Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
Applications & Uses
- Applications
- Application Details
- For Mixing the Product: Twin paddle mixer, steel container.
- Method of application: Brush, roller.
- PMMA Catalyst Dosages
Substrate
TemperaturePMMA Catalyst Pot Life Hardening Time %pbw. approx. minutes approx. minutes 0°C 3 32 - 36 50 - 60 +10°C 2 18 - 22 45 - 55 +20°C 1.5 12 - 14 35 - 45 - Surface Preparation
- Ensure all areas are clean, dry and free from dust, dirt, corrosion and general surface contamination.
- All oils, grease, etc. should be removed with suitable degreasing solution pre application onto any pre-applied PMMA.
- Concrete and steel surfaces should be preferably Bristle Blasted/Grit blasted to SA 2½ in accordance with DIN 55929.
- Non-ferrous metals must be cleaned and prepared by Bristle Blasting or Grit blasting.
- Advice on Application
- Due to exothermic reaction with mixing process, please ensure the product is mixed in a steel container.
- First stir the PMMA-Based Waterproofing liquid Coating with a paddle mixer thoroughly.
- Then add the PMMA Catalyst while stirring the waterproofing liquid coating at a slow speed.
- Mix for 1 - 2 minutes.
- You must not dose less than the given quantity of PMMA Catalyst, as this will jeopardize the curing process.
- You must also avoid overdosing the PMMA Catalyst, as this can likewise lead to serious curing problems.
- The material must be applied as soon as the PMMA Catalyst has finished dissolving in the resin components.
- The mixing time is about 1-2 minutes.
- Equipment Cleaning
- If work is interrupted or when it is completed, clean the tools thoroughly with cleaning agent within the pot life of the material.
- This can be done with a brush.
- Do not use the tools again until the cleaning agent has evaporated fully.
- Simply immersing the tools in the cleaning agent will not prevent the material from hardening.
- Practical Coverage
Practical coverage can vary considerably depending on method of application, surface roughness, weather conditions and complexity of the structure.
- Theoretical Coverage
3.3 kg/m².
- Application Temperature
0 - 30 °C
Properties
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Solids by Volume | 100.0 | % | - |
| Typical Thickness (DFT) | min. 40 | microns | - |
| PMMA Catalyst by Weight | 1.5 - 3 | % | - |
| Viscosity | 180 - 250 | mPa·s | - |
| Density (D₄²⁰) | 0.99 | g/cm³ | EN ISO 2811-2 |
| Flash Point | 10.0 | Flash Point | DIN 51 755 |
Safety & Health
- Safety Advice
- Avoid skin and eye contact i.e. wear gloves, goggles, etc.
- Ensure good ventilation, mechanical if necessary.
- Store and use away from heat and flame.
- Do not eat or smoke in the vicinity of work.
- Wash hands before eating.
Packaging & Availability
- Packaging
10kg container.
Storage & Handling
- Pot Life
- At +20°C 100g, 1.5% pbw. PMMA Catalyst
- Approx. 12 - 14 minutes.
- Applies only to two component products and refers to the time the mixture remains usable.
- Storage & Handling
Storage:
- Store in a safe place out of the reach of children.
Shelf Life:
- 6 months if stored in the unopened original container in a dry min. 5°C frost-free location.