Products in Packaging Coatings: Flattener

PPG LO-VEL® HSF flatting agent is a synthetic amorphous silicon dioxide designed to reduce the gloss of high-solids, low volatile organic compounds (VOC) coatings.

CERETAN® MM 8220 is a Spherical, micronized, partially saponified Montan wax (Montan wax "OP"). This product in paints and coatings is used as an excellent matting effect, ideal surface properties, wax density ca. 1.00 g/cm³ analog to water and oils, ideal for low surfactant formulations, very good adhesion on uneven, porous, flexible and soft grounds, less hydrophobic than other micronized waxes, for hydrophilic systems/pigments, and in Masterbatch it is used as a dispersing agent, lubricant, 100 to 400 times smaller particles compared to course powder (e. g.“Montan wax OP powder“).

euroMinerals intalc is white, hydrophobic, flexible, soft therefore versatile. Depending on specifications, the different types of talc are used for the intalc products and are manufactured in different production processes: intalc is a top quality product, produced in a wide range of fineness.

Deuteron SO 300 is a fine dispersion of an elastomer in water. It imparts coatings with a “soft touch” surface, even if the binder is not an especially soft or elastic type. At the same time it acts as a matting agent. The effect depends on the dosage and the system’s other components, particularly the binder. Deuteron SO 300 is temperature resistant up to 160 °C.The small particle size makes the product suitable for thin-film applications. Deuteron SO 300 contains no waxes and thus does not negatively affect the recoatability.In 2-component lacquers, the inherent OH-functionality allows the product to be cross-linked in the coating matrix. This can lead to higher mechanical and chemical resistances, which are not attainable by conventional means of adjusting “soft touch” and matting.Application Deuteron SO 300 is intended for all water-based lacquers, coatings and printing inks which have to offer a special feel and matting up to a “soft touch”. It can be used in systems of all ranges of film thickness. Deuteron SO 300 can be combined with other organic matting agents, waxes and silicas. back

CERETAN® MM 8920 is a spherical, micronized modified Montan wax.This product have excellent rub and scratch resistance matting ideal surface properties wax density approx. 1,00 g/cm³ analog to water and oil, ideal for low surfactant formulations excellent adhesion on porous, uneven, flexible and soft substrates Less hydrophobic than other micronized waxes For hydrophilic systems / pigments Application are high quality paints and coatings e.g. powder, can, automotive, industrial, furniture and parquet coatings as well as UV- curing systems High quality printing inks e.g. overprint-, screen-, flexo-, offset and intaglio inks

PPG LO-VEL® 27 flatting silica is a highly efficient synthetic amorphous silicon dioxide flatting agent designed to reduce the gloss of lacquers and other coatings systems where a Hegman value of 6 to 6.5 is required.

Finma-Sil 30X-5W are aqueous matting agent concentrates with a very broad compatibility in all tested water-based systems, including acrylate and polyurethane dispersions.

LUBA-print® C 10/XB is a wax dispersion / wachsdispersion product.Uses in wood varnishes. Our high quality wax emulsions and dispersions are a necessity for all customers who prefer working with ready-made emulsions or dispersions in contrast to a dry wax. The ease of incorporation is the key benefit of liquid products.

CERETAN® MXS 3615 is a spherical, micronized carnauba wax, coated with silica.In Powder metallurgy Application Powder metallurgy Paints and coatings, such as industrial and wood coatings Printing inks.CERETAN ® micronized waxes are predominantly produced using our highly advanced spraying technology leading to spherical particles. The spherical shape and the particles’ even surface help the dispersing process, reduce wax usage as well as dust formation. We guarantee D99 values to minimize oversized particles in your formulation.

Pergopak® M3 is used as a matting and effects agent for the coatings industry imparting high matting efficiency, low impact on rheology, improved scratch and abrasion resistance, improvement of adhesion and elasticity, excellent weather resistance and gloss retention.

Sylysia SY 276 is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

Weifang Jahwa Chemical Barium Stearate is used in PVC compounds, rigid PVC pipes and cables, PVC profiles and flooring, PVC footwear, masterbatches. it is a heat stabilizer and lubricant for transparent PVC compound. It is generally used in conjunction with other stabilizers cadmium stearate and lead stearate. A combination of barium, zinc and calcium stearate can be used as a stabilizer in food grade PVC processing. Due to high melting point barium stearate is used for high-speed calendaring. It is used as a flatting and sanding agents in lacquers, coatings and inks. It is also used as drying lubricants and dusting agents for rubbers.

Sylysia SY 290 N is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

PPG LO-VEL® 2000 silica is a synthetic amorphous silicon dioxide flatting agent that delivers performance similar to silica gels in coatings formulations.

CERETAN® ME 0825 WD is a spherical, micronized, surface-modified Polyethylene wax and have uses in Paints and coatings and Printing Inks. This product have very good scratch- and abrasion resistance properties.CERETAN ® micronized waxes are predominantly produced using our highly advanced spraying technology leading to spherical particles. The spherical shape and the particles’ even surface help the dispersing process, reduce wax usage as well as dust formation. We guarantee D99 values to minimize oversized particles in your formulation.

Deuteron MM 682 is suited for all common coil-coating systems. This includes its utilization in conventional high-quality stove enamels. In addition, Deuteron MM 682 can be used in a variety of applications, preferably in pigmented paints and lacquers.The matting effect induced with Deuteron MM 682 is highly resistant to mechanical influences („polishing“ or abrasion).Deuteron MM 682 does not contain any wax additives, thus coating layers equipped with it are not expected to cause any adhesion problems in multi-layer systems or repair coatings. back

Köstrosol® 1540 is an opalescent aqueous dispersion of amorphous silicon dioxide nanoparticles. This middle-size colloidal silica has a negatively charged surface (anionic) which is stabilized by Alkaline (Na+). Köstrosol® 1540 is a pure colloidal silica without any organic additives.

Deuteron MK-matting agents are suitable as exclusive matting agents for water-borne, solvent-borne and solvent-free systems, air-drying as well as stoving. They can also be used in printing inks, wood lacquers, UV-curing coatings, coil-coatings, lacquers on foils, aqueous wood- and furniture varnishes.The finer types are suitable where particularly thin dry films are applied or where very smooth surfaces have to be realized. The combination with inorganic matting agents is possible and leads to improved mechanical resistances. Scratch resistance and resistance against polishing will be increased.Deuteron MK matting agents are micro-ground resp. micronized powders. The fineness enables Deuteron MK-products to be used in a wide field of applications for producing satin-flat and satin-gloss coatings. The small binder demand of Deuteron MK only leads to a nonessential viscosity influence, which is important for UV-curing lacquers. Deuteron MK is resistant against solvents and chemicals which are customary in the paint industry. These products can also be used in exterior applications. Adjustments to specific requirements can easily be made due to the different particle sizes, available. back

Pergopak® M6 is used as a matting and effects agent for the coatings industry imparting high matting efficiency, low impact on rheology, improved scratch and abrasion resistance, improvement of adhesion and elasticity, excellent weather resistance and gloss retention.

Sylysia SY 256 NF is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

Michem® Guard 25 is water based dispersion promotes mar resistance and flatting properties in paint and coating formulations.

Sylysia SY 256 N is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

Sylysia SY 246 NF is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

Pergopak® M5 is used as a matting and effects agent for the coatings industry imparting high matting efficiency, low impact on rheology, improved scratch and abrasion resistance, improvement of adhesion and elasticity, excellent weather resistance and gloss retention.

PPG LO-VEL® 6000 silica is a synthetic amorphous silicon dioxide flatting agent designed for use where a Hegman value of 5 to 6 is required. A combination of high flatting at low use levels and ease of incorporation delivers expanded formulation flexibility.

Finma-Sil 30X-5 are aqueous matting agent concentrates with a very broad compatibility in all tested water-based systems, including acrylate and polyurethane dispersions.

CERETAN® MPS 3120 is a micronized polypropylene wax, coated with Silica.excellent matting effect high transparency excellent slip excellent scratch resistance good heat resistance. Application in paints and coatings, such as industrial paints, wood coatings, overprint varnishes and UV-coating systems.CERETAN ® micronized waxes are predominantly produced using our highly advanced spraying technology leading to spherical particles. The spherical shape and the particles’ even surface help the dispersing process, reduce wax usage as well as dust formation. We guarantee D99 values to minimize oversized particles in your formulation.

Sylysia SY 250 N is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

Pergopak-matting agents are suitable as exclusive matting agents for water-borne, solvent-borne and solvent-free systems, air-drying as well as stoving. They can also be used in printing inks, wood lacquers, UV-curing coatings, coil-coatings, lacquers on foils, aqueous wood- and furniture varnishes.The finer types are suitable where particularly thin dry films are applied or where very smooth surfaces have to be realized. The combination with inorganic matting agents is possible and leads to improved mechanical resistances. Scratch resistance and resistance against polishing will be increased.Deuteron MK matting agents are micro-ground resp. micronized powders. The fineness enables Pergopak M-products to be used in a wide field of applications for producing satin-flat and satin-gloss coatings. The small binder demand of Pergopak M only leads to a nonessential viscosity influence, which is important for UV-curing lacquers. Deuteron MK is resistant against solvents and chemicals which are customary in the paint industry. These products can also be used in exterior applications. Adjustments to specific requirements can easily be made due to the different particle sizes, available. back

Sylysia SY 290 is a white, free-flowing powders of amorphous, micronized silica. sylysia is characterized by the fine pore network and the narrow, defined particle size distribution. These parameters are precisely adjusted to meet a wide variety of applications.

CERETAN® MP 2120 is a micronized Polypropylene wax.In paints and coatings: Application Paints and coatings, such as powder coatings, industrial paints, architectural, furniture and floor coatings Printing inks, such as gravure, overprint, screen printing and flexographic inks Masterbatch, especially for end-use applications with PP fibers and foils.CERETAN ® micronized waxes are predominantly produced using our highly advanced spraying technology leading to spherical particles. The spherical shape and the particles’ even surface help the dispersing process, reduce wax usage as well as dust formation. We guarantee D99 values to minimize oversized particles in your formulation.