Products

Crafco RoadSaver 534 sealant is a hot-applied asphalt-based product used to seal and fill cracks and joints in asphalt or Portland cement concrete pavements in hot to cold climates. RoadSaver 534 is supplied in solid form which when melted and properly applied forms a resilient, adhesive, and flexible compound that resists cracking in the winter and resists flow and pick-up at summer temperatures. RoadSaver 534 is used in highway, street, airfield, and parking lot pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. RoadSaver 534 is a free flowing, self-leveling product at application temperature and is specially formulated to cure and lose surface tack quickly following installation. RoadSaver 534 does not contain any reclaimed rubber or ground rubber scrap and is produced using 100% virgin polymer.

Roadsaver Low-Tack is a single component, hot-applied petroleum-based product which is used to fill cracks in both asphalt and Portland cement concrete pavements in moderate to hot climates. RoadSaver Low Tack is supplied in solid form which when melted and properly applied forms a high stiffness, adhesive and flexible compound that resists cracking at winter temperatures and is highly resistant to flow or pick-up at extreme summer temperatures. RoadSaver Low Tack can be used in highway, street, airfield and parking lot pavements. It can be applied to pavement cracks using either pressure feed Melter applicators or pour pots. At application temperature it is a free flowing, self-leveling product. RoadSaver Low Tack is specifically formulated to be a stiff, flow resistant, yet flexible product which is suited for use in areas subject to slow moving vehicle traffic where high resistance to pick-up or tracking is required.

Crafco Pavement Joint Adhesive is a hot-applied modified asphalt composition used to adhere and tack longitudinal cold construction joints in asphalt concrete pavements. Pavement Joint Adhesive increases durability and life of joints through improved bonding and sealing. Long-term research in several studies has proven that Crafco Pavement Joint Adhesive provides the best joint performance of all methods available.

Crafco RoadSaver 963 Gray Sealant is a gray colored, hot applied, single component, elastically modified composition of non-asphaltic ingredients and modifiers used to fill cracks and joints in asphalt and Portland cement concrete pavements. RoadSaver 963 Gray Sealant is supplied in powder/granular form in meltable bags which when melted and properly applied forms an adhesive and flexible compound that resists cracking in the winter and is resistant to flow at summer temperatures. RoadSaver 963 Gray Sealant is used in highway, street, and airfield pavements where the gray color is desired.

Crafco RoadSaver 514 sealant is a hot-applied, asphalt based product used to seal cracks or joints in asphalt or Portland cement concrete pavements in cold climates. RoadSaver 514 is supplied in solid form which when melted and properly applied forms a resilient, adhesive and flexible compound that has a high degree of elongation at low temperatures while resisting flow during the summer. RoadSaver 514 can be used in highway, street and airfield pavements and is applied to pavement cracks or joints using either pressure feed melter applicators or pour pots. At application temperature, it is a free flowing, self-leveling product. RoadSaver 514 is produced for requirements of the Kansas Department of Transportation for crack sealant. RoadSaver 514 has been a quality Crafco product for over 20 years. Due to the softness of the product, RoadSaver 514 is not recommended for use as crack sealant in parking lots or other areas with high levels of foot traffic.

Crafco RoadSaver 960 Gray Sealant is a gray colored, hot applied, single component, elastically modified composition of non-asphaltic ingredients and modifiers used to fill cracks and joints in asphalt and Portland cement concrete pavements. RoadSaver 960 Gray Sealant is supplied in powder/granular form in meltable bags which when melted and properly applied forms an adhesive and flexible compound that resists cracking in the winter and is resistant to flow at summer temperatures. RoadSaver 960 Gray Sealant is used in highway, street, and airfield pavements where the gray color is desired.

Crafco Hot-Applied Bituminous Marker Adhesive is a hot-applied adhesive which, when properly applied, bonds markers and reflectors to both asphalt and concrete pavement surfaces. The adhesive is supplied as an easy to use single component material which is easily melted and poured or pumped onto pavement surfaces. Since it is a hot melt composition, the adhesive sets up on cooling and is ready for traffic in less than 5 minutes. Heating can be performed in either directly or indirectly heated melting units. The adhesive contains no rubber polymers which can degrade at application temperature. Hot-Applied Bituminous Marker Adhesive has been a quality Crafco product for over 20 years.

Crafco RoadSaver 515 sealant is a hot-applied asphalt-based product used to seal and fill cracks and joints in asphalt and Portland cement concrete pavements in moderate to cold climates. RoadSaver 515 is supplied in solid form which when melted and properly applied forms a highly adhesive and flexible compound that resists cracking in the winter and resists flow in the summer. RoadSaver 515 is used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. At application temperature, RoadSaver 515 is a free flowing, self-leveling product. The unique formulation of RoadSaver 515 reduces stress buildup during extension at low temperatures which improves long term performance. RoadSaver 515 has been a top performing quality Crafco product for over 25 years.

RoadSaver 515 MN sealant is a hot-applied petroleum based product used to seal and fill cracks and joints in asphalt or Portland cement concrete pavements in moderate to cold climates. RoadSaver 515 MN is supplied in solid form which when melted and properly applied forms an adhesive and flexible compound that resists cracking in the winter and resists flow at summer temperatures. RoadSaver 515 MN is used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed melter applicators or pour pots. At application temperature RoadSaver 515 MN is a free flowing, self-leveling product. RoadSaver 515MN is produced specifically to meet requirements on the Minnesota DOT for pavement crack and joint sealant. Roadsaver 515 has been a top performing quality Crafco product for over 20 years.

Crafco RoadSaver 522 sealant is a hot-applied asphalt-based product used to seal and fill cracks and joints in both asphalt and Portland cement concrete pavements in cold to very cold climates. RoadSaver 522 is supplied in solid form which when melted and properly applied forms an adhesive flexible compound with high elongation and low stress development at low temperatures, while resisting flow during the summer. RoadSaver 522 can be used in highway, street, and airfield pavements and is applied using either pressure feed Melter applicators or pour pots. At application temperature, RoadSaver 522 is a free flowing, self-leveling product. RoadSaver 522 was developed specifically to perform in temperature extremes and movement conditions that exist in the coldest climates. Over the last 20 years, RoadSaver 522 has proven to be one of the best, if not the best performing crack sealant for very cold climates. Several states and Canadian provinces have adopted specification based on the exceptional performance of RoadSaver 522. Due to the softness of the product RoadSaver 522 is not recommended for use as crack sealant or filler in parking lots or other areas with high foot traffic.

Crafco RoadSaver 515T is a hot-applied asphalt-based product used to seal and fill cracks and joints in asphalt or Portland cement concrete pavements in moderate to cold climates. RoadSaver 515T is supplied in solid form which when melted and properly applied forms a highly adhesive and flexible compound that resists cracking in the winter and is resistant to flow in the summer. RoadSaver 515T can be used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. At application temperature, RoadSaver 515T is a free flowing, self-leveling product. RoadSaver 515T does not contain any ground cured rubber scrap.

Crafco RoadSaver 221 sealant is a hot-applied asphalt-based product used to seal and fill cracks and joints in asphalt or Portland cement concrete pavements in hot to cold climates. RoadSaver 221 is supplied in solid form which when melted and properly applied forms a resilient, adhesive, and flexible compound that resists cracking in the winter and is resistant to flow and pick-up at summer temperatures. RoadSaver 221 is used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. At application temperature RoadSaver 221 is a free flowing, self-leveling product. RoadSaver 221 is a widely used, excellent performing sealant that has been a quality Crafco product for over 30 years.

Crafco Hot-Applied Flexible Pavement Marker Adhesive is a hot-applied thermoplastic bituminous adhesive which, when properly used and applied, bonds markers and reflectors to both asphalt and concrete pavement surfaces. Hot-Applied Flexible Pavement Marker Adhesive is supplied as an easy to use single component material which is easily melted and poured or pumped onto pavement surfaces. Since it is a hot melt composition, Hot-Applied Flexible Marker Adhesive sets up on cooling and is ready for traffic in less than five minutes. Hot-Applied Flexible Marker Adhesive is formulated with premium asphalt, polymers and additives to produce a unique material which holds markers in place and remains flexible at temperatures down to 20°F (-7°C). Hot-Applied Flexible Pavement Marker Adhesive has been a top performing quality Crafco product for over 20 years. Several states have adopted adhesive specifications based on the improved performance of Crafco Hot-Applied Flexible Pavement Marker Adhesive.

Crafco RoadSaver 222 sealant is a hot-applied asphalt-based product used to seal and fill cracks and joints in asphalt or Portland cement concrete pavements in hot to cold climates. RoadSaver 222 is supplied in solid form which when melted and properly applied forms a resilient, adhesive, and flexible compound that resists cracking in the winter and resists flow at summer temperatures. RoadSaver 222 is used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. At application temperature, RoadSaver 222 is free flowing and self-leveling. RoadSaver 222 is produced to meet ASTM D6690 Type III and Federal Specification SS-S-1401C and has been a quality Crafco product for over 30 years.

Crafco RoadSaver 231 sealant is a hot-applied, asphalt-based product used to seal cracks and joints in asphalt or Portland cement concrete pavements in cold to very cold climates. RoadSaver 231 is supplied in solid form which when melted and properly applied forms a resilient, adhesive, and flexible compound with high elongation capability at low temperatures, and resistance to flow during the summer. RoadSaver 231 is used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. At application temperature it is free flowing and self-leveling. Due to its softness, RoadSaver 231 is not recommended for use as a crack sealant in parking lots or other areas with high levels of foot traffic. RoadSaver 231 has proven to be an exceptional performing sealant in very cold climates and has been a quality Crafco product for over 30 years.

Crafco RoadSaver 545 sealant is a hot-applied asphalt-based product used to seal and fill cracks and joints in asphalt and Portland cement concrete pavements in moderate to hot climates. RoadSaver 545 is supplied in solid form which when melted and properly applied forms a resilient adhesive and flexible compound that resists cracking in the winter and resists flow at summer temperatures. RoadSaver 545 is used in highway, street, and airfield pavements and is applied to pavement cracks and joints using either pressure feed Melter applicators or pour pots. At application temperature, RoadSaver 545 is a free flowing, self-leveling product. RoadSaver 545 is produced to meet Arkansas specifications. RoadSaver 545 contains no reclaimed or ground vulcanized rubber material.