Products in Thermoset Elastomers: Ethylene Propylene Diene Terpolyme...

EPDM 70 B WRAS R1 [E6029] is an EPDM elastomer with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 70.

DLR Elastomer Engineering Ltd EN 45545-2 is a black fire resistant Ethylene Propylene Diene Rubber (EPDM).EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

PEXIDAN® SX505NT pre-grafted base is mixed with a crosslinking catalyst masterbatch CM493 or CM497, in the ratio 95:5. The SX505NT:CM493 or SX505NT:CM497 systems have passed type-tests for use up to and including 36 kV. The graft compound contains a non-staining stabilizer and an effective tree retarder, giving outstanding long term retention of dielectric strength. This compound is typically used in conjunction with crosslinkable semi-conducting material for conductor and insulation shields. Crosslinking is obtained by exposure to moist or hot water immersion only.

EPDM 80 B WRAS R1 [E6392] is an EPDM elastomer with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 70.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

PEXIDAN® SX554 pre-grafted base is mixed with a crosslinking catalyst masterbatch CM493, in the ratio 95:5, or CM497, in the ratio between 90:10 and 93:7.CM493 is a stronger catalyst suitable for wall thicknesses > 1.5mm and CM497 is a weaker catalyst suitable for small conductor sizes, such as 1 to 4 mm2. The system SX554:CM493 or SX554:CM497, has been approved for use at 1kV and has found uses up to 10kV, it is highly flexible and enables the production of soft rubber cables without the use of continuous vulcanization equipment. Crosslinking is obtained by exposure to moist or hot water immersion only.

EPDM Peroxide 80 WRAS G is a Peroxide Cured EPDM elastomer, with good physical properties & meets the requirements of BS 6920-1:2000 and BS EN681-1 WA 80.EPDM rubber has excellent heat, ozone and chemical resistance propertiesEPDM also has good physical properties and is resistant to polar fluidsLow-temperature properties require the polymer to be amorphous and low on ethylene (speak to the expert)Good electrical properties require high ethylene to facilitate high doses of inert mineral fillers to give good electrical resistanceEPDM rubber can be compounded to provide excellent electrical resistance

ETHYLENE PROPYLENE RUBBER (EPR/EPDM) 505A is an amorphous rubber with low molecular weight and high ENB content, 505A is able to be applied for various types of product by taking advantage of its good flow and high cure rate, By blending with diene type rubbers such as a natural rubber, 505A plays significant roles to improve their ozone resistance, 505A is also suitable for foam applications made by continuous curing and it produces various sponge products with low density.

A General Purpose Sponge and Tire Polymer

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK7534 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

E80Q is a peroxide-cured, Ethylene Propylene Terpolymer material formulated using only those ingredients determined by the US Food and Drug Administration (FDA). E80Q is suitable for use in food contact applications requiring FDA and 3A compliance.E80Q provides excellent water and steam resistance and good compression set properties. The material's heat and chemical resistance is superior to that of sulfur-cured EPDM.Available in any sized O-ring (fully molded up to 2.5m/8ft internal diameter), gaskets and custom designed components.Key Attributes FDA compliant to CFR 21 § 177.2600 (a-d) 3A Sanitary Standard 18-03 Class 2 compliant Free from Animal Derived Ingredients (ADI) Typical AttributesRecommended for use in food and dairy applications. O-rings Gaskets Hygienic/sanitary couplings & pipe connectors Valves Pumps Metering equipment

Seals Eastern Compound 7189 is 53-duro EPDM.

Precision Associates inc. 23618 is a 60 durometer black EPDM, formulated with Teflon to provide internal lubrication. It exhibits good resistance to heat, compression set and water and will remain non-brittle at very low temperatures.

KEP® 020P produced by Kumho Polychem is a highly functional special synthetic rubber that is mainly used for automotive parts and has excellent resistance to heat, ozone, and chemicals. With a lower specific gravity compared with other synthetic rubbers, it can be applicable for high-filling mixing, meaning it has a high economic feasibility.

JSR EP98 is super high filler loadingoil extended EPDM.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5810 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

POLIGOM is available in a wide range of SHORE HARDNESS with feature of flame retardant thermoplastic, halogen-free and exceptional flexibility. The product is available with high level of tensile strength, excellent levels of tear strength and free plasticizers (XEPR/XHEPR), and is also characterized by a particularly low value of Specific Gravity.

ETHYLENE PROPYLENE RUBBER (EPR/EPDM) is a non-oil extend grade with very high molecular weight and high ENB content, 5206 is especially suited for foam applications cured by continuous vulcanization. Sponge products with 5206 show good shape retention, low compression set and soft feeling.

E60 is a commercial grade black EPDM sheet and has good ozone, chemical and aging resistance.

Sulphur cured, white Ethylene Propylene Terpolymer, 75-85 °IRHD. Terpolymer of ethylene, propylene and diene monomers. Formulated using only those ingredients determined by the United States Federal Food and Drug Administration (FDA) to be in accordance with Code of Federal Regulations Title (CFR21), Section 177.2600 (a-e): "Rubber articles intended for repeated use".Material formulated for repeated use with aqueous foodstuffs intended for human consumption.

Unirubber Virgin EPDM Mulch is a mulch for protection, recreational surfaces and walkways.

POLIGOM is available in a wide range of SHORE HARDNESS with feature of flame retardant thermoplastic, halogen-free and exceptional flexibility. The product is available with high level of tensile strength, excellent levels of tear strength and free plasticizers (XEPR/XHEPR), and is also characterized by a particularly low value of Specific Gravity.

An Excellent Polymer for Calendering

D50045 is a EPDM based compound that has chemical resistant,heat resistant, weatherable and UV resistant

Royaltherm 1721 a modified EPDM with a special silicone rubber. Royaltherm 1721 is supplied as a base compound that can be vulcanized with peroxides or sulfur/accelerator systems. Royaltherm 1721 is 55 - 65 Durometer when vulcanized with 1.8 phr of dicumyl peroxide. It can be blended with Royaltherm 1411 for intermediate hardness applications. Royaltherm 1721 is recommended for applications that require higher tensile strength than Royaltherm 1411. Royaltherm 1721 is also recommended for applications that require retention of mechanical strength at elevated temperatures, weather and moisture resistance, electrical stability and compression recovery at low temperatures.

Unirubber EPDM Infill granule is for artificial (synthetic) turf on indoor and outdoor playing fields.

A High Ethylene, High Mooney Polymer for TPO Products and Extruded Mechanical Goods

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5812 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

Sulphur cured Ethylene Propylene Terpolymer 60-70 °IRHD. Terpolymer of ethylene, propylene and diene monomers. Formulated in accordance with BS2494 Type ‘W'.For joint rings, sealing rings and gaskets, and general applications where water and weathering resistance is required

POLIGOM is available in a wide range of SHORE HARDNESS with feature of flame retardant thermoplastic, halogen-free and exceptional flexibility. The product is available with high level of tensile strength, excellent levels of tear strength and free plasticizers (XEPR/XHEPR), and is also characterized by a particularly low value of Specific Gravity.

D50060 is a EPDM based compound that has chemical resistant,heat resistant, weatherable and UV resistant

A Highly Extendable DCPD Polymer with Heavy Hydrotreated Paraffinic Oil for TPO/TPV and Thermoset Applications

TPRR® 090 is a TPRR (Thermoplastic recycled rubber) material consisting mainly of recycled plastics and recycled rubber. Mainly used to comprised of recycled EPDM can replace LDPE, TPE and rubber materials.

Sulphur cured, off-white Ethylene Propylene Terpolymer, 55-65 °IRHD. Terpolymer of ethylene, propylene and diene monomers. Formulated using only those ingredients determined by the United States Federal Food and Drug Administration (FDA) to be in accordance with Code of Federal Regulations Title (CFR21), Section 177.2600. Extraction tested in distilled water.Suitable for repeated use with dry and aqueous foodstuffs intended for human consumption. Not suitable for use with fatty foodstuffs.

D50080 is a EPDM based compound that has chemical resistant,heat resistant, weatherable and UV resistant

A Polymer Highly Extended with Heavy Hydrotreated Paraffinic Oil for TPO and Extruded Thermoset Applications

A High Performance Sponge Polymer