Products in Thermoset Elastomers: Injection Molding

Moplen EP380T is a High flow polypropylene impact copolymer resin

A General Purpose Sponge and Tire Polymer

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK7534 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

KEP® 020P produced by Kumho Polychem is a highly functional special synthetic rubber that is mainly used for automotive parts and has excellent resistance to heat, ozone, and chemicals. With a lower specific gravity compared with other synthetic rubbers, it can be applicable for high-filling mixing, meaning it has a high economic feasibility.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5810 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

Moplen EP400L is a Polypropylene Impact Copolymer Resin

Royaltherm 1721 a modified EPDM with a special silicone rubber. Royaltherm 1721 is supplied as a base compound that can be vulcanized with peroxides or sulfur/accelerator systems. Royaltherm 1721 is 55 - 65 Durometer when vulcanized with 1.8 phr of dicumyl peroxide. It can be blended with Royaltherm 1411 for intermediate hardness applications. Royaltherm 1721 is recommended for applications that require higher tensile strength than Royaltherm 1411. Royaltherm 1721 is also recommended for applications that require retention of mechanical strength at elevated temperatures, weather and moisture resistance, electrical stability and compression recovery at low temperatures.

Ebalta GM 900-1 / Comp. A+B is a very soft-elastic polyurea casting compound. ebalta GM 900-1 is suitable as a flexible casting system in the field of mold- and tooling for parts which require low shore hardness and high tear propgation resistance due to deep under cuts. Mold temperatures of about 60 °C lead and/or curing at 60°C, to faster curing and therefore short demoulding time. Demoulding can be reduced to 30-40 min

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5812 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

Moplen EP649N is a medium flow heterophasic copolymer development grade with outstanding mechanical properties and antistatics. The product features an easy processability and an excellent stiffness combined with good impact properties and high gloss. This grade is suitable for a wide range of appliances parts, Toys and consumer goods industries. Moplen EP649N resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.

Moplen EP546T is a High flow, high crystalline polypropylene impact copolymer resin

Duradene™711 is a solution polymerized non-oil extended styrene-butadiene rubber copolymer. It contains 18.0% bound styrene and a non-volatile antioxidant stabilizer system. Duradene™711 offers excellent abrasion resistance and low temperature performance. It is often used in tire formulas with low black and oil loadings where good wear and hysteresis are desired.

TPRR® 090 is a TPRR (Thermoplastic recycled rubber) material consisting mainly of recycled plastics and recycled rubber. Mainly used to comprised of recycled EPDM can replace LDPE, TPE and rubber materials.

Epiall® 1908B-1 by Sumitomo Bakelite Company is comprised of Ethylene Propylene Copolymer. It is commonly used Epiall® 1908B-1 is certified as UL Flame Rated. It is available in Granules form.

Moplen EP300H is a heterophasic copolymermanufactured by PMC under the license of LyondellBasell using Spheripol process. Moplen EP300H is suitable for injection molding as well as for thermoforming applications. The features ofMoplen EP300H are an excellent low temperature impact resistance combined with a good processability. Moplen EP300Hmeets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5815 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

G&E 565 is produced from feedstocks carefully selected for uniform viscosity, ethylene propylene ratio and 3rd monomer. The feedstocks are chosen to produce a blended EPDM Polymer which has a high ethylene content, medium mooney and high diene. G&E Blended EPDM 565 can be blended with prime EPDM polymers to reduce compound costs in extruded, calendered and molded applications.

D10060 is EPDM based compound that is medium hard with dimension stability.

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5811 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

Polymer-Technik Elbe EPDM - Peroxide TWK7528 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

Moplen EP540N is a High crystalline polypropylene impact copolymer resin

Xenopren® E/P-TD-21-V0 is a non-flammable propylene-ethylen copolymer modified with talc. This plastic thanks to using copolymer has a good impact strength, even at low temperatures. Significantly decreased flammability of this Xenopren® allow for using it in all cases where, because of risk of fire and high temperature, extremely low flammability is required. Processing of Xenopren® E/P-TD-21-V0 requires injection molding machines with pressure of injection 80MPa. Recommended cylinder temperature should be about 230-2500C and mold temperature 500C.

Moplen EP548P is a nucleated heterophasic copolymer, suitable for injection molding applications, and contains an anti-static agent. It exhibits a high stiffness combined with a medium fluidity. Moplen EP548P is extensively used in houseware, furniture, cylindrical containers and crates. Moplen EP548P resin meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.

Duradene™706 is a solution polymerized non-oil extended styrene-butadiene rubber copolymer. It contains 23.5% bound styrene and has a non-volatile antioxidant stabilizer system. Duradene™706 offers very good abrasion resistance and low hysteresis properties. It can also be used as a replacement for emulsion SBR 1502 in most rubber applications.

Polymer-Technik Elbe EPDM - Sulfur TWK8684 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

Epiall® 1908-1 by Sumitomo Bakelite Company is comprised of Ethylene Propylene Copolymer. It is commonly used Epiall® 1908-1 is certified as UL Flame Rated. It is available in Granules form.

KEP® 070P produced by Kumho Polychem is a highly functional special synthetic rubber that is mainly used for automotive parts and has excellent resistance to heat, ozone, and chemicals. With a lower specific gravity compared with other synthetic rubbers, it can be applicable for high-filling mixing, meaning it has a high economic feasibility.

Moplen EP341R is a High flow, high crystalline polypropylene impact copolymer resin

Polymer-Technik Elbe EPDM - Elastomer Guideline TWK5813 has excellent ozone, aging and weather resistance which also has low pressure deformation residue even at high temperatures, very good resistance to hot water, hot steam, acids, alkalis and hydraulic fluids based on glycol water.

G&E 254 is produced from feedstocks carefully selected for uniform viscosity, ethylene propylene ratio, and 3rd monomer. The feedstocks are chosen to produce a blended EPDM Polymer which has a medium ethylene content, medium diene content, and low mooney. G&E Blended EPDM 254 can be blended with prime EPDM polymers to reduce compound costs in extruded, calendered and molded applications.

The product is a very soft elastic polyurea casting compound. ebalta GM 951-1 is suitable as a flexible casting system in the field of mold- and tooling for parts which require low shore hardness and high tear propagation resistance due to deep under cuts. Mold temperatures of about 60 °C lead and/or curing at 60°C, to faster curing and therefore short demoulding time. Demoulding can be reduced to 30-45 min. To achieve final properties as fast as possible, postcuring can be made at 60°C for 6-8 hrs. and after curing at room temperature. For complete curing of the parts, any non-postcured molds should only be employed after 2-3 days. Any non-observance may lead to shorter pot life. The potlife of GM 915-1 can be shortened by mixing hardener GM 951-1 with hardener GM 900-1 (see mixing table) For individuell formulation of the shore hardness, GM 900-1 can be mixed with GM 951-1 (see mixing table). With the A-component GM 951-1 Thix a spreadable surface resin can be obtained.

D10070 is EPDM based compound that is medium hard with dimension stability.

Moplen EP549T is a High flow, high crystalline polypropylene impact copolymer resin

An Ultra Fast Curing Polymer for Sponge and Dense Extrusions

Moplen EP300K is a low fluidity heterophasic copolymer manufactured by PMC under the license of Lyondellbasell using Spheripol process. Moplen EP300K is suitable for injection molding applications. The product exhibits very high impact even at low temperature combined with a good stiffness. Moplen EP300K is typically used in housewares and crates. Moplen EP300K meets the FDA requirements in the Code of Federal Regulations in 21 CFR 177.1520 for food contact.

D10050 is EPDM based compound that is medium hard with dimension stability.