Knowde Enhanced TDS
Identification & Functionality
- Carrier
- Technologies
Features & Benefits
- Labeling Claims
- Ready-to-Use Product Features
- Features
- Cold applied by notched squeegee or multi-port adhesive applicator capable of applying a minimum of ½ inch diameter beads.
- Cures to a tenacious flexible bond that resists cracking, moisture and chemical attack.
- Solvent Free.
Applications & Uses
- Markets
- Application Method
- Compatible Substrates & Surfaces
- Approved Substrates
- Structural Roof Decking: concrete, gypsum, cemetitious wood fiber (tectum).
- Base sheets.
- Approved insulations (multi-layer applications).
- Smooth built-up roof surfaces (recover applications).
- Primed concrete or masonry foundations.
- Approved Insulations
Insulation Type Min. Thickness (Inches) HD Wood Fiber (Coated 5 Sides) 25/32 Isocyanurate 1.2 Fiberglass 3/4 Perlite 3/4 Styrofoam 1/2 Note:
- Not recommended for insulation boards larger than 4’x4’.
- Application & Uses
- Ready to apply.
- Do not heat.
- Do not thin.
- Keep the container covered when not in use for the formation of skin.
- During application a wet cloth draped over the open container will assist in preventing rapid skin over.
- Surface Preparation
- All work surfaces must be clean, dry, free of dirt, dust, debris, oils, loose and/or embedded gravel, un-adhered coatings, deteriorated membranes, biological growth (mold, mildew, fungus, algae and moss), and other contaminants that may result in a surface that is not sound.
- On recovery work, to ensure a properly prepared surface use MAST&R Cleanse AR to clean substrate prior to application of QuikBond.
- Application Directions
- Apply QuikBond directly to the properly prepared substrate using a notched squeegee or multi-port adhesive applicator, achieving ½” - ¾” beads equally spaced from one another.
- Within 10 minutes of application, place insulation boards into the adhesive.
- Do not slide the board across the adhesive.
- Do not allow the adhesive to skin over or step each board into place to ensure contact with the adhesive.
- Substrates with irregular surfaces may prevent the adhesive from making and/or maintaining positive contact with the adhesive.
- Temporary weight or relief cuts may be required to ensure adequate contact.
- Coverage Rate
Substrate Coverage Concrete, gypsum, tectumn 1 gallon per 100 sq. ft. Fiberglass 1.5 gallons per 100 sq. ft. Smooth BUR 2 gallons per 100 sq. ft. Coverage Rate Bead Size 1 gallon per 100 sq. ft. 4 beads, 4"x4" per 4"x4" board 2 gallons per 100 sq. ft. 4 beads, 1"x4" per 4"x4" board - Application Precautions
- Do not apply if temperatures are expected to drop below 50°F within 6 hours of application.
- Not intended for areas that pond water.
- Not recommended for insulation boards larger than 4"X4".
- Do not use warped or curled boards.
- All insulation boards must lay flat upon the substrate.
- Do not apply to damp or wet surfaces.
- Do not freeze.
- Do not thin.
- Clean Up
- Immediately rinse/flush equipment and tools with water after use.
- If the material has dried use mineral spirits, exercising all flammable liquid precautions.
- Use waterless hand cleaner on the skin.
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Weight Per Gallon | 8.8 - 9.1 | lbs. | D2939 |
| Solids by Weight | 68 - 72 | % | D2939 |
| Solids by Volume | 66 - 70 | % | D2697 |
| Viscosity (2.5rpm) | 25000 - 35000 | cps | Brookfield, T-spindle |
| pH | 9 - 10 | - | - |
| Drying Time (Touch, 70°F/50% R.H.) | 30.0 | minutes | - |
| VOC | max. 2 | gm/liter | EPA Method 24A |
Packaging & Availability
- Packaging
- 5-gallon pails.
- 55-gallon drums.
Storage & Handling
- Shelf Life (70°F/50% R.H.)
- 1 year