Knowde Enhanced TDS
Identification & Functionality
- Chemical Family
- Product Type
- Technologies
- Product Families
Features & Benefits
- Ready-to-Use Product Features
- Advantages
- Easy application
- Ultra-Low V.O.C. formula
- High bond strength
- Strong wet / green grab
- Minimal shrinkage and non-slump for superior contact
- High elastomeric properties
Applications & Uses
- Markets
- Applications
- Application Area
- Cure Method
- Typical Uses
FPI™ UA-5 can be used over both concrete and wood substrates to install finish wood surfaces including solid hardwood planks, laminate hardwood flooring, engineered hardwood flooring, and parquet flooring.
- Coverage
Flooring Product Trowel size Coverage Engineered and Cork up to 7”
wide and up to 5/8” thick.
Solid and Bamboo up to 3”
wide and up to ½” thick3/16” x ¼” x ½”
V-Notch50 - 55
sq. ft. /gal.Wood Flooring over 3” wide
and up to ¾” thick¼” x ¼” x ¼”
Square Notch30 - 40
sq. ft. /gal.Finger Block Parquet,
Recycled Rubber Flooring
and Cork Underlayment¼” x ¼” x ¼”
Square Notch30 - 40
sq. ft. /gal.- Surface Preparation
Surfaces must be clean and free from dirt, dust, debris, oils, waxes, or any other material that would inhibit bonding of the adhesive to the substrate, if some materials are difficult to remove, surface abrasion may be required. For use only in interior environments. Temperatures should be maintained as close to 70ºF and 45% relative humidity at least 72 hours before, during, and after installation of product. Floor moisture must be measured prior to installation. Maximum moisture presence is 6lb. Per 1000/sq.ft. per 24 hours, based on a Calcium-Chloride (CaCl) test, a maximum of a 4.5 reading on a TRAMEX Concrete Moisture Encounter, or 80% RH. Floor level can not exceed variance of 3/16” per 10 feet. Follow all surface preparation instructions issued by the manufacturer of wood finish surfaces.
Flooring Installation
Condition finish flooring surface and install in accordance with wood manufacturers directions. Pour product over the correctly prepared surface, and trowel in place using a suitable notch trowel for the application of this product (see trowel chart).Press flooring firmly into FPI UA-5 adhesive immediately after troweling. Starter rows should be taped to help prevent movement. Periodically check to make sure there is 100% adhesive coverage and transfer to the flooring. Do not spread more adhesive than can be covered in 45 minutes.
Additional Instructions
Use a weighted roller in accordance with wood manufacturer's instructions. Allow a minimum of 4 hours to cure before light foot traffic can begin. Normal traffic can resume after 12 hours.
Once UA-5 Cures It is Extremely Difficult to Remove and Will Etch Finish Surfaces.
Clean Up : Fresh adhesive – use FPI™ UAR (Urethane Adhesive Remover) sparingly with a clean, white cotton cloth to immediately clean any adhesive from the surface of prefinished floors. Always test on a scrap of the flooring material prior to using on an installed floor to ensure that the cleaner will not damage the surface.
Properties
- Color
- Typical Properties
| Value | Units | Test Method / Conditions | |
| Open Time (70º F, 45% RH) | 1.3 | Hours | |
| Tack Onset (70º F, 45% RH) | 60 | minutes | |
| V.O.C. Level | max. 30.0 | g/l | - |
| Flash Point | min. 250 | °F | - |
| Freeze / Thaw | Stable | - | - |
Safety & Health
- Cautions and Limitations
FPI™ UA-5 is not a moisture barrier by itself. If moisture levels in the substrate exceeds recommended levels, contact Technical Support for further instructions. Do not use on wet, frozen, friable, or contaminated surfaces. Do not add water or stir the adhesive. UA-5 was formulated for professional use.
- Health and Safety
Wear protective clothing and eye protection when using this product. Wear rubber gloves during application of product to avoid contact with skin. Use only in well ventilated areas.
Emergency Procedures
- Skin - Wash thoroughly with soap and water.
- Eyes - Flush with water for 15 minutes. Seek immediate medical attention.
- Inhalation - Remove person to fresh air.
- Ingestion - Do not induce vomiting, seek immediate medical attention.
KEEP OUT OF REACH OF CHILDREN AND PETS.
Packaging & Availability
- Packaging Type
- Packaging
Available in 5 gallon and 4 gallon metal pails
Storage & Handling
- Shelf Life
Shelf Life is 12 months for unopened containers stored in ambient conditions.