Products in Elastomers: Rotational Molding

PELPRENE™ P46D-01 is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America.Characteristics include: Flame Rated High Viscosity Wear Resistant

Santicizer® Platinum G-2000 is an efficient bio-based primary plasticizer that offers excellent heat stability, enhanced processability, and lower volatility than traditional General-Purpose Plasticizers. It can be used in techniques such as extrusion, calendaring, injection molding, rotational molding, and spread coating. It can be used in rubbers, epoxy resins, paints and coatings, as well as many other polymers. Santicizer® Platinum G-2000 has earned the U.S. Department of Agriculture (USDA) Certified Biobased Product label.

PELPRENE™ P80C is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated Good Flexibility

PELPRENE™ P50DFR is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated Flame Retardant

PELPRENE™ P90BD is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated High Viscosity Wear Resistant

PELPRENE™ P95C is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated Good Flexibility

PELPRENE™ P150M is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated Chemical Resistant Copolymer Good Processability Heat Resistant

PELPRENE™ P40B is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated Chemical Resistant Copolymer Good Processability Heat Resistant

PELPRENE™ P70B is a Thermoplastic Polyester Elastomer (TPEE) product. It is available in North America. Characteristics include: Flame Rated Chemical Resistant Copolymer Good Processability Heat Resistant

Broadway Colors Yellow- BGS 001 has its typical applications in general purpose, small to medium parts.

BIONOX® 3114 is a sterically hindered phenolic antioxidant for processing and long-term thermal stabilization. It is a highly effective, non-discoloring stabilizer, exhibits low volatility and high resistance to extraction and it is odorless and stable to light.

Broadway Colors Brown-BGS 006 has its typical applications in general purpose, small to medium parts.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

According to a study, about 80% of infection diseases start from surface contact. Bacteria and fungi are everywhere in our daily life, the microbe can quickly reproduce with suitable conditions. It may cause contamination, odors and infectious diseases. Anti-Microbial, Anti-Fungal additives will be integrated into the polymer during the manufacturing process to inhibit the growth and provide protection from microbes.

Broadway Colors Light Green- BGS009 has a medium stiffness and good flowability with typical applications in general purpose, small to medium parts.

Ficel® SBH II is used as Styrenics, Polyolefin.

MoldWiz® WB-4606 - A water-based external release agent that adheres to the mold walls and has no affinity for the resin. Multiple releases for each application can be achieved.

EKFLEX 883 is a colorless liquid plasticizer based on diisooctyl phthalate (DIOP) and isomers thereof, featuring excellent performance and providing great value for money.

McLube® 787 is a water-based, heat-cured emulsion designed to prevent prerelease of large rotationally molded parts and provide multiple releases per application. Delivered ready-to-use.

McLube® 973 is a water-based, heat-cured emulsion that forms a durable, protective film coating with semi-permanent qualities. Contains a catalyst to significantly shorten the heat-cure cycle.

Birch Plastics BirCom AM05 is the active antimicrobial ingredients prevent it from growing, producing energy, replicating or inhibiting any further growth. BirCom AM05 antimicrobial does not wear off or leach out over time and provides long-lasting and effective product protection from microbes.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

Suqian Unitechem Antioxidant 1010 is Pentaerythritol tetrakis[3-(3',5'-di-tert-butyl-4'-hydroxyphenyl)propionate] with low volatility, migration resistance, extraction resistance.Widely used in the heat processing of polypropylene, polyethylene, polyoxymethylene, ABS resin and so on, which can prolong the service life of plastic products.

Endex 3750™ is a 50% concentrate in a polymer carrier. It can be used in a wide range of commodity and engineering plastics, combining quality and efficiency with the benefits of versatility and cost effectiveness.

Broadway Colors Lime Green - BGS 059 has a medium stiffness and good flowability.

Ficel® HC AZ 40 is used as Flexible PVC, Rigid PVC, Polyolefin.

When the MPM® 2000 is added to polypropylene at levels ranging from 0.25% – 2.0%, it can produce high levels of beta crystallinity in molded or extruded parts. The high beta crystal content results in dramatically higher impact strength and ductility, with very little reduction in modulus or tensile strength. If the final fabricated article is produced by post-orientation of an extruded sheet at temperatures below the melting point of the beta crystal phase, then microvoids will develop, and the density of the article will go down, and its opacity will go up. In the case of oriented films it is possible to lower the final film density by 15% when uniaxial stretching is done (MOPP), and by up to 70% when biaxial stretching (BOPP) is done. In the BOPP process it is possible to make breathable films when high levels of porosity are achieved. When the thermoforming process is used, the processing window of polypropylene is broadened dramatically, and cycle rates can be increased by 25%. Material distribution in the final part is also improved leading to potential down-weighting of thermoformed food containers by 15%. Beta nucleation can also be used to increase the tensile strength of biaxially oriented geogrids allowing for down-weighting of 15-20%. MPM 2000 can be used effectively in polypropylene resins that are already alpha-nucleated with either sodium benzoate or talc, and MPM 2000 may also work in the presence of other alpha nucleants, such as certain pigments. MPM 2000 is colorless, and has broad food contact approvals.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

Endex 1040™ is a chemical foaming agent which utilizes innovative technology to produce superior quality foamed products. It has a high gas yield and the fast response time typical of exothermic chemical foaming agents, and generates fine, closed-cell foams, which result in moldings and extrusions of high quality.

HAPFLEX 700 & 800 products are a series of low hazard, colorless, high strength, elastomers available in Shore hardnesses from 65A to 72D. HAPFLEX 700 & 800 products exhibit high tensile strength, high tear strength, and excellent elongation. All HAPFLEX 700 & 800 products cure at room temperature and can be accelerated with heat.Another key attribute of the 700 & 800 SERIES is that the base color of all components is colorless. For user convenience, HAPCO has designed this series in 2 speeds so the user can "customize" production rates and cure times. The fast and regular versions can be blended to user customize the gel time and cure time.HAPFLEX 700 & 800 SERIES can be used for mechanical, electrical, and mechanical/electrical applications. In addition, HAPFLEX 700 & 800 products show superior water immersion properties and superior adhesion when used in combination with Hapco's one part PRIMER 200.

Broadway Colors Dark Blue - BGS 008 has its typical applications in general purpose, small to medium parts.

M.G. Polyblends RFM-50 has developed foaming agent masterbatch based on Exothermic blowing agent. This blowing agent is properly dispersed in a polyolefinic resin along with some specialty chemicals which helps in creating a very fine cell structure in Rotomolded LLDPE tanks. Since our Roto foam masterbatch is in pulverized form and hence there is saving in pulverization cost to our customer. A case study report is attached herewith for your reference and better understanding of our product.

Endex 1042™ is a chemical foaming agent which utilizes innovative technology to produce superior quality foamed products. It has a high gas yield and the fast response time typical of exothermic chemical foaming agents, and generates fine, closed-cell foams, which result in moldings and extrusions of high quality.