LNP™ LUBRILOY™ Compound UX99725

Identification & Functionality

Additives Included

Lubricant (Unspecified),

Proprietary

Chemical Family

Polyamides

Polymer Name

Polyphthalamide (PPA)

Plastics & Elastomers Functions

Resin

Technologies

Plastics

Product Families

Plastics — Engineering & Specialty Polymers

Polyamides

Features & Benefits

Labeling Claims

No Added PFAS

Materials Features

High Temperature Resistance,

Lubricated,

No Added PFAS,

Unreinforced,

Very Good Heat Resistance,

Wear Resistant

Applications & Uses

Markets

Automotive & Transportation,

Electrical & Electronics

Applications

Automotive & Transportation — Automotive

Exterior & Body,

Powertrain & UTH

Electrical & Electronics — Parts & Components

Housings & Enclosures

Plastics & Elastomers End Uses

Automotive Applications,

Automotive Exterior Parts,

Automotive Under The Hood,

Enclosure

Plastics & Elastomers Processing Methods

Injection Molding

Properties

Mechanical Properties

	Value	Units	Test Method / Conditions
Tensile Stress (Yield, Type I, 5 mm/min) ¹¹	68	MPa	ASTM D638
Tensile Stress (Break, Type I, 5 mm/min) ¹¹	60	MPa	ASTM D638
Tensile Strain (Break, Type I, 5 mm/min) ¹¹	20	%	ASTM D638
Tensile Strain (Yield, Type I, 5 mm/min) ¹¹	8	%	ASTM D638
Tensile Modulus (at 5 mm/min) ¹¹	2244	MPa	ASTM D638
Flexural Modulus (at 1.3 mm/min, 50 mm span) ¹¹	2010	MPa	ASTM D790
Flexural Stress (at 5% strain, 1.3 mm/min, 50 mm span) ¹¹	82	MPa	ASTM D790
Tensile Stress (Yield, 5 mm/min) ¹¹	66	MPa	ISO 527
Tensile Stress (Break, 5 mm/min) ¹¹	64	MPa	ISO 527
Tensile Strain (Yield, 5 mm/min) ¹¹	7	%	ISO 527
Tensile Strain (Break, 5 mm/min) ¹¹	9	%	ISO 527
Tensile Modulus (at 1 mm/min) ¹¹	2153	MPa	ISO 527
Flexural Modulus (at 2 mm/min) ¹¹	2180	MPa	ISO 178
Flexural Strength (at 2 mm/min) ¹¹	94	MPa	ISO 178

Physical Properties

	Value	Units	Test Method / Conditions
Specific Gravity ¹¹	1.119	—	ASTM D792
Density ¹¹	1.11	g/cm³	ISO 1183
Water Absorption (at 23°C, 24hrs) ¹¹	0.5	%	ISO 62-1
Melt Volume Rate (at 330°C, 2.16kg) ¹¹	6	cm³/10 min	ISO 1133
Mold Shrinkage (flow) ᵍ ¹¹	1.2 - 1.7	%	SABIC method
Mold Shrinkage (xflow) ᵍ ¹¹	1.5 - 2	%	SABIC method
Wear Factor Washer ¹¹	35	10^-10 in^5-min/ft-lb-hr	ASTM D3702 Modified: Manual
Dynamic COF ¹¹	0.15	—	ASTM D3702 Modified: Manual
Static COF ¹¹	0.14	—	ASTM D3702 Modified: Manual

Thermal Properties

	Value	Units	Test Method / Conditions
Heat Deflection Temperature (at 0.45 MPa, 3.2 mm, Unannealed) ¹¹	140	°C	ASTM D648
Heat Deflection Temperature (at 1.82 MPa, 3.2mm, Unannealed) ¹¹	121	°C	ASTM D648
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000097	1/°C	ASTM E831
Coefficient of Thermal Expansion (at -40°C to 40°C, flow) ¹¹	0.000097	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.000092	1/°C	ISO 11359-2
Coefficient of Thermal Expansion (at -40°C to 40°C, xflow) ¹¹	0.000092	1/°C	ASTM E831
Vicat Softening Temperature (Rate B/50) ¹¹	151	°C	ISO 306
Vicat Softening Temperature (Rate B/120) ¹¹	151	°C	ISO 306
Heat Deflection Temperature/Bf (at 0.45 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	139	°C	ISO 75/Bf
Heat Deflection Temperature/Af (at 1.8 Mpa, Flatw 80*10*4, sp=64mm) ¹¹	119	°C	ISO 75/Af

Impact Properties

	Value	Units	Test Method / Conditions
Izod Impact (Notched, at 23°C) ¹¹	118	J/m	ASTM D256
Izod Impact (Notched, 80*10*4, at 23°C) ¹¹	13	kJ/m²	ISO 180/1A
Charpy Impact (at 23°C, V-notch Edgew 80*10*4 sp=62mm) ¹¹	15	kJ/m²	ISO 179/1eA

Injection Molding

	Value	Units	Test Method / Conditions
Drying Temperature ⁷	120	°C	—
Drying Time ⁷	4	Hrs	—
Melt Temperature ⁷	315 - 330	°C	—
Front - Zone 3 Temperature ⁷	325 - 340	°C	—
Middle - Zone 2 Temperature ⁷	315 - 325	°C	—
Rear - Zone 1 Temperature ⁷	310 - 320	°C	—
Mold Temperature ⁷	150 - 170	°C	—
Back Pressure ⁷	0.2 - 0.3	MPa	—
Screw Speed ⁷	30 - 60	rpm	—

Note

• ᵍ Measurements made from Laboratory test Coupon. Actual shrinkage may vary outside of range due to differences in processing conditions, equipment, part geometry and tool design. It is recommended that mold shrinkage studies be performed with surrogate or legacy tooling prior to cutting tools for new molded article.
• ⁷ Injection Molding parameters are only mentioned as general guidelines. These may not apply or may need adjustment in specific situations such as low shot sizes, large part molding, thin wall molding and gas-assist molding.
• ¹¹ The information stated on Technical Datasheets should be used as indicative only for material selection purposes and not be utilized as specification or used for part or tool design.

 

Packaging & Availability

Regional Availability

• Americas
• Asia
• Europe
• North America