Products in Elastomers: Ethylene Propylene Diene Terpolymer (EPDM)

EPDM 80 B WRAS R1 [E6392] is an EPDM elastomer with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 70.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

EPDM 70 B WRAS R1 [E6029] is an EPDM elastomer with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 70.

EPDM 80 B WRAS G1 is a polymer made from ethylene, propylene, and a small number of diene monomers. These diene monomers provide cross-link sites that allow EPDM to be vulcanized. A small number of diene monomers form unsaturated groups pendant from the main saturated chain. These groups facilitate cross-linking reactions that do not affect the integrity of the polymer backbone.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

EPDM 50 B WRAS G1 is a polymer made from ethylene, propylene, and a small number of diene monomers. These diene monomers provide cross-link sites that allow EPDM to be vulcanized. A small number of diene monomers form unsaturated groups pendant from the main saturated chain. These groups facilitate cross-linking reactions that do not affect the integrity of the polymer backbone.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

PEXIDAN® SX554 pre-grafted base is mixed with a crosslinking catalyst masterbatch CM493, in the ratio 95:5, or CM497, in the ratio between 90:10 and 93:7.CM493 is a stronger catalyst suitable for wall thicknesses > 1.5mm and CM497 is a weaker catalyst suitable for small conductor sizes, such as 1 to 4 mm2. The system SX554:CM493 or SX554:CM497, has been approved for use at 1kV and has found uses up to 10kV, it is highly flexible and enables the production of soft rubber cables without the use of continuous vulcanization equipment. Crosslinking is obtained by exposure to moist or hot water immersion only.

DLR Elastomer Engineering Ltd EN 45545-2 is a black fire resistant Ethylene Propylene Diene Rubber (EPDM).EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

EPDM Peroxide 80 WRAS G is a Peroxide Cured EPDM elastomer, with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 80.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

EPDM 60 B WRAS G1 is a polymer made from ethylene, propylene, and a small number of diene monomers. These diene monomers provide cross-link sites that allow EPDM to be vulcanized. A small number of diene monomers form unsaturated groups pendant from the main saturated chain. These groups facilitate cross-linking reactions that do not affect the integrity of the polymer backbone.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

EPDM 70 B WRAS G1 is a polymer made from ethylene, propylene, and a small number of diene monomers. These diene monomers provide cross-link sites that allow EPDM to be vulcanized. A small number of diene monomers form unsaturated groups pendant from the main saturated chain. These groups facilitate cross-linking reactions that do not affect the integrity of the polymer backbone. EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

PEXIDAN® SX505NT pre-grafted base is mixed with a crosslinking catalyst masterbatch CM493 or CM497, in the ratio 95:5. The SX505NT:CM493 or SX505NT:CM497 systems have passed type-tests for use up to and including 36 kV. The graft compound contains a non-staining stabilizer and an effective tree retarder, giving outstanding long term retention of dielectric strength. This compound is typically used in conjunction with crosslinkable semi-conducting material for conductor and insulation shields. Crosslinking is obtained by exposure to moist or hot water immersion only.

Interep 75-2 EPDM cellular rubbers have an excellent aging resistance, a good temperature resistance range and good compression sets.

KEP® 430H produced by Kumho Polychem is a highly functional special synthetic rubber that is mainly used for automotive parts and has excellent resistance to heat, ozone, and chemicals. With a lower specific gravity compared with other synthetic rubbers, it can be applicable for high-filling mixing, meaning it has a high economic feasibility.

D10090 is EPDM based compound that is medium hard with dimension stability.

Unirubber EPDM Infill granule is for artificial (synthetic) turf on indoor and outdoor playing fields.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK7534 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

EB 1001 is a Ethyle Propylene Diene monomer with wire mesh. 125” Single Ply Aramid Inserted EPDM Belt[Press/Roto Cured].

RubberGard™ MAX PT Membrane features our RubberGard Max (reinforced) EPDM membrane with factory laminated 6" (152 mm) or 3′′ (76 mm) wide QuickSeamTM tape extending continuously along one 100' (30.5 m) edge of the panel. The pre-applied tape extends slightly beyond the edge of the MAX PT membrane to form a selvage edge.

Interep 79-2 EPDM Standard cellular rubbers have an excellent aging resistance, a good temperature resistance range and good compression sets.

American Biltrite AB-566 (FDA) is a Ethylene Propylene (EPDM) Polymer.

Goodyear Rubber Company of So. California EPDM polymer (Ethylene Propylene Diene Monomer rubber) is a type of synthetic elastomer characterized by wide range applications. Main properties of EPDM are its outstanding heat, ozone and weather resistance. EPDM exhibits satisfactory compatibility with hydraulic fluids, ketones, hot and cold water and alkalis.

JSR EP98 is super high filler loadingoil extended EPDM.

Unirubber Virgin EPDM Mulch is a mulch for protection, recreational surfaces and walkways.

EB 1200 is a Ethyle Propylene Diene monomer with aramid. 125” Single Ply Aramid Inserted EPDM Belt[Press/Roto Cured].

Climarub 1.3 is developed to reduce the environmental impact. It can replace traditional EPDM rubber resulting in considerably lower CO₂ emission. Technically, Climarub performs just as well as traditional EPDM rubber.

An Excellent Polymer for Calendering

Seals Eastern Compound 7045 is 80-duro EPDM.

Cooper Standard ISG A-KT 80-00 is a black color EPDM sheeting for drinking water. It is KTW, W270 and WRAS certified.

KEP® 070P produced by Kumho Polychem is a highly functional special synthetic rubber that is mainly used for automotive parts and has excellent resistance to heat, ozone, and chemicals. With a lower specific gravity compared with other synthetic rubbers, it can be applicable for high-filling mixing, meaning it has a high economic feasibility.

CHANNEL RUBBER STRIP is a commercial grade black EPDM channel.

Coruba Coru163 - White FDA Approved EPDM Rubber 60° shore is an FDA Approved grade of white EPDM synthetic rubber. Ideally suited where product needs to be FDA approved and needs to be non toxic.

Royaltherm 1721 a modified EPDM with a special silicone rubber. Royaltherm 1721 is supplied as a base compound that can be vulcanized with peroxides or sulfur/accelerator systems. Royaltherm 1721 is 55 - 65 Durometer when vulcanized with 1.8 phr of dicumyl peroxide. It can be blended with Royaltherm 1411 for intermediate hardness applications. Royaltherm 1721 is recommended for applications that require higher tensile strength than Royaltherm 1411. Royaltherm 1721 is also recommended for applications that require retention of mechanical strength at elevated temperatures, weather and moisture resistance, electrical stability and compression recovery at low temperatures.

RubberGard™ Fire Retardant (FR) EPDM Membrane is a non-reinforced, cured, single-ply roofing membrane that can be used in ballasted, fully adhered and mechanically attached systems.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5815 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

RubberGard™ Platinum EPDM PT is a non-reinforced EPDM membrane panel with 6" (152.4 mm) wide QuickSeamTM tape factory laminated continuously along one lengthwise edge of the panel. The pre-applied tape is flush with the edge of the membrane.

American Biltrite AB-563 is a Ethylene Propylene (EPDM) Polymer.

J. Allcock & Sons EPDM Granules is produced by the ambient grinding of EPDM waste / scrap material. EPDM is a rubber made from either a co-polymer of ethylene and propylene – which will be peroxide cured, or a ter-polymer which has a small amount of an unsaturated polymer added – this will be sulfur cured. The two different types are rigorously segregated, both as scrap and as finished crumb (or granules).