Products in Power, Water & Utilities: Good Abrasion Resistance

Pure ULTRA high molecular weight high density polyethylene homopolymer polymer in finely sized rounded powder form. Avg. = ~70- micron. Molecular weight in excess of 2,000,000.

Pure very high molecular weight high density polyethylene homopolymer polymer in finely sized rounded powder form. Avg. = ~75 micron. Molecular weight of approximately 500,000.

SP Series™ SHP1200-1 is a ultra high molecular weight polyethylene (UHMWPE) polymer in powder form. These unique materials exhibit very high toughness. SP Series™ materials are pure polyethylene with broad regulatory compliance and contain no residual chemicals or additives that may interfere with some application requirements. SP Series™ powders are well suited for use in water, chemical and gas filter applications. SHP1200-1 can be independently sintered into a filter or used as a binder for activated carbon filter.

Pure ULTRA high molecular weight high density polyethylene homopolymer polymer in finely sized rounded powder form. Avg. = ~130- micron. Molecular weight in excess of 2,000,000.

Electro Chemical Engineering EC Duro-Bond Chlorobutyl is an uncured chlorobutyl elastomer applied in sheet form and vulcanized after application using exhaust steam. Sheet thicknesses of 120 mils (2.3 mm), 150 mils (3.4 mm), and 180 mils (4.6 mm) are available.

RESOLCOAT 7050 is a Abrasion resistant epoxy gelcoat. which has excellent abrasion resistance and has good fire resistance. This new generation system has a viscosity and a thixotropy suitable for brush application on heated tools

Duro-Bond Hypalon is an elastomeric sheet lining having excellent abrasion, heat, and corrosion resistance.. It is available either as a precured lining or as an uncured lining that must be vulcanized with steam or hot air cured before it can be used.

RESOLCOAT 7060 is an epoxy clear or pigmented Gelcoat. Which has improved UV resistance, room temperature cure & high gloss and choice of slow and fast hardeners. RESOLCOAT 7060 epoxy gelcoat is specially formulated for the production of structural composites parts or tools requiring high mechanical & abrasion properties and room temperature curing. Two versions are available depending on the pot life needed : 1h45min for large parts or 16min for high production outputs, with a very fast curing time in film for the fast version - closer to a polyester curing time than to a typical epoxy. In both cases, the gelcoat may be ordered in its clear version (mainly for parts) or colored version for tools or parts production.

Duro-Bond PVDF is a laminated sheet lining consisting of a layer of polyvinylidene fluoride (PVDF) resin laminated onto a layer of fabric cloth or vulcanized chloroprene rubber backing that is readily bonded to steel, concrete, or FRP substrates.

Beijing Evergrow Resources PVDF SHEET sheet has the good corrosion resistance ; good mechanical properties; good thermal and electrical properties and good aging resistance ,it's widely used in petrochemical , metallurgy,food,paper ,textiles,semi-conductor,mechical engineering,medcine,nuclear insdustries. and PVDF sheet back with glass fiber can as the good lining materials used in Cheimal popes and tanks.

Duro-Bond S-123 are offered by electro chemical. Sheet thicknesses of 120 mils (2.3 mm), 150 mils (3.4 mm), and 180 mils (4.6 mm) are available.

Polyslick® UHMW Sheet exhibits the properties of excellent impact strength, abrasion resistance, low coefficient of friction, as well as very good chemical resistance. This industrial grade material is also moisture, stain and odor resistant, and is FDA approved to be used in the food processing industry. The material is ideally suited for wear applications especially in contact with metals. UHMW is widely used in industrial applications such as chute linings, dock bumpers, paper machine parts, and conveyor wear strips and can easily be machined with ordinary wood working tools.

Duro-Bond Neoprene is an elastomeric sheet lining having good abrasion and chemical resistance. It is available either as a precured lining or as an uncured lining that must be vulcanized with steam or hot air before it can be used. Sheet thicknesses of 60 mils (1.1 mm), 120 mils (2.3 mm), 150 mils (3.4 mm), and 180 mils (4.6 mm) are available.