Products in Agricultural Films: Dimensional Stability

Talc HFM 25 is sub-microns particle size platy talc with a high surface area & high aspect ratio to provide excellent barrier properties. During injection molding, these talcs act as ideal reinforcing fillers which provide greater stiffness & impact strength better dimensional stability. It is compatible with all thermoplastics & thermosets.

PBT unreinforced, highly impact modified

PPS, linear, unreinforced, impact modified

POM-CF10, POM copolymer, medium viscosity, carbon fiber reinforced, electrically conductive

PPS, cross-linked, GF 40, with improved hydrolysis resistance for applications in the automotive engine compartment.

BARLOG plastics GmbH Kebablend® / WR 01/1120/2110 is a special compound based on POM, which combines high strength and rigidity with good sliding behavior and high wear resistance.

BARLOG plastics GmbH Kebablend® / M FE 161101 PA12 is a development product based on PA12 for the production of injection molded magnets. Due to the high degree of filling with rare earths (SmCo), Kebablend® / M FE 161101 enables the injection molding of very powerful magnets.

GEHR PBT® is a semi-crystalline material from the polyester family of plastics and, due to its good thermal and mechanical properties, is counted among the polymer group of engineering plastics. It has a high surface hardness and good sliding and wear behavior.

MB 1150 is an Avocado colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1150 is low density foam of approximately 15lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1150 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

MB 1100 is an Olive colored rigid closed-cell polyurethane foam tooling and modeling board. MB 1100 is low density foam of approximately 10lbs/ft³ board. Easily cut using CNC machining equipment or by hand the MB 1100 is perfectly suited for temporary master models, architectural design models, foundry patterns as well as design verification and prototype tools.

POM copolymer unreinforced, low viscosity, laser-inscribable

PBT unreinforced, medium viscosity, injection molding type with optimized toughness

Continental Carbon N550 is a carcass grade black with low surface area, and does not impart good abrasion resistance. Good dimensional stability for extruded profiles, hoses, belts, brake diaphragms, and plastic piping.

BARLOG plastics GmbH Kebablend® / WR 01/2420 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material has medium strength and a high elongation at break.

BARLOG plastics GmbH Kebablend® / WR FE 161104 is a special compound based on ABS, with improved sliding and wear behavior as well as low noise when friction is paired with plastic elements.

linear PPS, 30% glass fiber reinforced, impact resistant, hydrolysis stabilized

PBT unreinforced, injection molding type, also suitable for extrusion, highly viscous

POM-HI, POM copolymer unreinforced, medium viscosity, impact modified

PBT + PCT, unreinforced, increased heat resistance, impact modified

KEBABLEND / WR 01/2105 is a special compound based on POM, which has very good sliding behavior and high wear resistance.

BARLOG plastics GmbH Kebaform® / C 901 TS is a specially modified type, which is characterized by excellent sliding and wear properties. Despite the highly efficient modification with PTFE and a special silicone oil, Kebaform® / C 901TS has excellent mechanical properties. Kebaform® / C 901TS is used wherever high demands are placed on wear resistance, uniformity of friction behavior under changing conditions and low noise levels, and at the same time the mechanical property profile of a technical construction material is required. Kebaform® / 901TS is particularly suitable for sliding pairings with changing operating conditions, e.g. B. When starting behavior without stick-slip effect is just as required as high wear resistance over the entire service life.

PBT unreinforced, injection molding type, low viscosity

VTEC™ GF63 is a High temperature resistance and it is Superior mechanical properties

VTEC™ BG21 is a High temperature resistance and it is Superior mechanical properties

linear PPS, 20% glass fiber reinforced, laser weldable, natural

KEBABLEND / WR 01/2120 is a special compound based on POM, which has very good sliding behavior and high wear resistance.

Nylene Glass and ceramic fiber reinforced nylon 6 injection molding material Designed to provide high dimensional stability, very high stiffness, and a hard surface, while maintaining the heat and chemical resistance typical of nylon products Suitable for such uses as valve bodies, pump housings, hydraulic fittings and couplings, and other applications which require this unique set of characteristics

GEHR PEI® has a high mechanical strength in connection with a good chemical and heat resistance (operating temperature up to +170 °C), good dimensional stability and creep resistance. lts unique torque strength permits the economical substitution of machined fabricated small parts from steel.

GEHR POM® 10 PE (GLIDE) are used for tribological applications in which increased sliding wear is to be expected, POM-10PE is frequently used, whose sliding properties have been significantly enhanced. This type of POM-C with modified sliding properties also has a raw material food contact approval.

POM copolymer unreinforced, medium viscosity

Semi-crystalline high-performance plastic with very good sliding properties and very good mechanical Properties even under thermal stress. In addition, PEEK is characterized by a excellent chemical resistance.

BARLOG plastics GmbH Kebablend® / WR XB 111001/12 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

POM copolymer unreinforced, medium viscosity, tribologically modified, optimized sliding and wear behavior

GEHR PSU® is amber-colored, transparent material belongs to the group of amorphous high-performance plastics. Polysulfone has a good heat deflection temperature and heat aging resistance (-100 °C to +160 °C). In addition, this material has a high hardness and strength, very good hydrolytic stability and high radiation resistance (permeable to microwaves up to 2.45 GHz). PSU also has high dimensional stability and resistance to β- and γ-, X-rays and infrared rays. However, PSU is not UV stable and notch sensitive.

BARLOG plastics GmbH Kebablend® / WR XB 111001/1 is a special compound based on POM, which has very good sliding behavior and high wear resistance. The material is also characterized by noise-dampening properties.

GEHR PVDF® shows a higher tensile strength, pressure resistance and dimensional stability than the related PTFE, but friction and insulation properties are lower. PVDF has a high mechanical strength and toughness at lower temperature and it’s self-extinguishing. The operating temperature ranges from -30 °C to +150 °C. PVDF shows a high resistance to chlorine, bromine and high-energy radiation.