Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Polymer Name
- Technologies
- Product Families
Features & Benefits
- Labeling Claims
- Materials Features
- Features & Benefits
Product Attributes Customer Benefits - Range of grades available
- Good tensile strength and high surface hardness
- Excellent chemical resistance
- Resists stress cracking.
- Natural product may be used in contact with foodstuffs
- PP-H may be hot air welded
- Low density – compared with other engineering plastics.
- Minimal absorption of moisture.
- Diameter (PP-H)
- Product sourced from longstanding manufacturer with ISO accreditation
- Correct grade selection for application is optimized
- Very good all-round product for diverse engineering applications
- Low cost assembly
- Easy handling, low inertia, energy saving
- Aids dimensional stability
- Huge components are possible
- Consistent quality ensures uniform characteristics in machining & performance
Applications & Uses
- Markets
- Plastics & Elastomers End Uses
- Typical Applications
PP-H - For pump and valve parts, gaskets, support stands for coating machines and spacers used in plating plant.
- Machinability
The machining of polypropylene is uncomplicated, provided the component tolerances allow for polypropylene’s relatively high co-efficient of thermal expansion and tensile elongation values. Full machining instructions can be supplied on request.
Properties
- Flame Rating
- Mechanical Properties
- Thermal Properties
- Typical Properties
- Electrical Properties
- Flammability
Value | Units | Test Method / Conditions | |
Density (20°C) | 0.91 | g/cm^³ | - |
Tensile Strength at Yield | 30.0 | MPa | - |
Elongation at Yield | 10.0 | % | - |
Elongation at Break | min. 50 | % | - |
Tensile Modulus of Elasticity | 1200.0 | MPa | - |
Impact Strength | No break | kJ/m^² | - |
Notched Impact Strength | 50.0 | kJ/m^² | - |
Ball Indentation Hardness / Rockwell | 67.0 | N/mm^² | - |
Hardness | 70.0 | Shore D | - |
Value | Units | Test Method / Conditions | |
Vicat Softening Point | 91.0 | ºC | VST/B/50 |
Heat Deflection Temperature | 96.0 | ºC | Method B |
Service Temperatures without High Mech. Load - Upper Limit | 100.0 | ºC | - |
Service Temperatures without High Mech. Load - Lower Limit | 5.0 | ºC | - |
Value | Units | Test Method / Conditions | |
Moisture Absorption | 0.01 | % | ISO 62 |
Value | Units | Test Method / Conditions | |
Volume Resistivity | min. 10^¹⁶ | ohm-cm | - |
Dielectric Constant (1 MHz) | 2.3 | - | - |
Dielectric Loss Factor (1 MHz) | 0.0002 | - | - |
Value | Units | Test Method / Conditions | |
Flammability | HB | - | UL94 |
Regulatory & Compliance
- Certifications & Compliance
- Physiological Safety
The FDA (US Food & Drug Administration) has approved the raw materials used for the PP-H grade to allow its use in contact with food – check for any specific limitations required by the FDA.
Technical Details & Test Data
- Technical Description
Grade Modification Purpose PP-H None. Colors, natural, light gray. Some sizes available in black. Component Identification Black will have better UV resistance - Chemical Resistance
PP-H has extremely good resistance to acids, alkalis and alcohol, salts in aqueous solutions and many solvents. Slight swelling may be caused by permanent contact with grease, oil and wax, but generally not enough to limit the use of the material. Aromatics and halogenated hydrocarbons will cause a reduction in useful working life. The material has no resistance to strong oxidizing agents such as nitric or chromic acids, and halogens.
Packaging & Availability
- Product Availability
Extruded round bar PP-H 10mm to 500mm dia in natural (600mm to 700mm dia in light gray PP-C and 30mm to 60mm in black PP-H) Hollow round bar in PP-H (light gray color) From 30mm o/d x 15mm i/d to 200mm o/d x 120mm i/d in 2m lengths. Other products -PP-H, light gray color. Square &hexagon bars. Rectangular & square hollow tubes, angles, channels and welding rod. Also handles & hinges for tank fabrication. * Sizes not stocked are available on relatively short delivery time. 1, 2 or 3m lengths supplied or cut to customer requirements.