Knowde Enhanced TDS
Identification & Functionality
- Additives Included
- Polymer Name
- Plastics & Elastomers Functions
- Technologies
Features & Benefits
- Materials Features
- Mechanical Recycling
Process
Debris are washed, melted & transformed into raw material for a new process. Focus on responsible sourcing of high-quality waste streams
Certification
Third-party certification of PCR content conducted by SCS Global Services
Value Proposition
- 21-80% post-consumer recycled content
- Meeting RoHS1 guidelines
- Provides CO2
- reduction & waste depletion options
- Non-brominated & non-chlorinated flame retardant systems
- Up to 2 extra EPEAT points can be achieved
- Broad color space, enhanced performance via
- blending with copolymers
- Drop in solution to existing tools
Applications & Uses
- Markets
- Applications
- Plastics & Elastomers End Uses
- Plastics & Elastomers Processing Methods
Properties
- Flame Rating
- Mechanical Properties
- Physical Properties
- Thermal Properties
- Impact Properties
- Injection Molding
- Flame Characteristics
- Note
- ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
- ᵖ UL ratings shown on the technical datasheet might not cover the full range of thicknesses and colors. For details, please see the UL Yellow Card.
- ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
- ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.
Value | Units | Test Method / Conditions | |
Flexural Modulus (at 2 mm/min) ¹¹ | 2280 | MPa | ISO 178 |
Flexural Strength (at 2 mm/min) ¹¹ | 91 | MPa | ISO 178 |
Tensile Modulus (at 1 mm/min) ¹¹ | 2130 | MPa | ISO 527 |
Tensile Strain (Break, 50 mm/min) ¹¹ | 132 | % | ISO 527 |
Tensile Strain (Yield, 50 mm/min) ¹¹ | 6.2 | % | ISO 527 |
Tensile Stress (Break, 50 mm/min) ¹¹ | 62 | MPa | ISO 527 |
Tensile Stress (Yield, 50 mm/min) ¹¹ | 58 | MPa | ISO 527 |
Tensile Modulus (at 50 mm/min) ¹¹ | 2070 | MPa | ASTM D638 |
Tensile Stress (Yield, Type I, 50 mm/min) ¹¹ | 58 | MPa | ASTM D638 |
Tensile Stress (Break, Type I, 50 mm/min) ¹¹ | 63 | MPa | ASTM D638 |
Tensile Strain (Yield, Type I, 50 mm/min) ¹¹ | 6.4 | % | ASTM D638 |
Tensile Strain (Break, Type I, 50 mm/min) ¹¹ | 130 | % | ASTM D638 |
Nominal Strain (Break, 50 mm/min) ¹¹ | 100 | % | ASTM D638 |
Flexural Strength (at 1.3 mm/min, 50 mm span) ¹¹ | 97 | MPa | ASTM D790 |
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹ | 2300 | MPa | ASTM D790 |
Value | Units | Test Method / Conditions | |
Density ¹¹ | 1.23 | g/cm³ | ISO 1183 |
Mold Shrinkage (flow) ᵍ ¹¹ | 0.4 - 0.8 | % | SABIC method |
Mold Shrinkage (xflow) ᵍ ¹¹ | 0.4 - 0.8 | % | SABIC method |
Water Absorption (at 23°C, 24hrs) ¹¹ | 0.14 | % | ASTM D570 |
Water Absorption (at 23°C, 24hrs) ¹¹ | 0.15 | % | ISO 62-1 |
Melt Volume Rate (at 300°C, 1.2 kg) ¹¹ | 16 | cm³/10 min | ISO 1133 |
Specific Gravity ¹¹ | 1.19 | - | ASTM D792 |
Melt Flow Rate (at 300°C, 1.2 kgf) ¹¹ | 17 | g/10 min | ASTM D1238 |
Value | Units | Test Method / Conditions | |
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 124 | °C | ISO 75/Af |
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹ | 138 | °C | ISO 75/Bf |
Vicat Softening Temperature (Rate B/50) ¹¹ | 142 | °C | ISO 306 |
Vicat Softening Temperature (Rate B/50) ¹¹ | 142 | °C | ASTM D1525 |
Vicat Softening Temperature (Rate B/120) ¹¹ | 144 | °C | ISO 306 |
Vicat Softening Temperature (Rate B/120) ¹¹ | 144 | °C | ASTM D1525 |
Coefficient of Thermal Expansion (at 23°C to 80°C, flow) ¹¹ | 0.000066 | 1/°C | ISO 11359-2 |
Coefficient of Thermal Expansion (at 23°C to 80°C, xflow) ¹¹ | 0.000072 | 1/°C | ISO 11359-2 |
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹ | 126 | °C | ASTM D648 |
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹ | 139 | °C | ASTM D648 |
Coefficient of Thermal Expansion (at 23°C to 50°C, flow) ¹¹ | 0.000066 | 1/°C | ASTM E831 |
Coefficient of Thermal Expansion (at 23°C to 50°C, xflow) ¹¹ | 0.000072 | 1/°C | ASTM E831 |
Relative Temperature Index (Electrical) ᵖ ¹¹ | 80 | °C | UL 746B |
Relative Temperature Index (Mechanical with impact) ᵖ ¹¹ | 80 | °C | UL 746B |
Relative Temperature Index (Mechanical without impact) ᵖ ¹¹ | 80 | °C | UL 746B |
Value | Units | Test Method / Conditions | |
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹ | 52 | kJ/m² | ISO 180/1A |
Izod Impact (Notched, 80*10*4, at 0°C) ¹¹ | 20 | kJ/m² | ISO 180/1A |
Izod Impact (Notched, 80*10*4, at -30°C) ¹¹ | 16 | kJ/m² | ISO 180/1A |
Izod Impact (Unnotched, 80*10*4, at 23°C) ¹¹ | 237 | kJ/m² | ISO 180/1U |
Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 59 | kJ/m² | ISO 179/1eA |
Charpy Impact (at 0°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 23 | kJ/m² | ISO 179/1eA |
Charpy Impact (at -30°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹ | 18 | kJ/m² | ISO 179/1eA |
Charpy Impact (at 23°C, Unnotch Edgew 80*10*4 sp=62mm) ¹¹ | 330 | kJ/m² | ISO 179/1eU |
Izod Impact (Notched, at 23°C) ¹¹ | 770 | J/m | ASTM D256 |
Izod Impact (Notched, at 0°C) ¹¹ | 600 | J/m | ASTM D256 |
Izod Impact (Notched, at -30°C) ¹¹ | 190 | J/m | ASTM D256 |
Izod Impact (Unnotched, at 23°C) ¹¹ | 2700 | J/m | ASTM D4812 |
Value | Units | Test Method / Conditions | |
Drying Temperature ⁷ | 120 | °C | - |
Drying Time ⁷ | 3 - 4 | Hrs | - |
Maximum Moisture Content ⁷ | 0.02 | % | - |
Melt Temperature ⁷ | 295 - 315 | °C | - |
Rear - Zone 1 Temperature ⁷ | 270 - 295 | °C | - |
Middle - Zone 2 Temperature ⁷ | 280 - 305 | °C | - |
Front - Zone 3 Temperature ⁷ | 295 - 315 | °C | - |
Nozzle Temperature ⁷ | 290 - 310 | °C | - |
Mold Temperature ⁷ | 70 - 95 | °C | - |
Back Pressure ⁷ | 0.3 - 0.7 | MPa | - |
Screw Speed ⁷ | 40 - 70 | rpm | - |
Value | Units | Test Method / Conditions | |
UL Recognized (94HB Flame Class Rating) ᵖ | min. 0.47 | mm | UL 94 |
Regulatory & Compliance
- Certifications & Compliance
Packaging & Availability
- Country Availability
- Regional Availability