures at 250°F, a standard modulus 150 g/m2 carbon prepreg tape which can also be supplied as a 200g/m2 or a 300 g/m2 prepreg.

Good properties of impregnation and bonding of wood. Germanischer Lloyd approved for EPOLAM 2017 and 2018 hardeners Tg ~80°C.

SMCarbon® 90CF50-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. This epoxy based SMC is suitable only for application with thickness of 15 mm at maximum.

Biresin® CR144 is a three component, anhydride cured, low viscosity epoxy resin system suitable for the production of high performance fi bre reinforced composites.

UDCarbon® 90CF60-12K is a unidirectional molding compound based on epoxy resin and reinforced with continuous carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Biresin® CR141 is a three component, anhydride cured, low viscosity epoxy resin system suitable for the production of high performance fi bre reinforced composites.

APCM DA 409U/S2-glass is a tough, versatile, modified epoxy resin prepreg that cures at 250ºF. The S-2 glass is a Zentron High Strength fiber. Standard weight is 260g/m2 with a 38% resin content. Other weights and resin contents available upon request.

APCM DA 4517 is an epoxy prepreg designed for a temperature range of -67°F (-55°C) to 350°F (177°C), with a cure of 180°F (82°C) for three hour. Shorter cures times are available at higher temperatures. The system is designed to be post cured if the higher temperature service range is required.

Epovia Optimum® KRF-1051 - novolac epoxy vinyl ester resin, chemical and heat resistance, low color, low foaming, fast cure. Main applications areas are building and construction, chemical industry, industrial sector etc.

SMCarbon® 80CF50-12K - Sheet molding compound based on epoxy resin and reinforced with carbon fibers designed for compression molding technology. These material with a weight reduced potential and a high design freedom enter different areas for structural application where high mechanical properties are requested.

Anchor Seal SY3002 Amber Clear is anchor-seal epoxy for potting compounds and encapsulants coils and transformers. It is good / stable shelf life, low viscosity, unfilled, heat and chemical resistant.