Products in Polymers & Resins: Vacuum Bagging

DISTITRON® 183 CS - Unsaturated polyester resin in styrene,Isophthalic. It is used to produce isothermal sandwich panels through press and vacuum molding method.

NORSODYNE® H 44173 - Unsaturated polyester resin in styrene,Isophthalic. It is used to produce marine,boats,pipes and tanks through centrifugal casting,filament winding,hand lay up and spray up,injection molding,rtm,press and vacuum molding,pultrusion method.

PRF Composite Materials RS-L135 exhibits good mechanical properties after curing at room temperature. If high temperature strength is not required, finished products made with the selection of hardeners up to RS-H136 may be used without further heat treatment. Post curing (heat treatment) will further enhance the mechanical properties and will also increase the heat resistance.

EPOVIA OPTIMUM® KRF 2000 SE - Brominated Epoxy Resin based vinyl ester in styrene. It is used as general purpose in filament winding,vacuum injection,hand lay up and spray up,pultrusion method.

Rhino Linings USA, Inc. 1301 Resin is a Standard Undiluted Epoxy Resin. The standard press mold epoxy system for composite laminates and parts. All listed hardeners cure very quickly at standard process temperatures 160°F – 210°F.

PRF Composite Materials RS-L285 has very low mixed viscosity, ensuring a fast and complete impregnation of reinforcement fibers without drainage on vertical surfaces. The addition of fillers such as colloidal silica, microballoons, metal powder etc., is also acceptable to obtain special properties. The RS-L285 epoxy resin system exhibits good mechanical properties after curing at room temperature. If high temperature strength (≥ +60°C) or aircraft approval is not required, finished products made with the selection of hardener RS-H285 may be used without further heat treatment. Post curing (heat treatment) will further enhance the mechanical properties and will also increase the high temperature strength, up to 100°C being achievable depending on the selected hardener and post cure cycle used. The properties indicated in this document may only be achieved by curing/post-curing above 50°C.

EPOLAM 8064 is a Low viscosity amine-cured laminating epoxy system showing excellent flexibility and high reactivity.

POLYNT 9153 KA - Unsaturated polyester resin in styrene,DCPD. It is used to produce isothermal sandwich panels through press and vacuum molding method.

DISTITRON® 1629 V2 - Unsaturated polyester resin in styrene,Isophthalic. It is used to produce reinforced plastics,general purpose through injection molding,rtm,press and vacuum molding method.

DISTITRON® 3519 BS - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce isothermal sandwich panels through press and vacuum molding method.

Havel Composites CZ sro Epoxy resin L 20 is a laminating resin suitable for most work processes lamination, especially in the aerospace industry. Epoxy resin for glass saturation, aramid and carbon fibers. Bonds wood, metals, styrofoam, etc. It is suitable for manual lamination, injection and vacuuming. See the R + G handbook for details p.69. Recommended hardeners: VE 2723, VE 2778, H 105 / B, VE 2896, EPH 161-VE 3261, SG all from R + G.

DISTITRON® 1402 SV2 - Unsaturated polyester resin in styrene,Orthophthalic. It is used to produce isothermal sandwich panels through hand lay up and spray up,press and vacuum molding method.

DISTITRON® 100 SV3 - Unsaturated polyester resin in styrene,DCPD. It is used to produce surficial protection (liner,top coat) through coating with glazing,spray and brush process method.

DISTITRON® VEef 220 V4 - Bisphenol-A Epoxy Resin based vinyl ester in styrene. It is used to produce reinforced plastics,general purpose through injection molding,rtm,press and vacuum molding method.